/*------------------------ Software Release Note --------------------------- * * This document is the Standard Format for Software Release Note. * *----------------------------------------------------------------------------*/ ******************************************************************************* *[PRODUCT NAME] : D-Link DES-1252 * ******************************************************************************* _______________________________________________________________________________ RELEASE VERSION : 1.11.01 RELEASE DATE : 2008/12/15 RELEASE BY : George Huang _______________________________________________________________________________ [CHECK-CODE] : D559 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : athena:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-11-01 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.11.01 [PLM-NO] : [N/A] _______________________________________________________________________________ New Feature: ------------- N/A Bug Fixed: ------------- 1. Fixed the bug that PING/Web access is fail when deleting VLAN on Asymmetric VLAN mode. Changed: ------------- N/A Note: ------------- N/A Known issues: ------------- N/A _______________________________________________________________________________ RELEASE VERSION : 1.11.00 RELEASE DATE : 2008/12/02 RELEASE BY : George Huang _______________________________________________________________________________ [CHECK-CODE] : 300D [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : athena:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-11-00 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.11.00 [PLM-NO] : [N/A] _______________________________________________________________________________ New Feature: ------------- N/A Bug Fixed: ------------- 1. Fix the bug that management vlan does not work if users apply management VLAN to vlan group which exceeds the 32th vlan group. 2. Fix the bug that wrong checking on trunk member while setting port STP mode on WEB UI. 3. Fix the 802.1x bugs as below: 1. Enable 802.1x and set Re-auth period to 25; enable STP. The control port can not connect to to the device. 2. Cannot block the 1x port after authentication fail. 3. The control port is authrized, unplug the port the status will remain in "Authrized" even after the pass the reauthrize period. 4. Fix the bug that device does not reponding after apply the VLAN configurations in Linux. (Use Firefox 3 web browser) 5. Fixed the issue that switch can not forward AppleTalk Broadcast packet (DA is 09-00-07-ff-ff-ff). Changed: ------------- N/A Note: ------------- N/A Known issues: ------------- N/A _______________________________________________________________________________ RELEASE VERSION : 1.10.15 RELEASE DATE : 2008/11/03 RELEASE BY : George Huang _______________________________________________________________________________ [CHECK-CODE] : 2600 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : athena:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-15 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.15 [PLM-NO] : [N/A] _______________________________________________________________________________ New Feature: ------------- N/A Bug Fixed: ------------- 1. When connecting some DES-1252 switches to a network with DHCP server, clients behind the switch will not get any IP from the DHCP server. 2. Smart switch can't get IP address from DHCP server on these routers of DIS-655 and DFL-800 when smart switch sends DHCP packet with source ip 192.168.0.1. Changed: ------------- N/A Note: ------------- N/A Known issues: ------------- N/A _______________________________________________________________________________ RELEASE VERSION : 1.10.14 RELEASE DATE : 2008/10/15 RELEASE BY : George Huang _______________________________________________________________________________ [CHECK-CODE] : 66A6 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : athena:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-14 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.14 [PLM-NO] : [N/A] _______________________________________________________________________________ New Feature: ------------- N/A Bug Fixed: ------------- 1. Fixed the 802.1x bug that switch is not able to authenticate clients. There is problem with 802.1X authentication. Users are able to do 802.1X authentication through switch in the beginning. But some of these users can not do 802.1X authentication again after few days. Changed: ------------- N/A Note: ------------- N/A Known issues: ------------- N/A _______________________________________________________________________________ RELEASE VERSION : 1.10.13 RELEASE DATE : 2008/06/13 RELEASE BY : George Huang _______________________________________________________________________________ [CHECK-CODE] : 2726 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : athena:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-13 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.13 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- N/A Bug Fixed: ------------- 1. Fix the bug that switch cannot get IP from DHCP server on these DIR655/DIR615 router. Changed: ------------- 1. Due to the lack of FLASH material. So add the FLASH driver support. - INTEL: JS28F160C3TC/JS28F160C3BC (2MB) Note: ------------- N/A Known issues: ------------- N/A _______________________________________________________________________________ RELEASE VERSION : 1.10.12 RELEASE DATE : 2008/04/30 RELEASE BY : George Huang _______________________________________________________________________________ [CHECK-CODE] : B25B [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : athena:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-12 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.12 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- N/A Bug Fixed: ------------- 1. The IGMP Snooping cannot execute the leave operation when enabling asymmetric VLAN. Changed: ------------- 1. Remove the workaround for passing UDP throughput test. Note: ------------- N/A Known issues: ------------- N/A Not bug: ------------- N/A _______________________________________________________________________________ RELEASE VERSION : 1.10.11 RELEASE DATE : 2008/04/10 RELEASE BY : George Huang _______________________________________________________________________________ [CHECK-CODE] : 0063 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-11 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.11 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1. Change Tail Drop Limits Register value for UDP multiple throughput issue. 2. Fix QOS priority issue. Changed: ------------- Note: ------------- Known issues: ------------- Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.10.10 RELEASE DATE : 2008/04/01 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : 6CC3 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-10 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.10 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1. Improve the low throughput under UDP multiple to one test. 2. LED no link after testing cable diagnostics funciton. Changed: ------------- Note: ------------- Known issues: ------------- Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.10.09 RELEASE DATE : 2008/03/06 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : A2A2 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-9 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.09 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1.Fix the issue that can't link when change fiber module from 100M to 1G. Changed: ------------- Note: ------------- Known issues: ------------- Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.10.08 RELEASE DATE : 2008/02/27 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : 471D [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-8 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.08 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1.Fix cable diagnostic bug. 2.Fix the bug of that port status will be sometimes detected down when SNMP polling. 3.Fixed GUI issue for QOS Queuing mechanism. Changed: ------------- Note: ------------- Known issues: ------------- Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.00.15 RELEASE DATE : 2008/01/29 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : CD8B [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-0-15 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.00.15 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1.This version is used to test Trunk issue on version 1.00.14. Changed: ------------- Note: ------------- Known issues: ------------- Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.10.07 RELEASE DATE : 2008/01/23 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : D390 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-07 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.07 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1.Change default QoS from WRR to Strict priority. 2.Delete port priority row form port setting page. Changed: ------------- Note: ------------- Known issues: ------------- Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.10.06 RELEASE DATE : 2008/01/15 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : 17AB [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-6 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.06 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1.[GUI issue] ============================== [TSDBUG #058] Opera 9.2 In Qos, our setting is DSCP-WRR, but the initial Qos page is 802.1p. 2.[SNMP issue] ============================== [TSDBUG #062] "igsVlanRouterPortList" value is wrong. [TSDBUG #063] "igsVlanRouterPortListTable" , the 'walk' value only show "igsVlanRouterPortListVlanId" 3.[IGS issue] ============================== [TSDBUG #057] When there are 256 VLAN groups, IGMP Snooping VLAN state cannot be disabled. [TSDBUG #059] when Querier State enable, Leave Time is 0, DUT leave time can not follow "(Robustness Variable-1)* Last member Query Interval+ Max respond time + Leave time" value to leave multicast group.( test it with mgen) [TSDBUG #060] when Querier State enable, Leave Time is 0, pc send join -> leave -> join by mgen, DUT no respond.(CPU LED no action) 4.Fix the bug that switch sometimes returns the down status when periodically getting PHY link status. *Add semaphore in hwdrv.c, add workarround in psscfg.c. 5.System crashed when SNMP packet size exceeded the local pkt buffer. Changed: ------------- Note: ------------- Known issues: ------------- [TSDBUG #061] in the SNMP Function Test, Private. When ip is 192.168.0.1/24 then gateway set to 192.168.1.254, the configuration still can be saved by snmp. [TSDBUG #064] two devices link to each other with fiber port, if we plug 100M miniGBic to fiber port then change 1G MiniGBIC to fiber port, we can find the fiber port cannot link. [TSDBUG #065] In QoS testing, if two ports transmit packets to the same and 802.1p Qos is the same, we can find the destination port receives rate is random. [TSDBUG #066] There are 7 fails in Spanning tree ANVL test. Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.00.14 RELEASE DATE : 2008/01/08 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : F72A [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-0-14 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.00.14 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1.Enable IGMP function (IGMP Query state enable) and we disable VLAN2 IGMP state, we find VLAN1 IGMP cannot transmit general query. 2.Can't turn off IGMP Snooping VLAN state when VLAN group number is 256. Changed: ------------- Note: ------------- 1. Base on 1.00.13 to fix bug. Known issues: ------------- Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.10.05 RELEASE DATE : 2008/01/07 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : 7785 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-5 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.05 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1.[Bcast control issue] ============================== [TSDBUG #053] Broadcast Storm Control function no work after change Threshold. 2.[802.1X issue] ============================== [TSDBUG #054] We set 802.1x enable and port 8 enable access control, then reboot DES2108, client PC can ping DUT with Unauthorized. 3.[IGS issue] ============================== [TSDBUG #055] We create two VLAN. VLAN1 (port2~8) VLAN2 (port1) We enable IGMP function (IGMP Query state enable) and we set port5 of the VLAN1 member to static router port and repeat set VLAN2 IGMP State to disable and enable then host transmit IGMP report and leave packets to VLAN2 of the device, we find the device CPU no respond. [TSDBUG #056] We enable IGMP function (IGMP Query state enable) and we disable VLAN2 IGMP state, we find VLAN1 IGMP cannot transmit general query. Changed: ------------- Note: ------------- Known issues: ------------- Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.10.04 RELEASE DATE : 2007/12/26 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : 63B6 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-4 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.04 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1.[QoS issue] ============================== [TSDBUG #013] In the 802.1P QoS Test, IEEE 802.1P QoS priority test result is fail in the 802.1P QoS Cross Chip Test. 2.[GUI issue] ============================== [TSDBUG #050] UI can set ip 223.255.0.x/24, and utility will recognize Invalid IP. Utility can set ip 192.168.0.1/16 gateway 192.168.0.255, but UI will recognize Invalid gateway. 3.[Asymmetric VLAN issue] ============================== [TSDBUG #051] Disable asymmetric vlan, delete vlan function cause DUT no respone. [TSDBUG #052] Disable asymmetric vlan, create a vlan with no member, DUT no respone. Changed: ------------- Add IGMP Query state IGMP Query state enable: 1.DUT will send general query. 2.When DUT receive leave packets, DUT will send spcial Query and leave time must cost "(Robustness Variable-1)* Last member Query Interval+ Max respond time + Leave time" value to leave multicast group. IGMP Query state disable: 1.DUT won't send general query. 2.When DUT receive leave packets, DUT won't send spcial Query and leave time just cost "IGMP Leave time" value to leave multicast group. Note: ------------- Known issues: ------------- Not bug: ------------- [TSDBUG #046] Can't check for newer versions of stored pages automatically. _______________________________________________________________________________ RELEASE VERSION : 1.10.03 RELEASE DATE : 2007/11/29 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : 151B [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-3 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.03 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1.[IGMP issue] ============================== [TSDBUG #025] We find IGMP Snooping Query Interval function no work. [TSDBUG #026] We find IGMP Snooping Max response Time function no work. [TSDBUG #027] We find IGMP Snooping Last Member Query Interval function no work. [TSDBUG #028] We find the IGMP Snooping Robustness Variable Function no work. 2.[Asymmetric VLAN issue] ============================== [TSDBUG #044] If we enable Asysmmetric VLAN funciton then set port2 to VLAN2 and Port2 PVID set to 2, we find the port2 VID still is 2 after we delete VID2 VLAN. Changed: ------------- Note: ------------- Known issues: ------------- Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.00.13 RELEASE DATE : 2007/11/27 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : B731 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-0-13 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.00.13 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1.Fix the LED shut down bug. *Function HW_SetBcastCtrl_Rate in hwdrv.c, a variable is not initiated. Changed: ------------- Note: ------------- Known issues: ------------- Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.00.12 RELEASE DATE : 2007/11/26 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : 962F [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-0-12 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.00.12 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1.Fix issues in IGMP Snooping. - Send General Query by Query interval. - When leave message recieve, follow standard rule to send specific query packets. - Fix IGMP function enable that cause DUT ping no response. - If users utilize IGMP Snooping with the topology like or similar to Figure 1, the network may cause ping no response when router timeout. ______________ ___________ ___________ ______________ | | | | | | | | | Media Center |------| DUT1 |------| DUT2 |------| IGMP Host | |_____________ | |___________| |___________| |_____________| Figure 1. 