V1.06b21(E) Fix this issue: 1.When DI-804HV connects to a PPPoE server(also a DHCP server) under dualAccess PPPoE WAN type, the magic number of the keepalive packets will occur some errors 2.DI-804HV can't work normally with DHCP Relay device 3.After DI-804HV's PPTP/L2TP server received this rejected packet for "Address/control field compression" from client, it still does this request V1.06b20(E) Remove unneeded log information. V1.06b19(E) 1. On page Tools->Time, device is only allowed to choose year 2007(add to 2010). 2. New remote management. V1.06b17,18(E) Under the Backup connection, added the re-send the IPCP-request mechanism. V1.06b16(E) 1. Device configured as Dynamic DualAccessPPTP/PPPoE with manual/connect on demand function. When pressing disconnect device close tunnel and Keep address from WAN-PHY. 2. Add the Clone Mac function to the DualAccess PPTP WAN type. 3. Device makes only one try to connect to PPTP server. 4. Device request NTP server every 10 seconds. 5. IGMP Proxy doesn't work with DualAccess PPTP/PPPoE. IGMP request problems doesn't forwards to WAN-PHY and WAN-PPP. 6. Device configured as WAN-StaticIP. Device doesn't forward TCP.RST response from Server if service unavailable. 7. State table doesn't work normally. 8. Add new PeanuHull version. 9. Add URL Blocking characters number from 30 to 50. 10. Add Domain Blocking characters number from 30 to 45. V1.06b15(E) Add 15 DHCP static IP clients(the total clients are 30). V1.06b14(E) Fix the issue: When the ISDN backup line is up, if no any traffic from lan side, the ISDN line shall be dropped by idle time out. V1.06b13(E) Fix the issue: 1.ThešDI-824VUP+ is configured with Dialup Network and PPPoE with Auto-backup. When DI-824VUP+ goes online over backuped, the UI of connection cant normally show the Dial-up states. 2.Use VLC-Server for tests. DI-804HV can pass IGMP flow inside LAN. But then we close VLC-client. Flow still exist in LAN ports. V1.06b12(E) 1.Increase the length of FQDN feature for VPN function to 25 bits. 2.Add IGMP function. V1.06b10(E) Fix those issues below: 1.DHCP clients cant get IP address of secondary DNS of the device. 2.Process the IPSEC will initial the session of PPTP if both device located in the same network. 3.PPTP/L2TP connection cant be establish normally. 4.If users enable both anto-reconnect and DDNS function in VPN function, the device cant trigger to establish the VPN connection. V1.06b09(E) Fix Russia issues below: 1.When adding new rule to QoS and appling and restarting router, the last added rule becomes enabled and others become disabled, and also the router forgets their protocols (TCP:80šbecomes *:80). 2.Because DI-804HVs minimal lifetime is 300 seconds. Therefore, UI will block the setting when users enter the value which is lower than 300 seconds. V1.06b08(E) Fix Russia issues below: a. Source port issue b. PPTP DNS issue c. PPTP and IPSec issue d. PPPoE Connective issue e. The issue of PPP CHAP CHALLANGE packet on DI-8xx V1.06b07(E) 1. Customer uses GPRS modem to dial-up Internet. But, customer can't enter init string: AT+GDCONT=1,"IP","internet.mts.ru" Device can't accept "." V1.06b06(E) 1.1. Add new PeanutHull DDNS function for new PeanutHull DDNS version. V1.06b05(E) 1.Enable two DI-824VUP+s VPN Xauth function and VPN auto-reconnect function. Then, try to establish VPN tunnel between two DI-824VUP+s. When VPN tunnel is established, click the disconnection button. Then, the VPN tunnel will not be able to be established again. 2.In Wizards WEP settings, there is a 256 bit option. Please delete it. 3.Switching the NTP time, but the time will not be changed. 4.The bridge mode will be removed.. V1.06b04(E) 1. Fix the problem which DFL-210 to DI-824VUP+ Xauth not working. V1.06b03(E) 1. Fix the problem which wireless client cant get IP address normally. V1.06b02(E) 1. DFL-210 to DI-824VUP+ Xauth not working. V1.06b01(E) 1. Wireless mini PCI chipset is changed to Ralink from TI. V1.06(E) 1. Rename from V1.05b09. V1.05b09(E) 1. Windows L2TP client cant connect to DI-824VUP+ server. V1.05b08(E) 1. When connect to GPRS mode, the firmware will be able to show some error messages. V1.05b07(E) 1. Two DI-824VUP+ and Radius through VPN not working V1.05b06(E) 1.Add item to Enable or disable keepalive with arp. 2.The WAN IP address or WAN gateway must check by submask 3.Add Interface field in static routing function V1.05b05(E) 1. WPA-PSK doesn't work with some ASCII characters_Canada. V1.05b04(E) 1. Fixed Static and dynamic VPN can not work at the same time. 2. Add the function Change the TTL value. 