-------------------------------------------------------------------------------- -- --------------------------- Revision ---------------------------------------- -- Date Version Author Chanage Description -- -- 2015/11/20 4.10.002 D-Link 1. Port Auto Downgrade. -- 2. Legacy PD. -- -- 2015/11/06 4.10.001 D-Link 1. For formal release with firmware 4.10.001 -- -- 2015/09/25 4.00.B017 D-Link 1. Add DHCPRetryTimes object. -- 2015/09/18 4.00.B016 D-Link 1. Modify cableDiagPairStatus object. -- 2. Modify doSCtrlDisplayState object. -- -- 2014/08/18 4.00.015 D-Link 1. Update mib version to 4.00.015. -- -- 2014/07/29 4.00.B014 D-Link 1. Add poePortLegacyPDDetect object on DGS-1210-28P. -- -- 2014/05/12 4.00.001 D-Link Initial version. -- -- -------------------------- Revision End ------------------------------------- -------------------------------------------------------------------------------- DGS-1210-10P_CX DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, enterprises, IpAddress, Integer32, Unsigned32, TimeTicks, Counter32 FROM SNMPv2-SMI InetAddress FROM INET-ADDRESS-MIB InterfaceIndex,InterfaceIndexOrZero,ifIndex FROM IF-MIB SnmpAdminString,SnmpEngineID,SnmpSecurityLevel FROM SNMP-FRAMEWORK-MIB dot1dBridge, dot1dBasePortEntry, dot1dBasePort FROM BRIDGE-MIB RowStatus, TruthValue, DisplayString, TEXTUAL-CONVENTION, MacAddress FROM SNMPv2-TC AddressFamilyNumbers FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB; d-link OBJECT IDENTIFIER ::= { enterprises 171 } dlink-products OBJECT IDENTIFIER ::= { d-link 10 } dlink-DGS12XXSeriesProd OBJECT IDENTIFIER ::= { dlink-products 76} dgs-1210-10p OBJECT IDENTIFIER ::= { dlink-DGS12XXSeriesProd 18 } dgs-1210-10pcx OBJECT IDENTIFIER ::= { dgs-1210-10p 1 } VlanIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095 then it represents a VLAN with scope local to the particular agent, i.e. one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q but it is convenient to be able to manage them in the same way using this MIB." SYNTAX Unsigned32 PortList ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'." SYNTAX OCTET STRING BridgeId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to refer to a bridge in a unique fashion (typically, the numerically smallest MAC address of all ports on the bridge). Several objects in this MIB module represent values of timers used by the Spanning Tree Protocol. In this MIB, these timers have values in units of hundreths of a second (i.e. 1/100 secs). These timers, when stored in a Spanning Tree Protocol's BPDU, are in units of 1/256 seconds. Note, however, that 802.1D-1990 specifies a settable granularity of no more than 1 second for these timers. To avoid ambiguity, a data type is defined here as a textual convention and all representation of these timers in this MIB module are defined using this data type. An algorithm is also defined for converting between the different units, to ensure a timer's value is not distorted by multiple conversions." SYNTAX OCTET STRING (SIZE (8)) Timeout ::= TEXTUAL-CONVENTION DISPLAY-HINT "d4" STATUS current DESCRIPTION "A STP timer in units of 1/100 seconds To convert a Timeout value into a value in units of 1/256 seconds, the following algorithm should be used: b = floor( (n * 256) / 100) where: floor = quotient [ignore remainder] n is the value in 1/100 second units b is the value in 1/256 second units To convert the value from 1/256 second units back to 1/100 seconds, the following algorithm should be used: n = ceiling( (b * 100) / 256) where: ceiling = quotient [if remainder is 0], or quotient + 1 [if remainder is non-zero] n is the value in 1/100 second units b is the value in 1/256 second units Note: it is important that the arithmetic operations are done in the order specified (i.e., multiply first, divide second)." SYNTAX INTEGER RmonStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The status of a table entry. Setting this object to the value invalid(4) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries currently not in use. Proper interpretation of such entries requires examination of the relevant RmonStatus object. An existing instance of this object cannot be set to createRequest(2). This object may only be set to createRequest(2) when this instance is created. When this object is created, the agent may wish to create supplemental object instances with default values to complete a conceptual row in this table. Because the creation of these default objects is entirely at the option of the agent, the manager must not assume that any will be created, but may make use of any that are created. Immediately after completing the create operation, the agent must set this object to underCreation(3). When in the underCreation(3) state, an entry is allowed to exist in a possibly incomplete, possibly inconsistent state, usually to allow it to be modified in multiple PDUs. When in this state, an entry is not fully active. Entries shall exist in the underCreation(3) state until the management station is finished configuring the entry and sets this object to valid(1) or aborts, setting this object to invalid(4). If the agent determines that an entry has been in the underCreation(3) state for an abnormally long time, it may decide that the management station has crashed. If the agent makes this decision, it may set this object to invalid(4) to reclaim the entry. A prudent agent will understand that the management station may need to wait for human input and will allow for that possibility in its determination of this abnormally long period. An entry in the valid(1) state is fully configured and consistent and fully represents the configuration or operation such a row is intended to represent. For example, it could be a statistical function that is configured and active, or a filter that is available in the list of filters processed by the packet capture process. A manager is restricted to changing the state of an entry in the following ways: To: valid createRequest underCreation invalid From: valid OK NO OK OK createRequest N/A N/A N/A N/A underCreation OK NO OK OK invalid NO NO NO OK nonExistent NO OK NO OK In the table above, it is not applicable to move the state from the createRequest state to any other state because the manager will never find the variable in that state. The nonExistent state is not a value of the enumeration, rather it means that the entryStatus variable does not exist at all. An agent may allow an entryStatus variable to change state in additional ways, so long as the semantics of the states are followed. This allowance is made to ease the implementation of the agent and is made despite the fact that managers should never exercise these additional state transitions." SYNTAX INTEGER { valid(1), createRequest(2), underCreation(3), invalid(4) } LldpManAddress ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The value of a management address associated with the LLDP agent that may be used to reach higher layer entities to assist discovery by network management. It should be noted that appropriate security credentials, such as SNMP engineId, may be required to access the LLDP agent using a management address. These necessary credentials should be known by the network management and the objects associated with the credentials are not included in the LLDP agent." SYNTAX OCTET STRING (SIZE (1..31)) Ipv6Address ::= TEXTUAL-CONVENTION DISPLAY-HINT "2x:" STATUS current DESCRIPTION "This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order." SYNTAX OCTET STRING (SIZE (16)) -- ----------------------------------------------------------------- -- -- groups in the MIB -- ----------------------------------------------------------------- -- companySystem OBJECT IDENTIFIER ::= { dgs-1210-10pcx 1 } companyIpifGroup OBJECT IDENTIFIER ::= { dgs-1210-10pcx 2 } companyTftpGroup OBJECT IDENTIFIER ::= { dgs-1210-10pcx 3 } companyMiscGroup OBJECT IDENTIFIER ::= { dgs-1210-10pcx 4 } companyRSTP OBJECT IDENTIFIER ::= { dgs-1210-10pcx 6 } companyDot1qVlanGroup OBJECT IDENTIFIER ::= { dgs-1210-10pcx 7 } companyLA OBJECT IDENTIFIER ::= { dgs-1210-10pcx 8 } companyStaticMAC OBJECT IDENTIFIER ::= { dgs-1210-10pcx 9 } companyIgsGroup OBJECT IDENTIFIER ::= { dgs-1210-10pcx 10 } companyQoSGroup OBJECT IDENTIFIER ::= { dgs-1210-10pcx 12 } companyTrafficMgmt OBJECT IDENTIFIER ::= { dgs-1210-10pcx 13 } companySecurity OBJECT IDENTIFIER ::= { dgs-1210-10pcx 14 } companyACLGroup OBJECT IDENTIFIER ::= { dgs-1210-10pcx 15 } companySyslog OBJECT IDENTIFIER ::= { dgs-1210-10pcx 16 } companyLBD OBJECT IDENTIFIER ::= { dgs-1210-10pcx 17 } companyMirror OBJECT IDENTIFIER ::= { dgs-1210-10pcx 18 } companySNTPSetting OBJECT IDENTIFIER ::= { dgs-1210-10pcx 20 } companyVoiceVlan OBJECT IDENTIFIER ::= { dgs-1210-10pcx 21 } companyPoEGroup OBJECT IDENTIFIER ::= { dgs-1210-10pcx 22 } companyAuthGroup OBJECT IDENTIFIER ::= { dgs-1210-10pcx 23 } companyLLDPSetting OBJECT IDENTIFIER ::= { dgs-1210-10pcx 24 } companySNMPV3 OBJECT IDENTIFIER ::= { dgs-1210-10pcx 25 } companyAutoSurveillanceVlan OBJECT IDENTIFIER ::= { dgs-1210-10pcx 26 } companyTraps OBJECT IDENTIFIER ::= { dgs-1210-10pcx 27 } companyGreenSetting OBJECT IDENTIFIER ::= { dgs-1210-10pcx 31 } companyTimeRangeMgmt OBJECT IDENTIFIER ::= { dgs-1210-10pcx 32 } companyStaticMcast OBJECT IDENTIFIER ::= { dgs-1210-10pcx 35 } companyCableDiagnostic OBJECT IDENTIFIER ::= { dgs-1210-10pcx 37 } companyRMON OBJECT IDENTIFIER ::= { dgs-1210-10pcx 47 } companyNeighbor OBJECT IDENTIFIER ::= { dgs-1210-10pcx 50 } companydot3azEEE OBJECT IDENTIFIER ::= { dgs-1210-10pcx 52 } companyDHCPRelay OBJECT IDENTIFIER ::= { dgs-1210-10pcx 61 } companyDHCPLocalRelay OBJECT IDENTIFIER ::= { dgs-1210-10pcx 62 } companyDHCPv6Relay OBJECT IDENTIFIER ::= { dgs-1210-10pcx 63 } companyMldsGroup OBJECT IDENTIFIER ::= { dgs-1210-10pcx 88 } companyDoSCtrl OBJECT IDENTIFIER ::= { dgs-1210-10pcx 99 } -- ---------------------------------------------------------------- -- -- ------------------------------------------------------------------ -- companySystem -- ------------------------------------------------------------------ sysSwitchName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) �V + _ = ." ::= { companySystem 1 } sysHardwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "Version number of the Hardware." DEFVAL { "" } ::= { companySystem 2 } sysFirmwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "Version number of the Firmware." DEFVAL { "" } ::= { companySystem 3 } sysLoginTimeoutInterval OBJECT-TYPE SYNTAX Integer32 (3..30) MAX-ACCESS read-write STATUS current DESCRIPTION "This time interval is used to count the time and logout web interface automatically." DEFVAL { 5 } ::= { companySystem 4 } sysLocationName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string." ::= { companySystem 5 } sysSystemPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set System Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark." ::= { companySystem 7 } sysSafeGuardEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set Safeguard Enable\Disable." DEFVAL { enable } ::= { companySystem 8 } sysRestart OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switch to be restarted. When the switch operationally goes down, configuration save operation is initiated based on the configuration save option chosen. When the switch operationally come up, the saved configurations are restored based on the restore option chosen. Once the switch is restarted, the value of this object reverts to 'false'." DEFVAL { false } ::= { companySystem 9 } sysSave OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to save Configuration." DEFVAL { false } ::= { companySystem 10 } sysJumboFrameEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Gigabit Web Smart Switches support jumbo frames (frames larger than the Ethernet frame size of 1522 bytes) of up to 9K bytes (tagged). Default jumbo frame is disabled." DEFVAL { disable } ::= { companySystem 12 } -- Port Control Table sysPortCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF SysPortCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control the port specific parameters of the device like speed, duplex mode, etc." ::= { companySystem 13 } sysPortCtrlEntry OBJECT-TYPE SYNTAX SysPortCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system. Index to the table is the interface index of the port." INDEX { sysPortCtrlIndex } ::= { sysPortCtrlTable 1 } SysPortCtrlEntry ::= SEQUENCE { sysPortCtrlIndex Integer32, sysPortCtrlSpeed INTEGER, sysPortCtrlOperStatus INTEGER, sysPortCtrlMDI INTEGER, sysPortCtrlFlowControl INTEGER, sysPortCtrlFlowControlOper INTEGER, sysPortCtrlType INTEGER , sysPortAutoDowngrade INTEGER } sysPortCtrlIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface index of the port for the configuration in this entry applies." ::= { sysPortCtrlEntry 1 } sysPortCtrlSpeed OBJECT-TYPE SYNTAX INTEGER { rate1000MFull (1), rate100MFull (2), rate100MHalf (3), rate10MFull (4), rate10MHalf (5), auto (6), disable (7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures interface speed." ::= { sysPortCtrlEntry 2 } sysPortCtrlOperStatus OBJECT-TYPE SYNTAX INTEGER { down (1), rate1000MFull (2), rate100MFull (3), rate100MHalf (4), rate10MFull (5), rate10MHalf (6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port's operating speed state." ::= { sysPortCtrlEntry 3 } sysPortCtrlMDI OBJECT-TYPE SYNTAX INTEGER { auto (1), mdi (2), mdix (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures interface auto/mdi/mdix mode. The default setting is Auto." ::= { sysPortCtrlEntry 4 } sysPortCtrlFlowControl OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables / disables flow control for the interface." ::= { sysPortCtrlEntry 5 } sysPortCtrlFlowControlOper OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The link parner negotiate port's operating flow control state." ::= { sysPortCtrlEntry 6 } sysPortCtrlType OBJECT-TYPE SYNTAX INTEGER { fastethernet(1), gigabitethernet(2), fiberwith100BaseSFPModule(3), fiberwith1000BaseSFPModule(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port's media type." ::= { sysPortCtrlEntry 7 } sysPortAutoDowngrade OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The port's media AutoDowngrade." ::= { sysPortCtrlEntry 10 } sysDhcpAutoConfiguration OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates auto config is enabled or disabled." DEFVAL { disable } ::= { companySystem 14 } -- start Port Description sysPortDescriptionTable OBJECT-TYPE SYNTAX SEQUENCE OF SysPortDescriptionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port description table." ::= { companySystem 16 } sysPortDescriptionEntry OBJECT-TYPE SYNTAX SysPortDescriptionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port description entry." INDEX { sysPortDescIndex} ::= { sysPortDescriptionTable 1 } SysPortDescriptionEntry ::= SEQUENCE { sysPortDescIndex INTEGER, sysPortDescString DisplayString } sysPortDescIndex OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the port index." ::= { sysPortDescriptionEntry 1 } sysPortDescString OBJECT-TYPE SYNTAX DisplayString(SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the port description." ::= { sysPortDescriptionEntry 2 } -- end Port Description sysDdp OBJECT IDENTIFIER ::= { companySystem 30 } sysDdpGlobalOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates D-Link discover protocol is enabled or disabled." ::= { sysDdp 1 } sysDdpGeneralReportOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates D-Link discover protocol report is enabled or disabled. This object only can be modified when D-Link discover protocol state is enabled." ::= { sysDdp 2 } sysDdpGeneralReportTimer OBJECT-TYPE SYNTAX INTEGER { time30seconds(30), time60seconds(60), time90seconds(90), time120seconds(120) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates D-Link discover protocol report time period. This object only can be modified when both D-Link discover protocol state and D-Link discover protocol report state are enabled." ::= { sysDdp 3 } sysDdpProtStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF SysDdpProtStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control the port status of D-Link discover protocol." ::= { sysDdp 4 } sysDdpProtStatusEntry OBJECT-TYPE SYNTAX SysDdpProtStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each port D-Link discover protocol status." INDEX { sysDdpProtStatusIndex } ::= { sysDdpProtStatusTable 1 } SysDdpProtStatusEntry ::= SEQUENCE { sysDdpProtStatusIndex Integer32, sysDdpProtStatusControl INTEGER } sysDdpProtStatusIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface index of the port for the configuration in this entry applies." ::= { sysDdpProtStatusEntry 1 } sysDdpProtStatusControl OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the port status of D-Link discover protocol." ::= { sysDdpProtStatusEntry 2 } sysDhcpRetryTimes OBJECT-TYPE SYNTAX Integer32 (5..120) MAX-ACCESS read-write STATUS current DESCRIPTION "This time for DHCP retried times." DEFVAL { 7 } ::= { companySystem 31 } -- ---------------------------------------------------------- -- The company802Dot3az Groups -- ---------------------------------------------------------- dot3azEEEset OBJECT IDENTIFIER ::= { companydot3azEEE 1 } -- 802Dot3azTable Group --------------------------------------------- -- dot3azTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3azEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control IEEE802.3az EEE settings features of the device." ::= { dot3azEEEset 1 } dot3azEntry OBJECT-TYPE SYNTAX Dot3azEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in IEEE802.3az EEE table for each interface in the system." INDEX { portD3Index } ::= { dot3azTable 1 } Dot3azEntry ::= SEQUENCE { portD3Index Integer32, portD3State INTEGER } portD3Index OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index for which the configuration in this entry applies." ::= { dot3azEntry 1 } portD3State OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2), notsupported (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable / disable port IEEE802.3az EEE admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled." ::= { dot3azEntry 2 } -- ------------------------------------------------------------------------- -- companyIpifGroup -- ------------------------------------------------------------------------- dhcpOption12Status OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Status of DHCP Option12" ::= { companyIpifGroup 6 } dhcpOption12HostName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Host name in DHCP option 12. The acceptable beginning of DHCP hostname is letter." ::= { companyIpifGroup 7 } -- ---------------------------------------------------------------- -- The multiIFSupportV4V6Info group -- ---------------------------------------------------------------- ipifSupportV4V6Info OBJECT IDENTIFIER ::= { companyIpifGroup 5 } sysIpAddrCfgMode OBJECT-TYPE SYNTAX INTEGER { manual(1), dhcp(2), bootp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system." DEFVAL { manual } ::= { ipifSupportV4V6Info 1 } sysIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored." ::= { ipifSupportV4V6Info 2 } sysIpSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored." ::= { ipifSupportV4V6Info 3 } sysGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Gateway" ::= { ipifSupportV4V6Info 4 } ipifName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Description for the interface." ::= { ipifSupportV4V6Info 5 } ipifv6GlobalStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The ID of VLAN that you want this interface to be in. It must be a exist vlan id." ::= { ipifSupportV4V6Info 7 } ipifv6DHCPStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of DHCPv6 that you want this interface to be in. It must be a exist vlan id." ::= { ipifSupportV4V6Info 8 } ipifv6AutolinkloStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The global state of link local that you want this interface to be in. It must be a exist vlan id." ::= { ipifSupportV4V6Info 9 } ipifv6NSRetransmitTime OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-create STATUS current DESCRIPTION "The NS's retransmit time that you want this interface to be in. It must be a exist vlan id." ::= { ipifSupportV4V6Info 10 } ipifv6DefaultGateway OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-create STATUS current DESCRIPTION "The ipv6 default gateway that you want this interface to be in. To delete gateway, please insert address '0000:0000:0000:0000:0000:0000:0000:0000'." ::= { ipifSupportV4V6Info 11 } -- --------------------------------------------------------------------- -- --------------------------------------------------------------------- ipifV6AddressTable OBJECT-TYPE SYNTAX SEQUENCE OF IpifV6AddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of interface entries." ::= { ipifSupportV4V6Info 12} ipifV6AddressEntry OBJECT-TYPE SYNTAX IpifV6AddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing management information applicable to a particular interface." INDEX { ipifV6AddressMainIndex, ipifV6AddressIpAddr, ipifV6AddressIpPrefix } ::= { ipifV6AddressTable 1 } IpifV6AddressEntry ::= SEQUENCE { ipifV6AddressMainIndex InterfaceIndex, ipifV6AddressIpAddr Ipv6Address, -- IPv6 Address. ipifV6AddressIpPrefix INTEGER, -- IPv6 Address Prefix. ipifV6AddressIpType INTEGER, -- IP type (Link-local, Global, anycast). ipifV6AddressRowStatus RowStatus -- IPv6 Address entries row status. } ipifV6AddressMainIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of this IPv6 entry." ::= { ipifV6AddressEntry 1 } ipifV6AddressIpAddr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The ip address of this IPv6 entry." DEFVAL { '00000000'H } ::= { ipifV6AddressEntry 2 } ipifV6AddressIpPrefix OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The ip prefix of this IPv6 entry." ::= { ipifV6AddressEntry 3 } ipifV6AddressIpType OBJECT-TYPE SYNTAX INTEGER { unicast(1), anycast(2), linklocal(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The ip type of this IPv6 entry." ::= { ipifV6AddressEntry 4 } ipifV6AddressRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of an entry in the Multi Interface Table. Only a subset of the rowstatus variables (active, createAndWait, destroy) are available." ::= { ipifV6AddressEntry 5 } -- ------------------------------------------------------------------------- -- companyTftpGroup -- ------------------------------------------------------------------------- tftpFwTargetGroup OBJECT IDENTIFIER ::= { companyTftpGroup 9 } tftpFwTargetServerIpAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The TFTP server's IP address is used to upload or download firmware." ::= { tftpFwTargetGroup 1 } tftpFwTargetServerIpType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of IP interface." ::= { tftpFwTargetGroup 2 } tftpFwTargetInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the interface name when the tftpFwTargetServerIpAddress is linklocal address." ::= { tftpFwTargetGroup 3 } tftpFwTargetImageFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Configure firmware filename to download." ::= { tftpFwTargetGroup 4 } tftpFwTargetTftpOperation OBJECT-TYPE SYNTAX INTEGER { none(0), download(1), upload(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName." ::= { tftpFwTargetGroup 5 } tftpFwTargetTftpOperationStatus OBJECT-TYPE SYNTAX INTEGER { none(0), success(1), fail(2), progressing(3), transmit(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The tftp operation status represent firmware backup or upgrade status." ::= { tftpFwTargetGroup 6 } tftpCfgTargetGroup OBJECT IDENTIFIER ::= { companyTftpGroup 10 } tftpCfgTargetServerIpAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The TFTP server's IP address is used to upload or download configuration file." ::= { tftpCfgTargetGroup 1 } tftpCfgTargetServerIpType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of IP interface." ::= { tftpCfgTargetGroup 2 } tftpCfgTargetInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the interface name when the tftpCfgTargetServerIpAddress is linklocal address." ::= { tftpCfgTargetGroup 3 } tftpCfgTargetImageFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "The configuration filename is used to store or retrieve config from the tftp server." ::= { tftpCfgTargetGroup 4 } tftpCfgTargetTftpOperation OBJECT-TYPE SYNTAX INTEGER { none(0), download(1), upload(2), progressing(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName." ::= { tftpCfgTargetGroup 5 } tftpCfgTargetTftpOperationStatus OBJECT-TYPE SYNTAX INTEGER { none(0), success(1), fail(2), progressing(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The tftp operation status represent configuration file backup or restore status." ::= { tftpCfgTargetGroup 6 } -- ------------------------------------------------------------------------- -- company Extension MIB, Miscellaneous Information -- ------------------------------------------------------------------------- miscReset OBJECT-TYPE SYNTAX INTEGER { reset(1), noop(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing." ::= { companyMiscGroup 2 } miscStatisticsReset OBJECT-TYPE SYNTAX INTEGER { reset(1), noop(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Resets the units statistics. A (1) resets the statistics count, a (2) does nothing." ::= { companyMiscGroup 3 } -- ---------------------------------------------------------- -- The companySecurity Groups -- ---------------------------------------------------------- securityIpMacPortBinding OBJECT IDENTIFIER ::= { companySecurity 10 } -- IpMacPortBinding Group --------------------------------------------- -- impbSettingTable OBJECT-TYPE SYNTAX SEQUENCE OF ImpbSettingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control IP-MAC-Port Binding Setting features of the device." ::= { securityIpMacPortBinding 1 } impbSettingEntry OBJECT-TYPE SYNTAX ImpbSettingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in IP-MAC-Port Binding Setting table for each interface in the system." INDEX { impbPortIndex } ::= { impbSettingTable 1 } ImpbSettingEntry ::= SEQUENCE { impbPortIndex INTEGER, impbPortState INTEGER, impbInsIpPacPortState INTEGER, impbDHCPPortState INTEGER } impbPortIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports." ::= { impbSettingEntry 1 } impbPortState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Disable / enable IP-MAC-Port Binding admin state for the interface." ::= { impbSettingEntry 2 } impbInsIpPacPortState OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable / disable IP-MAC-Port Binding also inspect IP packets state for the interface." ::= { impbSettingEntry 3 } impbDHCPPortState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Disable / enable IP-MAC-Port Binding DHCP snooping state for the interface." ::= { impbSettingEntry 4 } impbSmartTable OBJECT-TYPE SYNTAX SEQUENCE OF ImpbSmartEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control Smart IP-MAC-Port Binding features of the device." ::= { securityIpMacPortBinding 2 } impbSmartEntry OBJECT-TYPE SYNTAX ImpbSmartEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in Smart IP-MAC-Port Binding table for each interface in the system." INDEX { impbSmartMacAddress, impbSmartPort, impbSmartIpAddress} ::= { impbSmartTable 1 } ImpbSmartEntry ::= SEQUENCE { impbSmartMacAddress MacAddress, impbSmartPort Integer32, impbSmartIpAddress DisplayString, impbSmartVlanId Integer32, impbSmartBinding INTEGER } impbSmartMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the smart IP-MAC-PORT Binding entry." ::= { impbSmartEntry 1 } impbSmartPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the smart IP-MAC-PORT Binding entry." ::= { impbSmartEntry 2 } impbSmartIpAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address associated of the smart IP-MAC-PORT Binding entry." DEFVAL { '00000000'H } ::= { impbSmartEntry 3 } impbSmartVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the smart IP-MAC-PORT Binding entry." ::= { impbSmartEntry 4 } impbSmartBinding OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Disable / enable IP-MAC-Port Binding for the interface." ::= { impbSmartEntry 5 } impbWhiteListTable OBJECT-TYPE SYNTAX SEQUENCE OF ImpbWhiteListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control Manual IP-MAC-Port