2.Improve the performance of DISCOVERY/SNMP Trap. - Use SNMP Trap Settings or Trap Settings for SmartConsole, will cause delay of PING response response. Now check port trap event (every time 4 ports) every 3 seconds. 3.Fix Logic in issue. - When log in the device control interface in web browser , then reset device and refresh web browser. User won't need password to log in the web. Changed: ------------- Note: ------------- 1. This version is base on 1.00.11 only change patch of sdk/PSS/mainDrv/src/prestera/tapi/bridge/gtBrgFdb.c Known issues: ------------- Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.00.11 RELEASE DATE : 2007/10/31 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : 9147 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-0-11 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.00.11 [PLM-NO] : [N/A] _____________________________________________________________________________ New Feature: ------------- Bug Fixed: ------------- 1. VLAN groups which exceed 64th has no work. **SDK limits maximum number of VLAN groups is 64, but datasheet of chip is 256. We modify gtBrgVlan.h from 64 to 256. 2. If users add vlan to 256 groups, system will crash. **Modify variable type from UI8_T to UI16_T. Changed: ------------- Note: ------------- 1. This version is beta version by case. Modify from version 1.10.02 to take off new functions we add in phase II. Known issues: ------------- Not bug: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.10.02 RELEASE DATE : 2007/10/02 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : AD05 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-2 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.02 [PLM-NO] : [N/A] _____________________________________________________________________________ New Features ------------- 1. DSCP function. Bug Fixed: ------------- 1.[GUI issue] ============================== [TSDBUG #038] We find the VLAN setting Page error when we want to create new VID VLAN. [TSDBUG #039] We find the Smart Wizard web page cannot be readed finish via Netscape and Firefox brower. [TSDBUG #042] We can set the same Mac address and VID to static Mac table. [TSDBUG #015] Smart Wizard (Password Settings)When password include "blank", DUT can cot login.But setting from "Password Access Control" page, is ok. 2.[Cable Diagnostic issue] ============================== [TSDBUG #040] If we test 100M ports of DUT via cable diagnostic function, we find the 100M port link/Act no link after test diagnostic function. **SDK bug. Opal have no page register, but SDK have no check. [TSDBUG #008] If we set port13 status to disable then test port13 Cable Diagnostic, we find the DUT no respone. **Add check in post.c, disabled ports cannot test. 3.[Trunk issue] ============================== [TSDBUG #041] If two device uplink via trunk port(25~28), we find discovery one device via smartconsole utility. **PCL rule bug. Have not bind trunk ID into PCL ID. 4.[Management VLAN issue] ============================== [TSDBUG #005] If we create port1~8 to VID2 (Not Management VLAN) and then we delete VID2 VLAN , we find the Switch no respond. **System layer shift bitmap error. 5.[Fiber issue] ============================== [TSDBUG #014] Two fiber port transmit packets each other in 1000M Fiber Auto mode, we can find two fiber port can not receive packets. 6.[NOT BUG] ============================== [TSDBUG #034] We find the VoIP Packets is highest priority not high priority, please modify the Auto VoIP describe. [TSDBUG #036] D-LINK request the Auto VoIP function must support SIP,MGCP, SCCP include others VoIP protocol packets(i.e RTP/RTCP/..). [TSDBUG #033] If we logout the Web Control UI, we find just only IE Brower show logout warning message, other Web Browers cannot show this warning message. **Limits of browser. [TSDBUG #009] If we test problem Cable or disable port Cable Diagnostic funciton, we find must cost above 15 sec just can get result. **It must spends a lot of time. [TSDBUG #020] If we detect port13 Cable Diagnostic and set Port13 speed to 100M Full and 10M Half Force mode then uplink to other Giga DUT via 1m and 120m UTP cable, we find detect result Cable Length (Show N/A) fail **Cable must link on 1000M speed. [TSDBUG #024] If we detect port13 Cable Diagnostic and Port13 link speed is 1000M Full via 130m UTP cable, we find detect result Cable Length (show N/A) fail. **Cable is out of range(100M), so the test status is not stable. Changed: ------------- 1.Remove Auto VoIP function. Known issues: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.10.01 RELEASE DATE : 2007/09/06 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : C82C [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-1 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.01 [PLM-NO] : [N/A] _____________________________________________________________________________ New Features ------------- 1. Asymmetric VLAN. Bug Fixed: ------------- 1.