3. Add Qos Function. 4. Add IPsec Filter function. 5. Add Xbox support function. 6. Add VPN-auto reconnect function. 7. Add Remote ID & Local ID function. 8. Fixed While using pptp vpn,can not browse the remote UI. 9. Fixed Cant use more than four PPTP VPN clients to connect to the PPTP VPN Server. 10. Fixed Both routers use VPN Traversal to establish VPN tunnel, they cant ping the other side. v1.05b03(E) 1. Modify log page. 2. Add port unumber Remote admin host. 3.Modify the update server of . v1.05b02(E) 1.Support Ericssion GPRS Modom. v1.05b01(E) 1.Routers WAN IP can respond Ping packet that is sent out by UIs Ping tool. 2.Users cant enable/disable URL blocking if there are 10 rules in the list. 3. Fixed When Firewall setups some rules,there are some problems by enabling SPI modes v1.05b01(T,S) 1. Add local identity configuration field. v1.05(T,S) 1.Fixed Show wrong message in the Wizard when the user setups the same passward. 2.Modify the password item of ppp series to add ********. 3.Mpdify the disable item of Domain filter 4.Modify the wrong message in status page while enabling 128 or 256 Wep key. 5.FixFails to establish IPSec tunnel with D-Link DFL-100. 6.Fixed the UI of ddns setting. 7. Fix static dhcp table only can set up to 15 item after 15 item will show error message. 8.FixedMsn can not login normally,when the user opens port 1723 in the virtual. 9.Fix the following problems: (1) If users choose Group2 or Group5 as the DH-Group of IKE proposal, two DI-824VUP cant establish IPSec tunnel successfully by using aggressive mode. 10.Support GPRS modem. 11.Support RTP traffic pass-through. 12.Add anšadditional field of authentication method (including Auto, PAP, CHAP, MS_CHAPv1; Default is Auto)šat the Dial-upšWAN configuration page. 13.Add Status Connection. 14.Support Netmeeting put the client in the Virtual Server. V1.02b01 1.Fix "When the user inputs 32 keys or more in WPA_PSK, the router will not allow of this setting." v 1.04 1.LAN PCs can't access remote FTP server if router is in SPI mode. 2.Router can't drop PPPoE connection even though the idle time has expired. 3.Fixed "daylight saving when the users setup to span two years." 4.Dynamic VPN can't be reconnected again if remote clients reboot. V1.04 1.Fix"Wireless Setting UI(Radio on/off). 2.Add Statement in the help of Wireless Setting. V1.03b03 1. Support Syslog server on WAN side. 2. Fix the device will hang down when WAN & LAN loop-back. 3. Fix speed Enhance Mode function will be disabled when enables WPA-PSK function. 4.Support IPSec NAT-Traversal. 5.There are a lot of incorrect VPN rules in VPN Status window. 6.Fix failed items of CDRouter test. V1.03b02 1.Fix failed items of CDRouter test. 2.Change firewall destination IP from * to real destination IP if the rule is derived from Virtual Server. 3.Support NO-IP DDNS service. 4.Fix the following problem: (1) Netmeeting (on Microsoft Windows 2000) is unable to connected success through VPN tunnel. (2) Can't establish Manual IPSec tunnel with early firmware version. 5.Add Radio on/off in wireless Configuration. 6.Improve wireless Stable. V1.03b01 1.Support xAuth (Client and Server mode) authentication with IPSec connection. 2.Support i2eye ALG. 3.Prevent different devices from using the same XID to send DHCP request. 4.Fix the following problem: (1) Virtual Server doesn't work if public port and private port are not the same. (2) Router(with WAN type: Dial-up connection) will auto-reboot if LAN PC reboots. 5.Enhance the wireless performance.