Binding white list features of the device." ::= { securityIpMacPortBinding 3 } impbWhiteListEntry OBJECT-TYPE SYNTAX ImpbWhiteListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in Manual IP-MAC-Port Binding white list table for each interface in the system." INDEX { impbWhiteListIpAddress, impbWhiteListMacAddress } ::= { impbWhiteListTable 1 } ImpbWhiteListEntry ::= SEQUENCE { impbWhiteListIpAddress DisplayString, impbWhiteListMacAddress MacAddress, impbWhiteListPort Integer32, impbWhiteListRowStatus RowStatus } impbWhiteListIpAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address associated of the Manual IP-MAC-PORT Binding white list entry." DEFVAL { '00000000'H } ::= { impbWhiteListEntry 1 } impbWhiteListMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the Manual IP-MAC-PORT Binding white list entry." ::= { impbWhiteListEntry 2 } impbWhiteListPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The port number of the Manual IP-MAC-PORT Binding white list entry." ::= { impbWhiteListEntry 3 } impbWhiteListRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of a row in impbWhiteListTable. By setting this object, new entries can be created in impbWhiteListTable and existing entries can be removed from impbWhiteListTable. It can be used as specified in the SNMP v2 standard." ::= { impbWhiteListEntry 4 } impbBlackListTable OBJECT-TYPE SYNTAX SEQUENCE OF ImpbBlackListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control IP-MAC-Port Binding black list of the device." ::= { securityIpMacPortBinding 4 } impbBlackListEntry OBJECT-TYPE SYNTAX ImpbBlackListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in Manual IP-MAC-Port Binding black list table for each interface in the system." INDEX { impbBlackListMacAddress, impbBlackListVlanId, impbBlackListPort } ::= { impbBlackListTable 1 } ImpbBlackListEntry ::= SEQUENCE { impbBlackListMacAddress MacAddress, impbBlackListVlanId Integer32, impbBlackListPort Integer32, impbBlackListIpAddress DisplayString, impbBlackListStatus INTEGER } impbBlackListMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the IP-MAC-PORT Binding black list entry." ::= { impbBlackListEntry 1 } impbBlackListVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the IP-MAC-PORT Binding black list entry." ::= { impbBlackListEntry 2 } impbBlackListPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the IP-MAC-PORT Binding black list entry." ::= { impbBlackListEntry 3 } impbBlackListIpAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address associated of the IP-MAC-PORT Binding black list entry." ::= { impbBlackListEntry 4 } impbBlackListStatus OBJECT-TYPE SYNTAX INTEGER { nothing (0), deleted (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "nothing/delete IP-MAC-Port Binding for the interface." ::= { impbBlackListEntry 5 } impbAutoScanIpAddressFrom OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The begin for IP address associated of the IP-MAC-PORT Binding auto scan entry." DEFVAL { '00000000'H } ::= { securityIpMacPortBinding 5 } impbAutoScanIpAddressTo OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The end for IP address associated of the IP-MAC-PORT Binding auto scan entry." DEFVAL { '00000000'H } ::= { securityIpMacPortBinding 6 } impbAutoScanStatus OBJECT-TYPE SYNTAX INTEGER { nothing (0), scan (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Nothing / scan IP-MAC-Port Binding auto scan for the interface." ::= { securityIpMacPortBinding 7 } -- ---------------------------------------------------------------- -- The RSTP group -- ---------------------------------------------------------------- stpGlobal OBJECT IDENTIFIER ::= { companyRSTP 1 } rstpStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative module status requested by management for the RSTP Module. This enables or disables RSTP in the system. A value of 'enabled' (1) indicates that RSTP must be enabled in the device on all the ports. A value of 'disabled'(2) indicates that RSTP must be disabled in the device on all the ports." ::= {stpGlobal 1 } stpVersion OBJECT-TYPE SYNTAX INTEGER { stpCompatible(0), rstp(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning Tree Protocol specified in IEEE 802.1w. New value may be defined as future versions of the protocol become available." REFERENCE "IEEE 802.1D-2004" DEFVAL { rstp } ::= { stpGlobal 2 } stpPriority OBJECT-TYPE SYNTAX INTEGER (0..61440) MAX-ACCESS read-write STATUS current DESCRIPTION "The bridge priority vector, as defined in 17.6. The first (RootBridgeID) and third (DesignatedBridgeID)components are both equal to the value of the Bridge Identifier (17.18.2). The other components are zero. Permissible values are 0-61440, in steps of 4096." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 3 } stpTxHoldCount OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The value used by the Port Transmit state machine to limit the maximum transmission rate." REFERENCE "IEEE 802.1D-2004" DEFVAL { 6 } ::= { stpGlobal 4 } stpProtocolSpecification OBJECT-TYPE SYNTAX INTEGER { unknown(1), decLb100(2), ieee8021d(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined." ::= { stpGlobal 5 } stpTimeSinceTopologyChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 6 } stpTopChanges OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of topology changes detected by this bridge since the management entity was last reset or initialized." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 7 } stpDesignatedRoot OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 8 } stpRootCost OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of the path to the root as seen from this bridge." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 9 } stpRootPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the port which offers the lowest cost path from this bridge to the root bridge." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 10 } stpMaxAge OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. The rootTimes variable comprises the Bridge¡¦s operational timer parameter values (Message Age, Max Age, Forward Delay, and Hello Time), derived from the values stored in portTimes (17.19.22) for the Root Port or from BridgeTimes (17.18.4)." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 11 } stpHelloTime OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. The interval between periodic transmissions of Configuration Messages by Designated Ports (Table 17-1)." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 12 } stpHoldTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 13 } stpForwardDelay OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. The delay used by STP Bridges (17.4) to transition Root and Designated Ports to Forwarding (Table 17-1)." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 14 } stpBridgeMaxAge OBJECT-TYPE SYNTAX Timeout (600..4000) MAX-ACCESS read-write STATUS current DESCRIPTION "The Max Age component of designatedTimes (17.19.5). This time value, measured in units of hundredths of a second. BridgeTimes comprises four components¡Xthe current values of Bridge Forward Delay, Bridge Hello Time, and Bridge Max Age (17.13, Table 17-1), and a Message Age of zero." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 15 } stpBridgeHelloTime OBJECT-TYPE SYNTAX Timeout (100..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "The Hello Time component of designatedTimes (17.19.5). This time value, measured in units of hundredths of a second. BridgeTimes comprises four components¡Xthe current values of Bridge Forward Delay, Bridge Hello Time, and Bridge Max Age (17.13, Table 17-1), and a Message Age of zero." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 16 } stpBridgeForwardDelay OBJECT-TYPE SYNTAX Timeout (400..3000) MAX-ACCESS read-write STATUS current DESCRIPTION "The Forward Delay component of designatedTimes (17.19.5). This time value, measured in units of hundredths of a second. BridgeTimes comprises four components¡Xthe current values of Bridge Forward Delay, Bridge Hello Time, and Bridge Max Age (17.13, Table 17-1), and a Message Age of zero." REFERENCE "IEEE 802.1D-2004" ::= { stpGlobal 17 } -- ------------------------------------- -- The Spanning Tree Port Table -- ------------------------------------- stpPortTable OBJECT-TYPE SYNTAX SEQUENCE OF StpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains port-specific information for the Spanning Tree Protocol." ::= { companyRSTP 2 } stpPortEntry OBJECT-TYPE SYNTAX StpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information maintained by every port about the Spanning Tree Protocol state for that port." INDEX { stpPort } ::= { stpPortTable 1 } StpPortEntry ::= SEQUENCE { stpPort INTEGER, stpPortPriority INTEGER, stpPortState INTEGER, stpPortEnable INTEGER, stpAdminPortPathCost INTEGER, stpPortPathCost INTEGER, stpPortDesignatedRoot BridgeId, stpPortDesignatedCost INTEGER, stpPortDesignatedBridge BridgeId, stpPortDesignatedPort OCTET STRING, stpPortForwardTransitions Counter32, stpPortProtocolMigration TruthValue, stpPortOperEdgePort TruthValue, stpPortAdminPointToPoint INTEGER, stpPortOperPointToPoint TruthValue, stpPortEdge INTEGER, stpPortRestrictedRole TruthValue, stpPortRestrictedTCN TruthValue } stpPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the port for which this entry contains Spanning Tree Protocol management information." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 1 } stpPortPriority OBJECT-TYPE SYNTAX INTEGER (0..240) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of stpPort." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 2 } stpPortState OBJECT-TYPE SYNTAX INTEGER { disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see stpPortEnable), this object will have a value of disabled(1)." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 3 } stpPortEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The enabled/disabled status of the port." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 4 } stpAdminPortPathCost OBJECT-TYPE SYNTAX INTEGER (0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automatically calculated default Path Cost value to the ohter object stpPortPathCost. If the default Path Cost is being used,this object returns '0' when read." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 5 } stpPortPathCost OBJECT-TYPE SYNTAX INTEGER (1..200000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the spanning tree root which include this port." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 6 } stpPortDesignatedRoot OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 7 } stpPortDesignatedCost OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 8 } stpPortDesignatedBridge OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 9 } stpPortDesignatedPort OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Port Identifier of the port on the Designated Bridge for this port's segment." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 10 } stpPortForwardTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this port has transitioned from the Learning state to the Forwarding state." ::= { stpPortEntry 11 } stpPortProtocolMigration OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "When operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns FALSE(2) when read." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 12 } stpPortOperEdgePort OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The operational value of the Edge Port parameter. The object is initialized to the value of stpPortAdminEdgePort and is set FALSE on reception of a BPDU." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 13 } stpPortAdminPointToPoint OBJECT-TYPE SYNTAX INTEGER { forceTrue(0), forceFalse(1), auto(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 14 } stpPortOperPointToPoint OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the stpPortAdminPointToPoint object." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 15 } stpPortEdge OBJECT-TYPE SYNTAX INTEGER { true(1), false(0), auto(2) } MAX-ACCESS read-write STATUS current DESCRIPTION " This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled." ::= { stpPortEntry 16 } stpPortRestrictedRole OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected. This parameter should be FALSE by default. If set it can cause lack of spanning tree connectivity. It is set by a network administrator to prevent bridges external to a core region of the network influencing the spanning tree active topology, possibly because those bridges are not under the full control of the administrator. This administrator configuration is also known as 'Root Guard'." ::= { stpPortEntry 17 } stpPortRestrictedTCN OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause temporary loss of connectivity after changes in a spanning trees active topology as a result of persistent incorrectly learnt station location information. It is set by a network administrator to prevent bridges external to a core region of the network causing address flushing in that region, possibly because those bridges are not under the full control of the administrator or MAC_Operational for the attached LANs transitions frequently." ::= { stpPortEntry 18 } -- ------------------------------------------------------------------ -- The Static Multicast Group -- ------------------------------------------------------------------ staticMcastTable OBJECT-TYPE SYNTAX SEQUENCE OF StaticMcastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the Static MACs" ::= { companyStaticMcast 1 } staticMcastEntry OBJECT-TYPE SYNTAX StaticMcastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Static MAC entry containing the mac and forwarding port." INDEX { staticMcastVlanID, staticMcastMac, staticMcastEgressPorts} ::= { staticMcastTable 1 } StaticMcastEntry ::= SEQUENCE { staticMcastVlanID INTEGER, staticMcastMac MacAddress, staticMcastEgressPorts PortList, staticMcastStatus RowStatus } staticMcastVlanID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the static MAC entry." ::= { staticMcastEntry 1 } staticMcastMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the static MAC entry." ::= { staticMcastEntry 2 } staticMcastEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of any dynamic information e.g. from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastForbiddenEgressPorts. The default value of this object is a string of ones of appropriate length." REFERENCE "IEEE 802.1Q/D11 Section 12.7.7.3, 11.2.3.2.3" ::= { staticMcastEntry 3 } staticMcastStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of an entry in the Static Mcast Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available." ::= { staticMcastEntry 4 } -- ---------------------------------------------------------- -- The 802.1Q VLAN Groups -- ---------------------------------------------------------- dot1qVlanManagementOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable management VLAN mechanism." ::= { companyDot1qVlanGroup 2 } dot1qVlanManagementid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The management VLAN ID, which will allow to forward packets of that VLAN to CPU." DEFVAL { 1 } ::= { companyDot1qVlanGroup 3 } dot1qVlanAsyOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable IEEE 802.1Q Asymmetric VLAN" ::= { companyDot1qVlanGroup 5 } -- ------------------------------------------------------------- -- The VLAN Database -- ------------------------------------------------------------- dot1qVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset." ::= { companyDot1qVlanGroup 6 } dot1qVlanEntry OBJECT-TYPE SYNTAX Dot1qVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information for a VLAN configured into the device by (local or network) management." INDEX { dot1qVlanName } ::= { dot1qVlanTable 1 } Dot1qVlanEntry ::= SEQUENCE { dot1qVlanName SnmpAdminString, dot1qVlanEgressPorts PortList, dot1qVlanUntaggedPorts PortList, dot1qVlanRowStatus RowStatus } dot1qVlanName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..20)) MAX-ACCESS read-create STATUS current DESCRIPTION "An administratively assigned string, which may be used to identify the VLAN." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanEntry 1 } dot1qVlanEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed." REFERENCE "IEEE 802.1Q/D11 Section 12.7.7.3, 11.2.3.2.3" ::= { dot1qVlanEntry 2 } dot1qVlanUntaggedPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set then it will reject the set operation with an error. An example might be if a manager attempts to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanEntry 4 } dot1qVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanTable. It can be used as specified in the SNMP v2 standard." ::= { dot1qVlanEntry 5 } -- ------------------------------------------------------------- -- The VLAN Port Configuration Table -- ------------------------------------------------------------- dot1qVlanPortTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qVlanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per port control and status information for VLAN configuration in the device." ::= { companyDot1qVlanGroup 7 } dot1qVlanPortEntry OBJECT-TYPE SYNTAX Dot1qVlanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling VLAN configuration for a port on the device." AUGMENTS { dot1dBasePortEntry } ::= { dot1qVlanPortTable 1 } Dot1qVlanPortEntry ::= SEQUENCE { dot1qVlanPvid VlanIndex } dot1qVlanPvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-write STATUS current DESCRIPTION "The PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this port." REFERENCE "IEEE 802.1Q/D11 Section 12.10.1.1" DEFVAL { 1 } ::= { dot1qVlanPortEntry 1 } -- ------------------------------------------------------------- -- The VLAN Ungister Multicast Filter Table -- ------------------------------------------------------------- dot1qVlanUngisterMCFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qVlanUngisterMCFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the list of ports through which a router, in a particular VLAN is reachable." ::= { companyDot1qVlanGroup 8 } dot1qVlanUngisterMCFilterEntry OBJECT-TYPE SYNTAX Dot1qVlanUngisterMCFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of multicast filter mode information for each VLAN ID." INDEX { dot1qVlanUngisterMCFilterVlanId } ::= { dot1qVlanUngisterMCFilterTable 1 } Dot1qVlanUngisterMCFilterEntry ::= SEQUENCE { dot1qVlanUngisterMCFilterVlanId Integer32, dot1qVlanUngisterMCFiltermode INTEGER } dot1qVlanUngisterMCFilterVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "Per Vlan to configure multicast filtering function." ::= { dot1qVlanUngisterMCFilterEntry 1 } dot1qVlanUngisterMCFiltermode OBJECT-TYPE SYNTAX INTEGER { filter(1), forward(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Filter unknown multicast frames or normal operation(i.e. forwarding)" ::= { dot1qVlanUngisterMCFilterEntry 2 } -- --------------------------------------------------------------------- -- LA Function -- --------------------------------------------------------------------- laSystem OBJECT IDENTIFIER ::= { companyLA 1 } laPortControl OBJECT IDENTIFIER ::= { companyLA 2 } -- ------------------------------------------------------------- -- Textual Conventions -- ------------------------------------------------------------- PortLaMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Defines how a Port Channel does channeling. lacp(1) - place the port into passive negotiation state, in which the port waits for its peer to initiate negotiation. static(2) - force the port to enable channeling. disable(3) - channeling is disabled." SYNTAX INTEGER { lacp(1), static(2), disable(3) } LacpKey ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The Actor or Partner Key value (0..65535)." SYNTAX Integer32 (0..65535) -- ------------------------------------------------------------------ -- The La System Group -- ------------------------------------------------------------------ laStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the Link Aggregation Module administrative status as enabled or disabled." ::= { laSystem 2 } -- -- Port Channel Table -- laPortChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF LaPortChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel." ::= { laSystem 3 } laPortChannelEntry OBJECT-TYPE SYNTAX LaPortChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each created port-channel port." INDEX { laPortChannelIfIndex } ::= { laPortChannelTable 1 } LaPortChannelEntry ::= SEQUENCE { laPortChannelIfIndex InterfaceIndex, laPortChannelMemberList PortList, laPortChannelMode PortLaMode } laPortChannelIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port-channel(Aggregator's interface index). " ::= { laPortChannelEntry 1 } laPortChannelMemberList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Member Port list of the port channel. Add the ports as a aggregation member associated of a port-channel." ::= { laPortChannelEntry 2 } laPortChannelMode OBJECT-TYPE SYNTAX PortLaMode MAX-ACCESS read-write STATUS current DESCRIPTION "Current Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (Manual). disable(3) - channeling is disabled." ::= { laPortChannelEntry 3 } -- -- LA Port Control Table -- laPortControlTable OBJECT-TYPE SYNTAX SEQUENCE OF LaPortControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains Link Aggregation Control configuration information about every Aggregation Port associated with this device. A row appears in this table for each physical port." ::= { laPortControl 1 } laPortControlEntry OBJECT-TYPE SYNTAX LaPortControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Link Aggregation Control configuration parameters for each Aggregation Port on this device." INDEX { laPortControlIndex } ::= { laPortControlTable 1 } LaPortControlEntry ::= SEQUENCE { laPortControlIndex InterfaceIndex, laPortActorActivity INTEGER, laPortActorTimeout INTEGER } laPortControlIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port." ::= { laPortControlEntry 1 } laPortActorActivity OBJECT-TYPE SYNTAX INTEGER { active(1), passive(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates LACP_Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send frames along the configured links. If the actor and partner are both in passive mode, they do not exchange LACP packets." ::= { laPortControlEntry 3 } laPortActorTimeout OBJECT-TYPE SYNTAX INTEGER { short(1), long(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates LACP_Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds." ::= { laPortControlEntry 4 } -- ---------------------------------------------------------------- -- The STATIC MAC group -- ---------------------------------------------------------------- staticDisableAutoLearn OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set on to disable Auto Learning Excluding Uplink Port and set off to enable Auto Learning." ::= { companyStaticMAC 1 } staticAutoLearningList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The set of the device's member ports that belong to the Static MAC auto learning enable/disable. For example, when Disable Auto Learning is enable, the octet value set up as '# 0x0F 0xFF 0xFF 0xFF' means from port 1 to port 4 are not in auto learning state, the other ports are in auto learning state. It can be set up when Disable Auto Learning is enable." ::= { companyStaticMAC 2 } staticTable OBJECT-TYPE SYNTAX SEQUENCE OF StaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the Static MACs" ::= { companyStaticMAC 3 } staticEntry OBJECT-TYPE SYNTAX StaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Static MAC entry containing the mac and forwarding port." INDEX { staticVlanID, staticMac,staticPort} ::= { staticTable 1 } StaticEntry ::= SEQUENCE { staticVlanID INTEGER, staticMac MacAddress, staticPort INTEGER, staticStatus RowStatus } staticVlanID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the static MAC entry." ::= { staticEntry 1 } staticMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the static MAC entry." ::= { staticEntry 2 } staticPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The forwarding port of the static MAC entry." ::= { staticEntry 3 } staticStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static MAC." ::= { staticEntry 4 } -- --------------------------------------------------------------------- -- IGMP Snooping Function -- --------------------------------------------------------------------- igsSystem OBJECT IDENTIFIER ::= { companyIgsGroup 1 } igsVlan OBJECT IDENTIFIER ::= { companyIgsGroup 3 } igsStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops performing protocol operations." DEFVAL { 2 } ::= { igsSystem 1 } igsRouterPortPurgeInterval OBJECT-TYPE SYNTAX Integer32 (60..600) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted." DEFVAL { 260 } ::= { igsSystem 2 } igsHostPortPurgeInterval OBJECT-TYPE SYNTAX Integer32 (130..153025) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group." DEFVAL {260} ::= { igsSystem 3 } igsRobustnessValue OBJECT-TYPE SYNTAX Integer32 (2..255) MAX-ACCESS read-write STATUS current DESCRIPTION "When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'igsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group." DEFVAL { 2 } ::= { igsSystem 4 } igsGrpQueryInterval OBJECT-TYPE SYNTAX Integer32 (1..25) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'igsRobustnessValue' queries before removing the port from the group membership information in the forwarding database." DEFVAL { 1 } ::= { igsSystem 5 } igsQueryInterval OBJECT-TYPE SYNTAX Integer32 (60..600) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs." DEFVAL { 125 } ::= { igsSystem 6 } igsQueryMaxResponseTime OBJECT-TYPE SYNTAX INTEGER (10..25) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum query response time advertised in IGMPv2 general queries on this interface." DEFVAL { 10 } ::= { igsSystem 7 } igsReportToAllPort OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module forwards packets to report to all port. When set to 'disabled', the IGS module forwards packets to router port only." DEFVAL { 2 } ::= { igsSystem 8 } -- VLAN Based MAC Multicast Forwarding Table -- -- igsVlanMcastMacFwdTable OBJECT-TYPE -- SYNTAX SEQUENCE OF IgsVlanMcastMacFwdEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "This table contains MAC based multicast forwarding -- information. This information is applicable only if -- the 'igsVlanMcastForwardingMode' is set to 'macbased' " -- ::= { igsVlan 1 } -- -- igsVlanMcastMacFwdEntry OBJECT-TYPE -- SYNTAX IgsVlanMcastMacFwdEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "This table contains VLAN ID, multicast group MAC address and the -- list of ports onto which the multicast data packets for group -- should be forwarded." -- -- INDEX { igsVlanMcastMacFwdVlanId, -- igsVlanMcastMacFwdGroupAddress } -- ::= { igsVlanMcastMacFwdTable 1 } -- -- IgsVlanMcastMacFwdEntry ::= SEQUENCE { -- igsVlanMcastMacFwdVlanId Integer32, -- igsVlanMcastMacFwdGroupAddress MacAddress, -- igsVlanMcastMacFwdPortList PortList -- } -- -- igsVlanMcastMacFwdVlanId OBJECT-TYPE -- SYNTAX Integer32 (1..4094) -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "VLAN ID pertaining to the Multicast forwarding entry" -- ::= { igsVlanMcastMacFwdEntry 1 } -- -- igsVlanMcastMacFwdGroupAddress OBJECT-TYPE -- SYNTAX MacAddress -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "Multicast group MAC address." -- ::= { igsVlanMcastMacFwdEntry 2 } -- -- -- igsVlanMcastMacFwdPortList OBJECT-TYPE -- SYNTAX PortList -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "List of ports onto which the multicast data -- packets destined for this group will be forwarded." -- ::= { igsVlanMcastMacFwdEntry 3 } -- VLAN based router table. igsVlanRouterTable OBJECT-TYPE SYNTAX SEQUENCE OF IgsVlanRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the list of ports through which a router, in a particular VLAN is reachable." ::= { igsVlan 3 } igsVlanRouterEntry OBJECT-TYPE SYNTAX IgsVlanRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An igs vlan router entry contain the igs vlan router port list." INDEX { igsVlanRouterVlanId } ::= { igsVlanRouterTable 1 } IgsVlanRouterEntry ::= SEQUENCE { igsVlanRouterVlanId Integer32, igsVlanRouterPortList PortList } igsVlanRouterVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "It is the VLAN ID of the igs vlan router entry." ::= { igsVlanRouterEntry 1 } igsVlanRouterPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically." ::= { igsVlanRouterEntry 2 } -- VLAN based filter table igsVlanFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF IgsVlanFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system." ::= { igsVlan 4 } igsVlanFilterEntry OBJECT-TYPE SYNTAX IgsVlanFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains snooping status , version and fast leave configuration for a specific VLAN." INDEX { igsVlanFilterVlanId } ::= { igsVlanFilterTable 1 } IgsVlanFilterEntry ::= SEQUENCE { igsVlanFilterVlanId Integer32, igsVlanSnoopStatus INTEGER, igsVlanQuerier INTEGER, igsVlanCfgQuerier INTEGER, igsVlanQueryInterval Integer32, igsVlanRtrPortList PortList, igsVlanFastLeave INTEGER } igsVlanFilterVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done." ::= { igsVlanFilterEntry 1 } igsVlanSnoopStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows you to enable/disable IGS function on a specific VLAN." DEFVAL { 1 } ::= { igsVlanFilterEntry 2 } igsVlanQuerier OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the switch is configured as a querier in the VLAN" DEFVAL { 2 } ::= { igsVlanFilterEntry 3 } igsVlanCfgQuerier OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries." DEFVAL { 2 } ::= { igsVlanFilterEntry 4 } igsVlanQueryInterval OBJECT-TYPE SYNTAX Integer32 (60..600) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network." DEFVAL { 125 } ::= { igsVlanFilterEntry 5 } igsVlanRtrPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "List of ports which are configured statically as router ports" ::= { igsVlanFilterEntry 6 } igsVlanFastLeave OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table." DEFVAL { 2 } ::= { igsVlanFilterEntry 8 } -- VLAN Based IGMP Snooping Group igsVlanMulticastGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF IgsVlanMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains MAC based multicast forwarding information." ::= { igsVlan 5 } igsVlanMulticastGroupEntry OBJECT-TYPE SYNTAX IgsVlanMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded." INDEX { igsVlanMulticastGroupVlanId, igsVlanMulticastGroupIpAddress } ::= { igsVlanMulticastGroupTable 1 } IgsVlanMulticastGroupEntry ::= SEQUENCE { igsVlanMulticastGroupVlanId Integer32, igsVlanMulticastGroupIpAddress InetAddress, igsVlanMulticastGroupMacAddress MacAddress, igsVlanMulticastGroupPortList PortList } igsVlanMulticastGroupVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID pertaining to the Multicast forwarding entry" ::= { igsVlanMulticastGroupEntry 1 } igsVlanMulticastGroupIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format." ::= { igsVlanMulticastGroupEntry 2 } igsVlanMulticastGroupMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format." ::= { igsVlanMulticastGroupEntry 3 } igsVlanMulticastGroupPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "List of ports onto which the multicast data packets destined for this group will be forwarded." ::= { igsVlanMulticastGroupEntry 4 } -- --------------------------------------------------------------------- -- MLD Snooping Function -- --------------------------------------------------------------------- mldsSystem OBJECT IDENTIFIER ::= { companyMldsGroup 1 } mldsVlan OBJECT IDENTIFIER ::= { companyMldsGroup 3 } mldsStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables MLD snooping in the system. When set to 'enabled', the MLDS module starts protocol operations. When set to 'disabled', the MLDS module stops performing protocol operations." DEFVAL { 2 } ::= { mldsSystem 1 } mldsRouterPortPurgeInterval OBJECT-TYPE SYNTAX Integer32 (60..600) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted." DEFVAL { 260 } ::= { mldsSystem 2 } mldsHostPortPurgeInterval OBJECT-TYPE SYNTAX Integer32 (130..153025) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group." DEFVAL {260} ::= { mldsSystem 3 } mldsRobustnessValue OBJECT-TYPE SYNTAX Integer32 (2..255) MAX-ACCESS read-write STATUS current DESCRIPTION "When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'mldsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group." DEFVAL { 2 } ::= { mldsSystem 4 } mldsGrpQueryInterval OBJECT-TYPE SYNTAX Integer32 (1..25) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'mldsRobustnessValue' queries before removing the port from the group membership information in the forwarding database." DEFVAL { 1 } ::= { mldsSystem 5 } mldsQueryInterval OBJECT-TYPE SYNTAX Integer32 (60..600) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs." DEFVAL { 125 } ::= { mldsSystem 6 } mldsQueryMaxResponseTime OBJECT-TYPE SYNTAX INTEGER (10..25) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum query response time advertised in MLDv1 general queries on this interface." DEFVAL { 10 } ::= { mldsSystem 7 } -- VLAN based router table. mldsVlanRouterTable OBJECT-TYPE SYNTAX SEQUENCE OF MldsVlanRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the list of ports through which a router, in a particular VLAN is reachable." ::= { mldsVlan 3 } mldsVlanRouterEntry OBJECT-TYPE SYNTAX MldsVlanRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the VLAN ID and list of ports on which routers are present in the VLAN." INDEX { mldsVlanRouterVlanId } ::= { mldsVlanRouterTable 1 } MldsVlanRouterEntry ::= SEQUENCE { mldsVlanRouterVlanId Integer32, mldsVlanRouterPortList PortList } mldsVlanRouterVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID of the ports through which router is reachable." ::= { mldsVlanRouterEntry 1 } mldsVlanRouterPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically." ::= { mldsVlanRouterEntry 2 } -- VLAN based filter table mldsVlanFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF MldsVlanFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system." ::= { mldsVlan 4 } mldsVlanFilterEntry OBJECT-TYPE SYNTAX MldsVlanFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains snooping status , version and fast leave configuration for a specific VLAN." INDEX { mldsVlanFilterVlanId } ::= { mldsVlanFilterTable 1 } MldsVlanFilterEntry ::= SEQUENCE { mldsVlanFilterVlanId Integer32, mldsVlanSnoopStatus INTEGER, mldsVlanQuerier INTEGER, mldsVlanCfgQuerier INTEGER, mldsVlanQueryInterval Integer32, mldsVlanRtrPortList PortList , mldsVlanFastLeave INTEGER } mldsVlanFilterVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "Index of MldsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in MldsVlanFilterEntry is to be done." ::= { mldsVlanFilterEntry 1 } mldsVlanSnoopStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows you to enable/disable MLDS function on a specific VLAN." DEFVAL { 1 } ::= { mldsVlanFilterEntry 2 } mldsVlanQuerier OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the switch is configured as a querier in the VLAN" DEFVAL { 2 } ::= { mldsVlanFilterEntry 3 } mldsVlanCfgQuerier OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The snooping switch can be configured as a querier via this object to send out MLD general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries." DEFVAL { 2 } ::= { mldsVlanFilterEntry 4 } mldsVlanQueryInterval OBJECT-TYPE SYNTAX Integer32 (60..600) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network." DEFVAL { 125 } ::= { mldsVlanFilterEntry 5 } mldsVlanRtrPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "List of ports which are configured statically as router ports" ::= { mldsVlanFilterEntry 6 } mldsVlanFastLeave OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table." DEFVAL { 2 } ::= { mldsVlanFilterEntry 8 } -- VLAN Based MLD Snooping Group mldsVlanMulticastGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MldsVlanMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains MAC based multicast forwarding information." ::= { mldsVlan 5 } mldsVlanMulticastGroupEntry OBJECT-TYPE SYNTAX MldsVlanMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded." INDEX { mldsVlanMulticastGroupVlanId, mldsVlanMulticastGroupIpAddress } ::= { mldsVlanMulticastGroupTable 1 } MldsVlanMulticastGroupEntry ::= SEQUENCE { mldsVlanMulticastGroupVlanId Integer32, mldsVlanMulticastGroupIpAddress InetAddress, mldsVlanMulticastGroupMacAddress MacAddress, mldsVlanMulticastGroupPortList PortList } mldsVlanMulticastGroupVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID pertaining to the Multicast forwarding entry" ::= { mldsVlanMulticastGroupEntry 1 } mldsVlanMulticastGroupIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format." ::= { mldsVlanMulticastGroupEntry 2 } mldsVlanMulticastGroupMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format." ::= { mldsVlanMulticastGroupEntry 3 } mldsVlanMulticastGroupPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "List of ports onto which the multicast data packets destined for this group will be forwarded." ::= { mldsVlanMulticastGroupEntry 4 } -- ------------------------------------------------------------- -- groups in the Auth MIB -- ------------------------------------------------------------- swAuthenCtrl OBJECT IDENTIFIER ::= { companyAuthGroup 1 } -- ----------------------------------------------------------------------------- -- swAuthenCtrl -- ----------------------------------------------------------------------------- swAuthStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Static 802.1x." ::= { swAuthenCtrl 1 } authProtocol OBJECT-TYPE SYNTAX INTEGER { authProtocolRadiusEap(1), authProtocolLocal(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The authentication method used to authenticate users." DEFVAL { authProtocolRadiusEap } ::= { swAuthenCtrl 3 } swAuthCtrlPktFwdMode OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable 802.1x packet forward while 802.1x module is disabled." ::= { swAuthenCtrl 4 } -- ------------------------------------------------------------- -- groups in the Port Access Control MIB -- ------------------------------------------------------------- swAuthPortAccessCtrl OBJECT IDENTIFIER ::= { companyAuthGroup 2 } -- ----------------------------------------------------------------------------- -- swAuthPortAccessCtrl -- ----------------------------------------------------------------------------- swAuthPortAccessControlTable OBJECT-TYPE SYNTAX SEQUENCE OF SwAuthPortAccessControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself." ::= { swAuthPortAccessCtrl 1 } swAuthPortAccessControlEntry OBJECT-TYPE SYNTAX SwAuthPortAccessControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration information for an Authenticator Port." INDEX { swAuthAuthConfigPortNumber } ::= { swAuthPortAccessControlTable 1 } SwAuthPortAccessControlEntry ::= SEQUENCE { swAuthAuthConfigPortNumber INTEGER, swAuthAuthQuietPeriod INTEGER, swAuthAuthSuppTimeout INTEGER, swAuthAuthServerTimeout INTEGER, swAuthAuthMaxReq INTEGER, swAuthAuthTxPeriod INTEGER, swAuthAuthReAuthPeriod INTEGER, swAuthAuthReAuthentication INTEGER, swAuthAuthConfigPortControl INTEGER, swAuthAuthCapability INTEGER, swAuthAuthDirection INTEGER } swAuthAuthConfigPortNumber OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number." ::= { swAuthPortAccessControlEntry 1 } swAuthAuthQuietPeriod OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine." REFERENCE "9.4.1, quietPeriod." DEFVAL { 60 } ::= { swAuthPortAccessControlEntry 2 } swAuthAuthSuppTimeout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine." REFERENCE "9.4.1, suppTimeout." DEFVAL { 12 } ::= { swAuthPortAccessControlEntry 3 } swAuthAuthServerTimeout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine." REFERENCE "9.4.1, serverTimeout." DEFVAL { 16 } ::= { swAuthPortAccessControlEntry 4 } swAuthAuthMaxReq OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of the maxReq constant currently in use by the Backend Authentication state machine." REFERENCE "9.4.1, maxReq." DEFVAL { 2 } ::= { swAuthPortAccessControlEntry 5 } swAuthAuthTxPeriod OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine." REFERENCE "9.4.1, txPeriod." DEFVAL { 24 } ::= { swAuthPortAccessControlEntry 6 } swAuthAuthReAuthPeriod OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine." REFERENCE "9.4.1, reAuthPerio." DEFVAL { 3600 } ::= { swAuthPortAccessControlEntry 7 } swAuthAuthReAuthentication OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1)." REFERENCE "9.4.1, reAuthEnable." ::= { swAuthPortAccessControlEntry 8 } swAuthAuthConfigPortControl OBJECT-TYPE SYNTAX INTEGER { forceUnauthorized(1), auto(2), forceAuthorized(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The current value of the controlled Port control parameter for the Port." REFERENCE "9.4.1, AuthControlledPortControl." ::= { swAuthPortAccessControlEntry 9 } swAuthAuthCapability OBJECT-TYPE SYNTAX INTEGER { authenticator(1), none(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The current value of the controlled Port control parameter for the Port." REFERENCE "AuthCapability." ::= { swAuthPortAccessControlEntry 10 } swAuthAuthDirection OBJECT-TYPE SYNTAX INTEGER { both(0), in(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The current value of the controlled Port control parameter for the Port." REFERENCE "AuthDirection." ::= { swAuthPortAccessControlEntry 11 } -- ------------------------------------------------------------- -- groups in the 802.1X Local user MIB -- ------------------------------------------------------------- swAuthUser OBJECT IDENTIFIER ::= { companyAuthGroup 3 } -- ----------------------------------------------------------------------------- -- swAuthUser -- ----------------------------------------------------------------------------- swAuthUserTable OBJECT-TYPE SYNTAX SEQUENCE OF SwAuthUserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself." ::= { swAuthUser 1 } swAuthUserEntry OBJECT-TYPE SYNTAX SwAuthUserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration information for an Authenticator Port." INDEX { swAuthUserName } ::= { swAuthUserTable 1 } SwAuthUserEntry ::= SEQUENCE { swAuthUserName SnmpAdminString, swAuthUserPassword DisplayString, swAuthUserStatus RowStatus } swAuthUserName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "The unique index value of a row in this table. This object is used to set 802.1X Local user name, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark." ::= { swAuthUserEntry 1 } swAuthUserPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set 802.1X Local user Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark." ::= { swAuthUserEntry 2 } swAuthUserStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row in the swAuthUserTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthUserName objects must be explicitly set." ::= { swAuthUserEntry 3 } -- ------------------------------------------------------------- -- groups in the Authentication RADIUS Server MIB -- ------------------------------------------------------------- swAuthRadiusServer OBJECT IDENTIFIER ::= { companyAuthGroup 4 } -- ----------------------------------------------------------------------------- -- swAuthRadiusServer -- ----------------------------------------------------------------------------- -- ----------------------------------------------------------------------------- -- swAuthRadiusServer for IPv6 -- ----------------------------------------------------------------------------- swAuthRadiusServerTable OBJECT-TYPE SYNTAX SEQUENCE OF SwAuthRadiusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself." ::= { swAuthRadiusServer 2 } swAuthRadiusServerEntry OBJECT-TYPE SYNTAX SwAuthRadiusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration information for an Authenticator Port." INDEX { swAuthRadiusServerIndex } ::= { swAuthRadiusServerTable 1 } SwAuthRadiusServerEntry ::= SEQUENCE { swAuthRadiusServerIndex INTEGER, swAuthRadiusIPType INTEGER, swAuthRadiusServerAddress Ipv6Address, swAuthRadiusServerInterfaceName OCTET STRING, swAuthRadiusServerAuthenticationPort INTEGER, swAuthRadiusServerAccountingPort INTEGER, swAuthRadiusServerTimeout INTEGER, swAuthRadiusServerRetransmit INTEGER, swAuthRadiusServerKey DisplayString, swAuthRadiusServerStatus RowStatus } swAuthRadiusServerIndex OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3." ::= { swAuthRadiusServerEntry 1 } swAuthRadiusIPType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the RADIUS server IP type referred to in this table entry." DEFVAL { 1 } ::= { swAuthRadiusServerEntry 2 } swAuthRadiusServerAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the RADIUS server referred to in this table entry." ::= { swAuthRadiusServerEntry 3 } swAuthRadiusServerInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the interface name when the swAuthRadiusServerAddress is linklocal address." ::= { swAuthRadiusServerEntry 4 } swAuthRadiusServerAuthenticationPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value is for setting UDP Port." DEFVAL { 1812 } ::= { swAuthRadiusServerEntry 5 } swAuthRadiusServerAccountingPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value is for setting UDP Port." DEFVAL { 1813 } ::= { swAuthRadiusServerEntry 6 } swAuthRadiusServerTimeout OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The value is for setting UDP Port." DEFVAL { 5 } ::= { swAuthRadiusServerEntry 7 } swAuthRadiusServerRetransmit OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The value is for setting UDP Port." DEFVAL { 2 } ::= { swAuthRadiusServerEntry 8 } swAuthRadiusServerKey OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark." ::= { swAuthRadiusServerEntry 9 } swAuthRadiusServerStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthRadiusServerIndex objects must be explicitly set." ::= { swAuthRadiusServerEntry 10 } -- ------------------------------------------------------------------ -- QoS -- ------------------------------------------------------------------ qosMode OBJECT-TYPE SYNTAX INTEGER { dot1p(1), dscp(2), tos(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Settings of Qos mode: IEEE 802.1p QoS or DSCP QoS or TOS Qos. IEEE 802.1p : It specifies a priority(0~7) value to four queues in WS3 : Low(1,2), Medium(0,3), High(4,5) and Highest(6,7), inclusive that can be used by Quality of Service (QoS) disciplines to differentiate traffic. DSCP : Differentiated services enhancements to the Internet protocol are intended to enable scalable service discrimination in the Internet without the need for per-flow state and signaling at every hop. " ::= { companyQoSGroup 1 } queuingMechanism OBJECT-TYPE SYNTAX INTEGER { strictPriority(1), wrr(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority scheduler node that is stacked directly above the port. Queues stacked on top of the strict-priority scheduler node always get bandwidth before other queues. Weighted round-robin scheduling is designed to better handle queues with different processing capacities. Each queue has a weight : Low is 1, Medium is 2, High is 4 and Highest is 8 for WS4 spec. Queues with higher weights get bandwidth before than other queues with less weights. " ::= { companyQoSGroup 2 } -- ------------------------------------------------------------------ -- QoS -- ------------------------------------------------------------------ qosQ1p OBJECT IDENTIFIER ::= { companyQoSGroup 3 } dot1pPortTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1pPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of 802.1p port default priority Entries." ::= { qosQ1p 1 } dot1pPortEntry OBJECT-TYPE SYNTAX Dot1pPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of 802.1p port default priority priorities." INDEX { dot1pPortIndex } ::= { dot1pPortTable 1 } Dot1pPortEntry ::= SEQUENCE { dot1pPortIndex INTEGER, dot1pPortPriority INTEGER } dot1pPortIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "A port identifier that is in the range of 1 to ifNumber." ::= { dot1pPortEntry 1 } dot1pPortPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For ingress tagged packets, D-Link Smart Switches will refer to their 802.1p information and prioritize them with 8 different priority queues. " ::= { dot1pPortEntry 2 } -- ------------------------------------------------------------------ -- QoS -- ------------------------------------------------------------------ qosDiffServ OBJECT IDENTIFIER ::= { companyQoSGroup 4 } qosDiffServEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Display the DSCP(Differentiated services) function Enabled or Disabled. Notice : DiffServ Type is 2~7 bits in the TOS field. ex: If the DiffServ Type = 000011(3), the value in TOS field is 00001100(12) " ::= { qosDiffServ 1 } qosDiffServTypeGroup OBJECT IDENTIFIER ::= { qosDiffServ 2 } qosDiffServType00 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 0 : IP ToS value = 0" ::= { qosDiffServTypeGroup 1 } qosDiffServType01 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 01 : IP ToS value = 4" ::= { qosDiffServTypeGroup 2 } qosDiffServType02 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 02 : IP ToS value = 8" ::= { qosDiffServTypeGroup 3 } qosDiffServType03 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 03 : IP ToS value = 12" ::= { qosDiffServTypeGroup 4 } qosDiffServType04 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 04 : IP ToS value = 16" ::= { qosDiffServTypeGroup 5 } qosDiffServType05 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 05 : IP ToS value = 20" ::= { qosDiffServTypeGroup 6 } qosDiffServType06 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 06 : IP ToS value = 24" ::= { qosDiffServTypeGroup 7 } qosDiffServType07 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 07 : IP ToS value = 28" ::= { qosDiffServTypeGroup 8 } qosDiffServType08 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 08 : IP ToS value = 32" ::= { qosDiffServTypeGroup 9 } qosDiffServType09 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 09 : IP ToS value = 36" ::= { qosDiffServTypeGroup 10 } qosDiffServType10 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 10 : IP ToS value = 40" ::= { qosDiffServTypeGroup 11 } qosDiffServType11 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 11 : IP ToS value = 44" ::= { qosDiffServTypeGroup 12 } qosDiffServType12 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 12 : IP ToS value = 48" ::= { qosDiffServTypeGroup 13 } qosDiffServType13 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 13 : IP ToS value = 52" ::= { qosDiffServTypeGroup 14 } qosDiffServType14 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 14 : IP ToS value = 56" ::= { qosDiffServTypeGroup 15 } qosDiffServType15 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 15 : IP ToS value = 60" ::= { qosDiffServTypeGroup 16 } qosDiffServType16 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 16 : IP ToS value = 64" ::= { qosDiffServTypeGroup 17 } qosDiffServType17 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 17 : IP ToS value = 68" ::= { qosDiffServTypeGroup 18 } qosDiffServType18 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 18 : IP ToS value = 72" ::= { qosDiffServTypeGroup 19 } qosDiffServType19 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 19 : IP ToS value = 76" ::= { qosDiffServTypeGroup 20 } qosDiffServType20 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 20 : IP ToS value = 80" ::= { qosDiffServTypeGroup 21 } qosDiffServType21 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 21 : IP ToS value = 84" ::= { qosDiffServTypeGroup 22 } qosDiffServType22 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 22 : IP ToS value = 88" ::= { qosDiffServTypeGroup 23 } qosDiffServType23 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 23 : IP ToS value = 92" ::= { qosDiffServTypeGroup 24 } qosDiffServType24 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 24 : IP ToS value = 96" ::= { qosDiffServTypeGroup 25 } qosDiffServType25 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 25 : IP ToS value = 100" ::= { qosDiffServTypeGroup 26 } qosDiffServType26 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 26 : IP ToS value = 104" ::= { qosDiffServTypeGroup 27 } qosDiffServType27 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 27 : IP ToS value = 108" ::= { qosDiffServTypeGroup 28 } qosDiffServType28 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 28 : IP ToS value = 112" ::= { qosDiffServTypeGroup 29 } qosDiffServType29 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 29 : IP ToS value = 116" ::= { qosDiffServTypeGroup 30 } qosDiffServType30 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 30 : IP ToS value = 120" ::= { qosDiffServTypeGroup 31 } qosDiffServType31 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 31 : IP ToS value = 124" ::= { qosDiffServTypeGroup 32 } qosDiffServType32 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 32 : IP ToS value = 128" ::= { qosDiffServTypeGroup 33 } qosDiffServType33 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 33 : IP ToS value = 132" ::= { qosDiffServTypeGroup 34 } qosDiffServType34 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 34 : IP ToS value = 136" ::= { qosDiffServTypeGroup 35 } qosDiffServType35 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 35 : IP ToS value = 140" ::= { qosDiffServTypeGroup 36 } qosDiffServType36 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 36 : IP ToS value = 144" ::= { qosDiffServTypeGroup 37 } qosDiffServType37 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 37 : IP ToS value = 148" ::= { qosDiffServTypeGroup 38 } qosDiffServType38 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 38 : IP ToS value = 152" ::= { qosDiffServTypeGroup 39 } qosDiffServType39 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 39 : IP ToS value = 156" ::= { qosDiffServTypeGroup 40 } qosDiffServType40 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 40 : IP ToS value = 160" ::= { qosDiffServTypeGroup 41 } qosDiffServType41 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 41 : IP ToS value = 164" ::= { qosDiffServTypeGroup 42 } qosDiffServType42 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 42 : IP ToS value = 168" ::= { qosDiffServTypeGroup 43 } qosDiffServType43 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 43 : IP ToS value = 172" ::= { qosDiffServTypeGroup 44 } qosDiffServType44 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 44 : IP ToS value = 176" ::= { qosDiffServTypeGroup 45 } qosDiffServType45 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 45 : IP ToS value = 180" ::= { qosDiffServTypeGroup 46 } qosDiffServType46 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 46 : IP ToS value = 184" ::= { qosDiffServTypeGroup 47 } qosDiffServType47 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 47 : IP ToS value = 188" ::= { qosDiffServTypeGroup 48 } qosDiffServType48 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 48 : IP ToS value = 192" ::= { qosDiffServTypeGroup 49 } qosDiffServType49 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 49 : IP ToS value = 196" ::= { qosDiffServTypeGroup 50 } qosDiffServType50 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 50 : IP ToS value = 200" ::= { qosDiffServTypeGroup 51 } qosDiffServType51 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 51 : IP ToS value = 204" ::= { qosDiffServTypeGroup 52 } qosDiffServType52 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 52 : IP ToS value = 208" ::= { qosDiffServTypeGroup 53 } qosDiffServType53 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 53 : IP ToS value = 212" ::= { qosDiffServTypeGroup 54 } qosDiffServType54 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 54 : IP ToS value = 216" ::= { qosDiffServTypeGroup 55 } qosDiffServType55 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 55 : IP ToS value = 220" ::= { qosDiffServTypeGroup 56 } qosDiffServType56 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 56 : IP ToS value = 224" ::= { qosDiffServTypeGroup 57 } qosDiffServType57 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 57 : IP ToS value = 228" ::= { qosDiffServTypeGroup 58 } qosDiffServType58 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 58 : IP ToS value = 232" ::= { qosDiffServTypeGroup 59 } qosDiffServType59 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 59 : IP ToS value = 236" ::= { qosDiffServTypeGroup 60 } qosDiffServType60 