[GUI issue] ============================== [TSDBUG #001] If we change Switch Password to "~!@#$%^&*()_+", we will find the new password cannot login to Switch Web UI and System Name will be change to "6%28%29_%2B". [TSDBUG #002] If the Switch Web UI login timeout then we select "SmartWizard", we cannot find login timeout page then WEB UI show login page. [TSDBUG #006] We find Login timeout page show problem in the Smart Wizard Page. (Size asymmetric) [TSDBUG #018] If we create 256 VLAN Groups and eable IGMP Function then move VLAN Settings of IGMP Snooping table scoll bar, we find the VLAN State GUI show error. [TSDBUG #037] Smart Wizard shoud be "configure", not cinfigure. 2.[Forwarding Table issue] ============================== [TSDBUG #004] If we search Port dynamic forwarding table, we fine the Web Control UI auto logout. 3.[IP setting issue] ============================== [TSDBUG #007] These setting should be rejected by DUT 127.168.0.1/24 224.255.0.2/24 172.255.0.255/24 These setting should be accepted by DUT 223.255.0.2/24 192.168.0.1/16 and Gateway 192.168.0.255 4.[Trust Host issue] ============================== [TSDBUG #010] We find the same Host IP cannot be duplicated, but if we set the same IP Mask (i.e. 192.168.0.2/24 and 192.168.0.3/24) can be duplicated. **Add check in post.c. [TSDBUG #030] We find the trust host IP address cannot set to 223.x.x.x/24. **Modify function "convert_val_to_ip" in post.c. 5.[VLAN issue] ============================== [TSDBUG #017] If we create 257 VLAN groups (Over max VLAN groups setting), the Web UI doesn't show any warning message then we create VID 257 VLAN again, we find the Switch no respond. 6.[Auto VOIP issue] ============================== [TSDBUG #035] We find Auto VoIP MGCP default Port just only support 2427. RFC 3435 . by the Call Agents, to the default MGCP port for gateways, 2427. . by the Gateways, to the default MGCP port for Call Agents, 2727. **Solve by port check. 7.[NOT BUG] ============================== [TSDBUG #012] We recommend "excluding" change to "Excluding below: **Not modify!!D-Link confirmed result. [TSDBUG #011] Please change "can not" to "cannot". (D-LINK request before) **Follow D-Link's request. Please refer to pop up message. [TSDBUG #003] If we detect port9 (Control PC Uplink Port) via Cable Diagnostic Function, we find the Cable Diagnostic no detect result. **Test port will be link down. [TSDBUG #009] If we test problem Cable or disable port Cable Diagnostic funciton, we find must cost above 15 sec just can get result. **Must wait test complete then get value from register. [TSDBUG #019] If we set port17 of DUT speed to 100M Half force mode then uplink to another switch 100M Half force mode port, we find port17 cable diagnostic check result pair1 fail. **Partner must auto or 10M force mode. [TSDBUG #021] If we detect port13 Cable Diagnostic and Port13 link speed is 1000M Full via 1m and 120m UTP cable, we find detect result Cable Length (1m show <50m, 120m show 80m~110m) fail. **Normal cable length only can be shown range. [TSDBUG #022] If we detect the authorized port cable, we find the cable diagnostic detect result fail. **Power saving bug. [TSDBUG #023] If we detect port13 Cable Diagnostic and Port13 link link to 100M HUB via 1m UTP cable, we find detect result Pair test (Pair3 and 4 show short) and Cable Length (show N/A) fail. If we dtetct port13 Cable Diagnostic and Port13 link link to 100M NIC via 1m UTP cable, we find detect result Pair test (Pair3 and 4 show Open) and Cable Length (show N/A) fail. **Due to the design of HUB's and NIC's hardware, test results are different. [TSDBUG #031] If we set trusted host to 192.168.1.1/24 then our control client IP address is 192.168.0.33/24 and 192.168.1.33/24, we cannot control the Switch. **It's utility bug, not trust host bug. Changed: ------------- Known issues: ------------- [TSDBUG #013] In the 802.1P QoS Test, IEEE 802.1P QoS priority test result is fail in the 802.1P QoS Cross Chip Test. _______________________________________________________________________________ RELEASE VERSION : 1.10.00 RELEASE DATE : 2007/08/01 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : D61F [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-10-0 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.10.00 [PLM-NO] : [N/A] _____________________________________________________________________________ New Features ------------- 1. Management VLAN. 2. STP, Edge, Disable modes for per port settings in Spanning Tree function. 3. Trusted Host. 4. Auto VoIP. 5. Cable Diagnoistic. 6. Update Device Information page with scroll bar style. 7. F/W upgrade/configuration in SNMP browser. 8. Hyperlink of D-Link support in banner. 9. Smart Wizard for the initial settings. 10.Refine wording about pop-up message. 11.Don't show the model name before logining GUI. Bug Fixed: ------------- 1. Looping on the solution of DIAMOND + OPAL 2. Remote access control through Web GUI, and the URL only shows IP address instead of file path. 3. Static MAC function:If MAC Address which user key in all are random code, system will crash. 4. It must shows correct CPU status when uses SNMP brower, corrects the index info 64. 