(Call G+) 6.Change the value of Max. number of tunnels from 0 to 1. V1.03 1.Change Firmware Version as V1.03 2.Fixed"Some pages are not displayed correctly in Netscape and Mozilla WEB browsers" 3.Add some VPN settings Help. V1.02b01 1.Change Firmware Version as V1.03 V1.02 1. If users enable PPTP or L2TP server on DI-824VUP(+),then any WAN host can Ping to LAN IP of the router successfully(without establishing PPTP or L2TP connection first. 2. More than one PPTP or L2TP clients behind NAT device can't establish PPTP or L2TP connetion with DI-824VUP(+) at the same time.(only allow one PPTP or L2TP connection.) 3. Fix MAC filter bug. 4. Support 2 or more connections when using MPPE encryption with PPTP and L2TP server. V1.01b04 1.Change Firmware Version as V1.02 V1.01b03 1.Add IPSec VPN Keep-alive mechanism. 2.Add D-Link web cameras(DCS-900, 1000, 2000, 3120, 5300) into default lists of Virtual Server. 3.Add MPPE encryption with PPTP and L2TP server. (Note. MPPE can only works with MS_CHAP authentication.) 4.Support PPTP WAN type can connect to PPTP server of Microsoft Windows 2000. 5.Change firewall mechanisms. (It's recommended to reset configuration to factory default after upgrading to this firmware.) 6.The TI Wireless Module is the same with DI-724P(V1.01) 7.Fixed "the ftp conection is broken in VPN IP-sec Tunnel". V1.01b01 1.Fixed "Linux-Dns server can not query under Nat,when SPI mode is enabled.(Test) 2.Chnage Default Setting "Connect mode select changes as Connect-on-denand Maximunm Idle Time is 5 minutes."(Test) 3.Fixed "the ftp conection is broken in VPN IP-sec mode". 4.Support IGMP for Singapore.(Test) 5.Change Ti wireless Card Module and verify wireless stable.(Test) 6.Verify BigPond problem in australia.(Test) 7.Fix the problem about L2TP WAN connection doesn't work in Israel.(Test) V1.01b01 1.Change Firmware Version as V1.01. V1.01 1.Fix UI error when swith VPN configuration pages. 2.Fix the problem about mail alert function can't transfer mail with some SMTP servers,like Pchome. 3.Replace the real key value with asterisks in VPN configuration pages. 4.Support SMTP authentication with mail alert function. 5.Modify the same address of Sender and Receiver in mail alert function. v1.00b7 1.Change Firmware Version as V1.01. 2.Change the sender of Format.(change admin@wan-ip address to admin@domain-name). But there is still a bug,some mail-servers access to deny for admin@domain-name, like admin@pchome.com.tw,Amit will modify the same address of Sender and Receiver. For example,the receiver is D-Link@dlink.com.tw and the Sender is also D-Link@dlink.com.tw. Amit will modify this by next Fw. v1.00b06 1.Support X-Box about TCP Fin-test of UPNP function. 2.Fix "The device can not renew leased-time automatically when wan type is dynnamic ip address." 3.Modify Firewall rule list(change Lan ip 192.168.0.1 to *). 4.Modify "the wireless connection is down,when DWL-G650+ enables 8x Mode. v1.00b04 1.Fix "When Setuping Mac filter,the setting will skip to Domain Blocking." in Filter Page. 2.Fix "The System-log will not show filter-log when enabling the rules of domain filter." in the Filter page. 3.Fix "The settings,like Authentication type ,SSID broadcast and 8X Mode will skip in the Perfromance page." 4.Fix "The wireless can not work(The wireless button is gone) when the wan type is ppp(pppoe,l2tp,pptp or dial-up) and enables WPA ro 802.1x." 5.Fix "Power save makes the wirelss connection down,for example,Centrino or wireless-clients enable power-save mode. 6.Fix "The vpn function will authenticate incorrectly when setting many ipsec proposals( different group)." v1.00b03 1. Add Connection Mode select. 2. Add Tx Power function. v1.00b02 1.Change UI title image. 2.Fix Wireless SSID will lost "+" when click WEP disable to enable. 3.Improve the wireless throughput. 4.Fix when Wep setting is not working in Wizard mode. 5.Fix that Wireless tab under Status is not working. 6.Fix that Intersil 11g can not associate when G mode only. 7.Fix DWL-650+ can not associate when SSID broadcast disables. v1.00b01 1. Add WPA. 2. Add L2TP. 3. Add PeanutHull. 4. Add Daylight Saving. 5. Change Domail Filter seat. v1.00 1. Fix remote management. 2. Fix wireless card fail. 3. Fix DynDNS.org. 3. Fix Wireless SSID will lost "+" when click WEP disable to enable. v1.00 First release.