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 60 : IP ToS value = 240" ::= { qosDiffServTypeGroup 61 } qosDiffServType61 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 61 : IP ToS value = 244" ::= { qosDiffServTypeGroup 62 } qosDiffServType62 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 62 : IP ToS value = 248" ::= { qosDiffServTypeGroup 63 } qosDiffServType63 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 63 : IP ToS value = 252" ::= { qosDiffServTypeGroup 64 } -- ------------------------------------------------------------------ -- QoS -- ------------------------------------------------------------------ qosTOS OBJECT IDENTIFIER ::= { companyQoSGroup 5 } qosTOSEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Display the TOS(Type of services) function Enabled or Disabled." ::= { qosTOS 1 } qosTOSGroup OBJECT IDENTIFIER ::= { qosTOS 2 } qosTOSType00 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 0" ::= { qosTOSGroup 1 } qosTOSType01 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 01" ::= { qosTOSGroup 2 } qosTOSType02 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 02" ::= { qosTOSGroup 3 } qosTOSType03 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 03" ::= { qosTOSGroup 4 } qosTOSType04 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 04" ::= { qosTOSGroup 5 } qosTOSType05 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 05" ::= { qosTOSGroup 6 } qosTOSType06 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 06" ::= { qosTOSGroup 7 } qosTOSType07 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 07" ::= { qosTOSGroup 8 } -- ---------------------------------------------------------- -- The companyTrafficMgmt Groups -- ---------------------------------------------------------- -- Bandwidth Control Group --------------------------------------------- -- bandwidthCtrlSettings OBJECT IDENTIFIER ::= { companyTrafficMgmt 1 } bandwidthCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF BandwidthCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control the rate limiting parameters either for the entire switch or for each interface in the switch." ::= { bandwidthCtrlSettings 2 } bandwidthCtrlEntry OBJECT-TYPE SYNTAX BandwidthCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each physical interface in the switch." INDEX { bandwidthCtrlIndex } ::= { bandwidthCtrlTable 1 } BandwidthCtrlEntry ::= SEQUENCE { bandwidthCtrlIndex Integer32, bandwidthCtrlTxThreshold Integer32, bandwidthCtrlRxThreshold Integer32 } bandwidthCtrlIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index for which the configuration in this entry applies." ::= { bandwidthCtrlEntry 1 } bandwidthCtrlTxThreshold OBJECT-TYPE SYNTAX Integer32 (0 | 64..1024000) MAX-ACCESS read-write STATUS current DESCRIPTION "Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. The value can be set between 64~1024000(Kbits per second) in FE port, 64~1024000 (Kbits per second) in GE port." ::= { bandwidthCtrlEntry 2 } bandwidthCtrlRxThreshold OBJECT-TYPE SYNTAX Integer32 (0 | 64..1024000) MAX-ACCESS read-write STATUS current DESCRIPTION "Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware. The value can be set between 64~1024000(Kbits per second) in FE port, 64~1024000(Kbits per second) in GE port." ::= { bandwidthCtrlEntry 3} -- Broadcast Storm Control Group --------------------------------------------- -- -- Broadcast Storm Control broadcastStormCtrlSettings OBJECT IDENTIFIER ::= { companyTrafficMgmt 3 } broadcastStormCtrlGlobalOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates storm control function is enabled or disabled for device. When you enable broadcast storm control function, D-Link Smart Switches will allowed you to limit the number of broadcast packets per second going through device." ::= { broadcastStormCtrlSettings 1 } broadcastStormCtrlLimitType OBJECT-TYPE SYNTAX INTEGER { broadcastonly(1), multicastAndbroadcast(2), dlfMulticastAndbroadcast(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates storm control function is control broadcast packet or multicast packet or dlf packet." ::= { broadcastStormCtrlSettings 2 } broadcastStormCtrlThreshold OBJECT-TYPE SYNTAX Integer32 (0 | 64..1024000) MAX-ACCESS read-write STATUS current DESCRIPTION "Allows to configure the limiting value for the maximum number of Kbits/sec that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting on this interface. The value that can be set for this object is limited by the underlying hardware. The limit value must be between 64~1024000(Kbits per second) in FE port, 64~1024000(Kbits per second) in GE port, and limit value is multiple of 64. (Notice : if the limit value is 0, it means unlimited.)" DEFVAL {0} ::= { broadcastStormCtrlSettings 3 } -- ------------------------------------------------------------------ -- companySecurity -- ------------------------------------------------------------------ -- Trusted Host securityTrustedHost OBJECT IDENTIFIER ::= { companySecurity 1 } trustedHostStatus OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which you trust to access and control the switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection." DEFVAL { disabled } ::= { securityTrustedHost 1 } -- ipv6 trustedHostTable OBJECT-TYPE SYNTAX SEQUENCE OF TrustedHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to configure trusted host for in the system." ::= { securityTrustedHost 3 } trustedHostEntry OBJECT-TYPE SYNTAX TrustedHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents rules for particular trusted host." INDEX { trustedHostIPType, trustedHostIpAddr, trustedHostIpMask } ::= { trustedHostTable 1 } TrustedHostEntry ::= SEQUENCE { trustedHostIPType INTEGER, trustedHostIpAddr DisplayString, trustedHostIpMask DisplayString, trustedHostRowStatus RowStatus } trustedHostIPType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of IP interface." ::= { trustedHostEntry 1 } trustedHostIpAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of host you allow to access to D-Link Smart Switch. Your local host IPv4/6 Addresses must be one of the IP Addresses to avoid disconnection." ::= { trustedHostEntry 2 } trustedHostIpMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Used to mask with IPv4/6 address, it allow you set a subnet as a trusted host entry." ::= { trustedHostEntry 3 } trustedHostRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. IPv4 Trust Host created example: 1.4.¡¨IPv4 address¡¨.4.¡¨mask¡¨ IPv6 Trust Host created example: 2.16.¡¨IPv6 address¡¨.1.¡¨prefix¡¨" ::= { trustedHostEntry 4 } securityARPSpoofPrevent OBJECT IDENTIFIER ::= { companySecurity 3} -- aRPSpoofPrevent Control Table aRPSpoofPreventTable OBJECT-TYPE SYNTAX SEQUENCE OF ARPSpoofPreventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control ARP Spoofing prevention for the entire switch or for each interface in the switch." ::= { securityARPSpoofPrevent 1 } aRPSpoofPreventEntry OBJECT-TYPE SYNTAX ARPSpoofPreventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system." INDEX { aRPSpoofPreventIpAddr } ::= { aRPSpoofPreventTable 1 } ARPSpoofPreventEntry ::= SEQUENCE { aRPSpoofPreventIpAddr IpAddress, aRPSpoofPreventMacAddress MacAddress, aRPSpoofPreventPortList PortList, aRPSpoofPreventRowStatus RowStatus } aRPSpoofPreventIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'." ::= { aRPSpoofPreventEntry 1 } aRPSpoofPreventMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Ethernet Mac Address." DEFVAL { '000102030405'h } ::= { aRPSpoofPreventEntry 2 } aRPSpoofPreventPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports." ::= { aRPSpoofPreventEntry 3 } aRPSpoofPreventRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { aRPSpoofPreventEntry 4 } -- ------------------------------------------------------------------ -- companySecurity -- ------------------------------------------------------------------ securitySSL OBJECT IDENTIFIER ::= { companySecurity 5 } sslSecurityHttpStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling secure HTTP in the system." DEFVAL { disable } ::= { securitySSL 1 } sslCiphers OBJECT IDENTIFIER ::= { securitySSL 2 } sslCipherSuiteList OBJECT-TYPE SYNTAX BITS { rsa-null-md5(0), rsa-null-sha(1), rsa-des-sha(2), rsa-3des-sha(3), dh-rsa-des-sha(4), dh-rsa-3des-sha(5), rsa-exp1024-des-sha(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is to configure the cipher-suites list." ::= { sslCiphers 1} -- ------------------------------------------------------------------ -- companySecurity -- ------------------------------------------------------------------ securitySSH OBJECT IDENTIFIER ::= { companySecurity 8 } sshSecurityStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling ssh in the system." DEFVAL { disable } ::= { securitySSH 1} sshMaxAuthFailAttempts OBJECT-TYPE SYNTAX INTEGER (2..20) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the max auth fail retry attempt times." ::= {securitySSH 2} sshSessionKeyRekeying OBJECT-TYPE SYNTAX INTEGER { never(0), ten-min(1), thirty-min(2), sixty-min(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates one SSH session rekey time interval." ::= {securitySSH 3} sshMaxSession OBJECT-TYPE SYNTAX INTEGER (1..4) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates max SSH session number supported in system." ::= {securitySSH 4} sshConnectionTimeout OBJECT-TYPE SYNTAX INTEGER (120..600) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates SSH connection timeout value." ::= {securitySSH 5} --************************************************************************ -- SSH encryption algorithm group configuration --************************************************************************ sshAuthenMethodPassWordAdmin OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates authen method password is enabled or disabled." ::= {securitySSH 6} sshAuthenMethodPubKeyAdmin OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates authen method public-key is enabled or disabled." ::= {securitySSH 7} sshAuthenMethodHostKeyAdmin OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates authen method host-key is enabled or disabled." ::= {securitySSH 8} sshCipherSuiteList OBJECT-TYPE SYNTAX BITS { tripleDESCBC(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object is to configure the cipher-suites list." ::= { securitySSH 9} sshMacSuiteList OBJECT-TYPE SYNTAX BITS { hMAC-SHA1(0), hMAC-MD5(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is to configure the MAC-list." ::= { securitySSH 10} sshPublKeyRSAAdmin OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates Public key generating algorithm RSA is enabled or disabled." ::= {securitySSH 11} --************************************************************************ -- SSH User Auth Info. --************************************************************************ sshUserInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF SshUserInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to configure SSH user auth in the system." ::= { securitySSH 12 } sshUserInfoEntry OBJECT-TYPE SYNTAX SshUserInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry to configure user auth in the system." INDEX { sshUserInfoID } ::= { sshUserInfoTable 1 } SshUserInfoEntry ::= SEQUENCE { sshUserInfoID Integer32, sshUserInfoUserName DisplayString, sshUserInfoAuth INTEGER, sshUserInfoHostName DisplayString, sshUserInfoHostIp IpAddress, sshUserInfoHostIpv6 Ipv6Address } sshUserInfoID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ssh user ID associated with the SSH user Info. entry (ID number of SSH user)." ::= { sshUserInfoEntry 1 } sshUserInfoUserName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The ssh user name associated with the SSH user Info. entry (e.g., `admin, user')." ::= { sshUserInfoEntry 2} sshUserInfoAuth OBJECT-TYPE SYNTAX INTEGER { publickey(4), password(2), hostbased(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object indicates which auth used by the user." ::= {sshUserInfoEntry 3} sshUserInfoHostName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The ssh host name associated with the SSH user Info. entry (e.g., `DUT1, DUT2')." ::= { sshUserInfoEntry 4} sshUserInfoHostIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "SSH HostBased IP Address of the system. Set '0.0.0.0' to disable SSH hostBased IP address check." ::= { sshUserInfoEntry 5 } sshUserInfoHostIpv6 OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "SSH HostBased IPv6 Address of the system. Set '0000:0000:0000:0000:0000:0000:0000:0000' or empty string to disable SSH hostBased IPv6 address check." ::= { sshUserInfoEntry 6 } -- ---------------------------------------------------------- -- The companySecurity Groups -- ---------------------------------------------------------- securityPortSecurity OBJECT IDENTIFIER ::= { companySecurity 2 } -- Port Security Group --------------------------------------------- -- portSecTable OBJECT-TYPE SYNTAX SEQUENCE OF PortSecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control port security features of the device." ::= { securityPortSecurity 1 } portSecEntry OBJECT-TYPE SYNTAX PortSecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in port security table for each interface in the system." INDEX { portSecIndex } ::= { portSecTable 1 } PortSecEntry ::= SEQUENCE { portSecIndex Integer32, portSecState INTEGER, portSecMLA Integer32 } portSecIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index for which the configuration in this entry applies." ::= { portSecEntry 1 } portSecState OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled." ::= { portSecEntry 2 } portSecMLA OBJECT-TYPE SYNTAX Integer32 (0..64) MAX-ACCESS read-write STATUS current DESCRIPTION "Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number. The number can be set 0 to 64. Note: Set value 0 means cannot learn MAC address." ::= {portSecEntry 3} -- ---------------------------------------------------------- -- The companyCableDiagnostic Groups -- ---------------------------------------------------------- -- Cable Diagnostics Group --------------------------------------------- -- cableDiagTriggerIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Trigger