5. Remove the PHY diag from initialization in hwdrv.c. 6. Fix QoS abnormal rate issue on DIAMOND ports. 7. Fix the issue of host timeout not synchronous in IGMP Snooping. Macro define issue for IGS_VIDX_HASH_NUMBER, IGS_MCAST_FWD_TABLE_SIZE IGS_VIDX_HASH_NUMBER 256 for 28/52/28P IGS_VIDX_HASH_NUMBER 512 for 16/24/48 8. Back config time out issue. 9. Fix "Marvell DX port receive LLDP packet cause device resend the same LLDP packets to network problem" issue. Changed: ------------- 1.SDK version update from v1.4.1 to v1.6.8. Known issues: ------------- _______________________________________________________________________________ RELEASE VERSION : 1.00.10 RELEASE DATE : 2007/08/10 RELEASE BY : Marc Li _______________________________________________________________________________ [CHECK-CODE] : 7642 [CHECKSUM] : [N/A] [PART-NO] : [N/A] [CVS] : -Root : cvsserver:/WSS -Module : platform/DES1252 -TAG : DES1252-REL1-0-10 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : 1.00.10 [PLM-NO] : [N/A] _____________________________________________________________________________ New Features ------------- Bug Fixed: ------------- 1. Base on f/w:1.00.09 fix "Marvell DX port receive LLDP packet cause device resend the same LLDP packets to network problem" issue. Changed: ------------- Known issues: ------------- _______________________________________________________________________________ RELEASE VERSION : v1.00.09 RELEASE DATE : RELEASE BY : Denis Hsieh _______________________________________________________________________________ [CHECK-CODE] : 75E1 [CHECKSUM] : [N/A] [PART-NO] : [CVS] : -Root : cvsserver:/wss -Module : platform/DES1252 -TAG : DES1252-REL1-0-9 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : [N/A] _______________________________________________________________________________ Bug Fixed: ------------- 1.Remote access bug. Note: This is beta version for TSD, unofficial release. Poyi verification date is 2007/04/23 _______________________________________________________________________________ RELEASE VERSION : v1.00.08 RELEASE DATE : RELEASE BY : Denis Hsieh _______________________________________________________________________________ [CHECK-CODE] : [CHECKSUM] : [N/A] [PART-NO] : [CVS] : -Root : \\sdserver\SW-Project\cvsroot\Release\TP -Module : Websm_SW\Marvell 98DX106-B0+88E6092\D-Link\DES1252 -TAG : DES1252-REL1-0-8 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : [N/A] _______________________________________________________________________________ Bug Fixed: ------------- 1.Index 604 CPU Port status show error. 2.For RISC architecture, this value have to be N-Bytes Alignment N dependends on the Architecture. For ARM/MIPS N=4. Note: This is beta version for TSD, unofficial release. _______________________________________________________________________________ RELEASE VERSION : v1.00.07 RELEASE DATE : 2006/07/18 RELEASE BY : Ben Lin _______________________________________________________________________________ [CHECK-CODE] : 136E [CHECKSUM] : [N/A] [PART-NO] : 1251DES12526000 [CVS] : -Root : \\sdserver\SW-Project\cvsroot\Release\TP -Module : Websm_SW\Marvell 98DX106-B0+88E6092\D-Link\DES1252 -TAG : DES1252-REL1-0-7 [TMPL-VER] : [N/A] [ECN-NO] : [N/A] [TP-TIME] : [N/A] [FW-VER] : [N/A] _____________________________________________________________________________ New Features: ------------- N/A Bug Fixed: ------------- ___________________________issue________________________________#_of_issue______ 1. [Spanning Tree issue] 1 2. [Trunk issue] 4 3. [IGMP issue] 2 4. [Mini-GBIC capability issue] 1 5. [802.1X issue] 4 6. [Other issue] 2 ******************************************************************************** Total: 14 Description: 1. [Spanning Tree issue] .[TSDBUG #115] In the Spanning Tree Function Test, If we loop two Opal with port 1~16, we can find the device loop. 2. [Trunk issue] .[TSDBUG #100] In the Trunk Function Test, If two devices uplink with trunk ports then transmit Unicast Packets and when the trunk group all unlink, we can find the trunk group forwarding table doesn¡¦t aging. .[TSDBUG #117] In the Trunk Function Test, If two devices uplink with trunk ports then transmit BPDU Packets, we can find the trunk group (46~52) loop. .[TSDBUG #119] In theTrunk Function Test, If four devices uplink with trunk ports then we discovery the device with SmartConsloe Utility, we just can discovery one device in some devices. .[TSDBUG #120] In the Trunk Function Test, If four devices uplink with trunk ports then we transmit Unicast packets to each other with Trunk groups; we can find some ports of the devices cannot receive any packets. 3. [IGMP issue] .[TSDBUG #106] In the IGMP Funciton Test, if we enable IGMP functuion of the device then send IGMP v3 report packets to the device, we can find the IGMP v3 leave packets no work. .[TSDBUG #108] In the IGMP Funciton Test, if we enable IGMP functuion and send report packets to the another device with combo copper ports and we send multicast media packets then change combo copper port to fiber port, we can find the fiber port cannot forward media frames. *** I've fixed this bug which fast join/laeve cause sometimes FAIL in router port's join. I added the mechanism which add router ports in multi-groups whenever if found this multicast IP entry is exist or not. *** .[TSDBUG #129] In the IGMP Function MOD Test, If we change MOD Channel, sometime we can find the router port doesn¡¦t join multi-groups. *** In Future implement we have the note : Sanity check. If packet arrives with a reserved destination IP as well as having packet type as V1, V2 or V3 report then classify this packet as (Illegal) data packet. Dont learn. It would get 2 lower byte from Group MAC address (i.e. 01-00-5E-00-00-02->00-02) to check the range if in 2-255 and identify packet type, do not learn if IGMP v1, v2, v3 Report packet. *** .[TSDBUG #131] In the IGMP Function Test, we can find 225.0.02~225.0.0.9 multi-Group cannot join. .[TSDBUG #134] In the IGMP Function MOD Test, if we reboot the device, we can find the IGMP leave time setting doesn¡¦t work. 4. [Mini-GBIC capability issue] *** About 100M fiber modules, some modules are link well(like Agilent), but some modules are slow to link up(about 10 sec, like CORETEK and APAC) *** .[TSDBUG #101] There are Mini GBIC Compatibility issue: APAC LM38-A3S-TC-N (Multi Mode) Mini GBIC cannot link. CORETEK CT-0155NSP-MB2L (Multi Mode) Mini GBIC sometimes cannot link. JDS Uniphase JSM-21S3AA3 (Multi Mode) Mini GBIC will link to 100M Full duplex mode. 5. [802.1X issue] .[TSDBUG #126] In the 802.1X Function Test, If we unplug and plug the radius server port, we can find the client cannot authorize form the radius server. .[TSDBUG #127] In the 802.1X Function Test, If the client authorizes form the radius server, we can find the radius server receive a lot of packets form the device. .[TSDBUG #128] In the 802.1X Function Test, If we enable 802.1x function and set port control status enable then we disable the 802.1x function with SNMP, we can find the 802.1x port control status stil enable. .[TSDBUG #138] In the 802.1x web UI confirm "key" check function fail. 6. [Other issue] .[TSDBUG #122] Sometime we can find the Web UI cannot refash function setting page, we must delete IE temp. *** Disabling MAC & PHY transmit in system initialization will cause this problem. To solve this issue, we only need to disable MAC transmit. *** .[RDBUG] Fiber port can't link up via fiber cable uplink between two DUT. Changed: ------------- N/A Known issues: ------------- ___________________________issue________________________________#_of_issue______ 1. [Port Setting issue] 5 2. [Forwarding Table issue] 5 3. [Spanning Tree issue] 2 4. [Broadcast Transmit issue] 2 5. [QoS issue] 2 6. [IGMP issue] 1 7. [SNMP issue] 1 8. [Firmware and Config Backup issue] 1 9. [Mirror issue] 2 10.[Other issue] 6 ******************************************************************************** Total: 27 Description: 1. [Port Setting issue] *** Due to port setting change state is slow, cause CPU response packet will lost. Suggestion: When use SNMP UI to control to device port, don't change the link port of itself. *** . [TSDBUG #29] In the SNMP UI¡§Port setting¡¨test, if we control the SNMP UI of the device with Intel PRO/1000MT NIC then we set the control port speed to the 100M Full/Half Force mode, we can find the Intel PRO/1000MT NIC cannot link.(PS: the Intel PRO/1000MT NIC speed is Auto Mode) *** Current version NOT surpport flow control *** . [TSDBUG #37] In the Web UI¡§Port setting¡¨Test, if we enable flow control function of the device and we transmit packets to test flow control with the smartbit (flow control disable), we find test result flow control still enable. *** Current version NOT surpport flow control *** . [TSDBUG #38] In the Web UI¡§Port setting¡¨Test, if we enable flow control function of the device and use two ports transmit short packets to one port of the device, we can find the port transmit rate is wrong. *** Current version NOT surpport flow control *** . [TSDBUG #41] In the Flow Control Test, if we flow control enable and the port49~51 transmit packets to the port52 then port48 transmit packets to the port52, we can find port49 and port50 cannot receive pause frame. *** OPAL port doesn't support the function of disabling auto MDI/MDIX. *** .[TSDBUG #121] In the Port Setting Function Test, if the 100M Ports of the device set to force mode, we can find the 100M Portsl Auto MDI/MDIX doesn¡¦t disable.(1000M Ports of the device OK!) 2. [Forwarding Table issue] *** (Chip limitation) MVL offer white paper, Automatic Aging in 98DX107 and 88E6095, MV-TBD-00 Rev. 0.1 to explain this *** . [TSDBUG #27] In the¡§Forwarding Table¡¨test, we find the diamond DX106 and Opal of the device Aging time are not synchronization. . [TSDBUG #64] In "Forwarding Test", we cannot search any Mac address in the trunk port forwarding table. *** Reason: Our forwarding table can only keep 512 MACs *** . [TSDBUG #96] In the Web UI Forward table test, if we add 100 Mac address to the static mac table, then we search forwarding table, we can search 420 Mac Address in the forwarding table. *** Reason: Trunk port learning MAC is static MAC, currently we do not show static MAC on forwarding table *** . [TSDBUG #97] In the Web UI Forward table test, if we uplink two device with trunk port (port1~4), then we transmit 100 Mac address from device1 to the device2 and 4 trunk ports of the device2 all receive packets form device, we just only can search port1 forwarding table. .[TSDBUG #118] In the Dynamic Forwarding Table Function Test, we can find the forwarding table just can search 511 Mac Address. 3. [Spanning Tree issue] *** The issue doesn't be described in IEEE 802.1D spec. We may come out a better solution in the future. *** . [TSDBUG #53] In "Spanning Tree function" testing, we can find in the same trunk group loop, the device cannot block. *** Still have 11 fails, Timing issue *** . [TSDBUG #92] In the ¡§Spanning tree ANVL test¡¨, test results have 14 fails. 4. [Broadcast Transmit issue] *** Buffer issue: Test OK on 8 10/100 ports + 4 giga ports *** . [TSDBUG #47] In "Broadcast Transmit" testing, if we transmit broadcast packets, we find some ports of the device receive rate no full wire speed. *** Buffer issue: Test OK on 8 10/100 ports + 4 giga ports Chip behavior: All source ports are competiting the shared resource and cause the unbalance distribution. The symptom will not happen on random size of traffic. *** . [TSDBUG #77] In "Multicast and Broadcast transmit" testing, we can find some ports can not receive source port packets.(Fixed packets length) 5. [QoS issue] *** MVL can expalin when send fix length packet, some port may always scramble the buffer, use random size will not have this issue. Refer to "Congested Transmit Queue Bandwidth Division", MV-S300420-00 Rev. A. *** . [TSDBUG #46] In "QoS" testing, if two ports transmit packets to the same and 802.1p Qos is the same, we can find the destination port receives rate is random. *** Marvell chip behavior, we may fix the issue in next phase. *** .[TSDBUG #125] In the802.1P QoS Test, IEEE 802.1P QoS priority test result is fail in the 802.1P QoS Cross Chip Test. Highest : High : Middle : Low ¡Ü 4 : 4 : 2 : 1 not 8 : 4 : 2 : 1. 6. [IGMP issue] .[TSDBUG #105] In the IGMP Funciton Test, if we disable group interval and enable IGMP functuion of the device then discovery the device, we can find the IGMP v1 leave packets no work. *** S/W issue, may fix on next phase. *** .[TSDBUG #136]In the IGMP Function Test, if we set router timeout to 60 sec, sometime we can find the dynamic router port timeout cost about 120 sec. *** S/W issue, may fix on next phase. *** .[TSDBUG #137]In the IGMP Function Test, if we transmit multicast groups IGMP V2 report form the win2000 client to the device, we can find the device support max multicast groups are 63. (If we use winxp IGMP V3 report, test result is OK) 7. [SNMP issue] .[TSDBUG #114] In the SNMP Function Test, Private When IP address and Gateway are different with subnet mask, the configuration still can be saved by snmp (GUI is OK). 8. [Firmware and Config Backup issue] *** The test is OK in Win2000 environment, but is failed in WinXP *** . [TSDBUG #75] In "Firmware and Config Backup" testing, Firmware and Config File cannot be saved, if waiting time is too long (over 5-10 sec.approximately), when we want to save Config File Name and select the saved path. 9. [Mirror issue] *** Marvell SDK issue, we may fix the issue in next phase. *** .[TSDBUG #123] In the Mirror Function Test, if we set all ports to source port and mirror both then we set all source ports to none and set por2 mirror TX, we can find the mirror port can mirror port2 TX and RX. *** Marvell SDK issue, we may fix the issue in next phase. *** .[TSDBUG #124] In the Mirror Function Test, if we set Port1 to Target then set port2 to Mirror TX source port, we can find port2 transmit broadcast packets and port1 cannot receive any packets. *** Marvell SDK issue, Now mirror function conflicts with VLAN function *** .[TSDBUG #130]In the Mirror Function Test, if we set port1 is target port in the VLAN1 then set source port to port2 in the VLAN2, we can find if port2 unlink then port3 in the VLAN2 transmit broadcast packets and the port1 target port can receive port3 transmit packets 10.[Other issue] *** Buffer issue: Test OK on 8 10/100 ports + 4 giga ports *** . [TSDBUG #44] If the device transmit packets form Dianomd (Port49) to the Opal (Port1) and the Port1 transmit packets to the Port2 of the device, we will find the Port2 receive rate too slow. *** Buffer issue: Test OK on 8 10/100 ports + 4 giga ports *** . [TSDBUG #69] If we use one giga port and port1~8 transmit packets to each other, we can find the giga port have loss packets problem. Loss rate:0.0008%*** (buffer tuning, still test by MVL)*** *** Buffer issue *** .[TSDBUG #103] There are loss packets problem in the 100M Full Duplex X-Stream Test. Max loss rate: 0.07% .[TSDBUG #104] There are loss packets problem in the Half Duplex Unicast Transmit Test. Max loss rate: 92.66% .[TSDBUG #109] In the 100M Full Duplex Mode ASTII Forwarding Test, we find the test result have loss packets problem. *** Chip behavior: Caused by collision congestion. *** .[TSDBUG #116] If two 100M fiber ports of the device transmit packets to each other at the same time in the 100M Half Duplex Force Mode, we can find one 100M fiber port of the device cannot receive packets. .[TSDBUG #133]In the Web Brower Test, we can the SNMP, QoS and Dynamic Forwarding Table function page UI display error with Opera Brower V8.53. *** Chip behavior: Caused by collision congestion. *** .[TSDBUG #132]In the Statistics Function Test, if we transmit packet length: 10240 to the device, we can find the statistics function cannot detect frame too long. *** S/W issue, may fix on next phase. *** .[TSDBUG #135]In the Trap Function Test, if the Mini GBIC plugs in the device, we can find the device reboot trap doesn¡¦t work. Note: N/A _____________________________________[END]______________________________________