an interface index to do cable diagnostic." ::= {companyCableDiagnostic 1 } cableDiagPair1TestResult OBJECT-TYPE SYNTAX INTEGER { ok (0), open (1), short (2), open-short (3), crosstalk (4), mismatch (5), linedriver (6), notAvailable (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 1 test result." ::= {companyCableDiagnostic 2 } cableDiagPair1FaultDistance OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Cable Diagnostics pair 1 fault distance." ::= {companyCableDiagnostic 3} cableDiagPair2TestResult OBJECT-TYPE SYNTAX INTEGER { ok (0), open (1), short (2), open-short (3), crosstalk (4), mismatch (5), linedriver (6), notAvailable (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 2 test result." ::= {companyCableDiagnostic 4 } cableDiagPair2FaultDistance OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 2 fault distance." ::= {companyCableDiagnostic 5} cableDiagPair3TestResult OBJECT-TYPE SYNTAX INTEGER { ok (0), open (1), short (2), open-short (3), crosstalk (4), mismatch (5), linedriver (6), notAvailable (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 3 test result." ::= {companyCableDiagnostic 6 } cableDiagPair3FaultDistance OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 3 fault distance." ::= {companyCableDiagnostic 7} cableDiagPair4TestResult OBJECT-TYPE SYNTAX INTEGER { ok (0), open (1), short (2), open-short (3), crosstalk (4), mismatch (5), linedriver (6), notAvailable (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 4 test result." ::= {companyCableDiagnostic 8 } cableDiagPair4FaultDistance OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 4 fault distance." ::= {companyCableDiagnostic 9} cableDiagLengthinRange OBJECT-TYPE SYNTAX INTEGER { less50 (1), from50to80 (2), from80to100 (3), from100to140 (4), notAvailable (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics length when link up in speed 1G. (Display in range)" ::= {companyCableDiagnostic 10} -- ------------------------------------------------------------------ -- companyACLGroup -- ------------------------------------------------------------------ -- ------------------------------------------------------------------ -- companyACLGroup (15) -- ------------------------------------------------------------------ aclProfile OBJECT IDENTIFIER ::= { companyACLGroup 1 } aclProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AclProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A table to ACL profile . " ::= { aclProfile 1 } aclProfileEntry OBJECT-TYPE SYNTAX AclProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Each entry in this table is a ACL profile. Index to the table is ACL profile ID. " INDEX { aclProfileNo} ::= { aclProfileTable 1 } AclProfileEntry ::= SEQUENCE { aclProfileNo Integer32, aclProfileName SnmpAdminString, aclProfileType INTEGER, aclProfileRuleCount Integer32, aclProfileStatus RowStatus } aclProfileNo OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS read-only STATUS current DESCRIPTION "The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only." ::= { aclProfileEntry 1 } aclProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "An administratively assigned string, which may be used to identify the Profile." ::= { aclProfileEntry 2 } aclProfileType OBJECT-TYPE SYNTAX INTEGER { l2 (1), l3v4 (2), l3v4Ext(13), l3v6 (11) } MAX-ACCESS read-write STATUS current DESCRIPTION "The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3v4 (2) - for IPv4-based rule, l3v4Ext (3) - for IPv4-Ext rule, l3v6 (4) - for IPv6-based rule. Note that only l2, l3 and l3v6 could be set by user, other is reserved for system to show information. " ::= { aclProfileEntry 3 } aclProfileRuleCount OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of rules in this profile." ::= { aclProfileEntry 4 } aclProfileStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION " This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted. " ::= { aclProfileEntry 14 } -- L2 Filter Group -------------------------------------------------- aclL2Rule OBJECT IDENTIFIER ::= { companyACLGroup 2 } aclL2RuleTable OBJECT-TYPE SYNTAX SEQUENCE OF AclL2RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to configure L2 filter rules in the system." ::= { aclL2Rule 1 } aclL2RuleEntry OBJECT-TYPE SYNTAX AclL2RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID." INDEX { aclL2ProfileID , aclL2AccessID } ::= { aclL2RuleTable 1 } AclL2RuleEntry ::= SEQUENCE { aclL2AccessID Integer32, aclL2ProfileID Integer32, aclL2RuleEtherType Integer32, aclL2RuleDstMacAddr MacAddress, aclL2RuleSrcMacAddr MacAddress, aclL2RuleVlanId Integer32, aclL2Rule1pPriority Integer32, aclL2RuleDstMacAddrMask MacAddress, aclL2RuleSrcMacAddrMask MacAddress, aclL2RuleAction INTEGER, aclL2RulePriority INTEGER, aclL2RuleReplacePriority INTEGER, aclL2RuleStatus RowStatus } aclL2AccessID OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "L2 Filter rule ID." ::= { aclL2RuleEntry 1 } aclL2ProfileID OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS read-only STATUS current DESCRIPTION "ACL Profile ID which this rule join." DEFVAL { 1 } ::= { aclL2RuleEntry 2 } aclL2RuleEtherType OBJECT-TYPE SYNTAX Integer32 (-1 | 1501..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition. The aclL2EtherFrameType should be specified as ether-type." DEFVAL { -1 } ::= { aclL2RuleEntry 3 } aclL2RuleDstMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition." ::= { aclL2RuleEntry 4 } aclL2RuleSrcMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address" ::= { aclL2RuleEntry 5 } aclL2RuleVlanId OBJECT-TYPE SYNTAX Integer32 (-1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL2RuleEntry 6 } aclL2Rule1pPriority OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL2RuleEntry 7 } aclL2RuleDstMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The MAC address Mask work for Destination MAC address." ::= { aclL2RuleEntry 8 } aclL2RuleSrcMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The MAC address Mask work for Source MAC address." ::= { aclL2RuleEntry 9 } aclL2RuleAction OBJECT-TYPE SYNTAX INTEGER { allow (1), drop (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded." DEFVAL { allow } ::= { aclL2RuleEntry 10 } aclL2RulePriority OBJECT-TYPE SYNTAX INTEGER (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Enter a priority value if you want to re-write the 802.1p user priority of a packet to the value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue.By Default, the value will be '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL2RuleEntry 12 } aclL2RuleReplacePriority OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable this option and manually enter the replacement value used to re-write the 802.1p user priority value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue. Otherwise, a packet will have its incoming 802.1p user priority re-written to its original value before being forwarded by the Switch." DEFVAL { disabled } ::= { aclL2RuleEntry 13 } aclL2RuleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aclL2RuleEntry 99 } -- L3 Filter Group -------------------------------------------------- aclL3v4Rule OBJECT IDENTIFIER ::= { companyACLGroup 3 } aclL3v4RuleTable OBJECT-TYPE SYNTAX SEQUENCE OF AclL3v4RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A table to configure L3 filter rules in the system. " ::= { aclL3v4Rule 1 } aclL3v4RuleEntry OBJECT-TYPE SYNTAX AclL3v4RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Each entry in this table is a L3 filter rule. Index to the table is L3 filter number. " INDEX { aclL3v4RuleProfileNo, aclL3v4RuleAccessID } ::= { aclL3v4RuleTable 1 } AclL3v4RuleEntry ::= SEQUENCE { aclL3v4RuleAccessID Integer32, aclL3v4RuleProfileNo Integer32, aclL3v4RuleDstIpAddr IpAddress, aclL3v4RuleSrcIpAddr IpAddress, aclL3v4RuleDstIpAddrMask IpAddress, aclL3v4RuleSrcIpAddrMask IpAddress, aclL3v4RuleAction INTEGER, aclL3v4RulePriority INTEGER, aclL3v4RuleReplacePriority INTEGER, aclL3v4RuleStatus RowStatus } aclL3v4RuleAccessID OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "L3 Filter rule ID." ::= { aclL3v4RuleEntry 1 } aclL3v4RuleProfileNo OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS read-only STATUS current DESCRIPTION "The Profile ID which this rule join." ::= { aclL3v4RuleEntry 2 } aclL3v4RuleDstIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition." DEFVAL { '00000000'h } ::= { aclL3v4RuleEntry 3 } aclL3v4RuleSrcIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition." DEFVAL { '00000000'h } ::= { aclL3v4RuleEntry 4 } aclL3v4RuleDstIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP subnet mask for Destination IP address." DEFVAL { 'FFFFFFFF'h } ::= { aclL3v4RuleEntry 5 } aclL3v4RuleSrcIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP subnet mask for Source IP address." DEFVAL { 'FFFFFFFF'h } ::= { aclL3v4RuleEntry 6 } aclL3v4RuleAction OBJECT-TYPE SYNTAX INTEGER { allow (1), drop (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to be taken on the packet if the filter rule matches." DEFVAL { allow } ::= { aclL3v4RuleEntry 7 } aclL3v4RulePriority OBJECT-TYPE SYNTAX INTEGER (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Enter a priority value if you want to re-write the 802.1p user priority of a packet to the value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue.By Default, the value will be '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3v4RuleEntry 9 } aclL3v4RuleReplacePriority OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable this option and manually enter the replacement value used to re-write the 802.1p user priority value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue. Otherwise, a packet will have its incoming 802.1p user priority re-written to its original value before being forwarded by the Switch." DEFVAL { disabled } ::= { aclL3v4RuleEntry 10 } aclL3v4RuleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aclL3v4RuleEntry 99 } -- L3v4 Ext Filter Group -------------------------------------------------- aclL3v4ExtRule OBJECT IDENTIFIER ::= { companyACLGroup 4 } aclL3v4ExtRuleTable OBJECT-TYPE SYNTAX SEQUENCE OF AclL3v4ExtRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A table to configure L3 filter rules in the system. " ::= { aclL3v4ExtRule 1 } aclL3v4ExtRuleEntry OBJECT-TYPE SYNTAX AclL3v4ExtRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Each entry in this table is a L3 filter rule. Index to the table is L3 filter number. " INDEX { aclL3v4ExtRuleProfileNo, aclL3v4ExtRuleAccessID } ::= { aclL3v4ExtRuleTable 1 } AclL3v4ExtRuleEntry ::= SEQUENCE { aclL3v4ExtRuleAccessID Integer32, aclL3v4ExtRuleProfileNo Integer32, aclL3v4ExtRuleProtocol INTEGER, aclL3v4ExtRuleICMPMessageType Integer32, aclL3v4ExtRuleICMPMessageCode Integer32, aclL3v4ExtRuleDstIpAddr IpAddress, aclL3v4ExtRuleSrcIpAddr IpAddress, aclL3v4ExtRuleDstIpAddrMask IpAddress, aclL3v4ExtRuleSrcIpAddrMask IpAddress, aclL3v4ExtRuleTcpUdpDstPort Integer32, aclL3v4ExtRuleTcpUdpSrcPort Integer32, aclL3v4ExtRuleTcpUdpDstPortMask OCTET STRING, aclL3v4ExtRuleTcpUdpSrcPortMask OCTET STRING, aclL3v4ExtRuleDscp Integer32, aclL3v4ExtRuleToS Integer32, aclL3v4ExtRuleIgmpType Integer32, aclL3v4ExtRuleProtocolId INTEGER, aclL3v4ExtRuleAction INTEGER, aclL3v4ExtRulePriority INTEGER, aclL3v4ExtRuleReplacePriority INTEGER, aclL3v4ExtRuleStatus RowStatus } aclL3v4ExtRuleAccessID OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "L3 Filter rule ID." ::= { aclL3v4ExtRuleEntry 1 } aclL3v4ExtRuleProfileNo OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS read-only STATUS current DESCRIPTION "The Profile ID which this rule join." ::= { aclL3v4ExtRuleEntry 2 } aclL3v4ExtRuleProtocol OBJECT-TYPE SYNTAX INTEGER { none(0), icmp(1), igmp(2), tcp(6), udp(17), protocolid(24) } MAX-ACCESS read-write STATUS current DESCRIPTION " The type of protocol to be checked against the packet." DEFVAL { 0 } ::= { aclL3v4ExtRuleEntry 3 } aclL3v4ExtRuleICMPMessageType OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18), " DEFVAL { -1 } ::= { aclL3v4ExtRuleEntry 4 } aclL3v4ExtRuleICMPMessageCode OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12), " DEFVAL { -1 } ::= { aclL3v4ExtRuleEntry 5 } aclL3v4ExtRuleDstIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition." DEFVAL { '00000000'h } ::= { aclL3v4ExtRuleEntry 6 } aclL3v4ExtRuleSrcIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition." DEFVAL { '00000000'h } ::= { aclL3v4ExtRuleEntry 7 } aclL3v4ExtRuleDstIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP subnet mask for Destination IP address." DEFVAL { 'FFFFFFFF'h } ::= { aclL3v4ExtRuleEntry 8 } aclL3v4ExtRuleSrcIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP subnet mask for Source IP address." DEFVAL { 'FFFFFFFF'h } ::= { aclL3v4ExtRuleEntry 9 } aclL3v4ExtRuleTcpUdpDstPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3v4ExtRuleEntry 10 } aclL3v4ExtRuleTcpUdpSrcPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP source port. The default value is -1, which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3v4ExtRuleEntry 11 } aclL3v4ExtRuleTcpUdpDstPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP Destination port Mask." ::= { aclL3v4ExtRuleEntry 12 } aclL3v4ExtRuleTcpUdpSrcPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP Source port Mask." ::= { aclL3v4ExtRuleEntry 13 } aclL3v4ExtRuleDscp OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-create STATUS current DESCRIPTION "The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. The aclL3RuleTos should be specified as dscp." DEFVAL { -1 } ::= { aclL3v4ExtRuleEntry 20 } aclL3v4ExtRuleToS OBJECT-TYPE SYNTAX Integer32 (-1..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The ToS value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. The cmAclL3RuleTos should be specified as dscp." DEFVAL { -1 } ::= { aclL3v4ExtRuleEntry 21 } aclL3v4ExtRuleIgmpType OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3v4ExtRuleEntry 22 } aclL3v4ExtRuleProtocolId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the protocol id. The aclL3RuleProtocol should be specified as protocol-id." ::= { aclL3v4ExtRuleEntry 26 } aclL3v4ExtRuleAction OBJECT-TYPE SYNTAX INTEGER { allow (1), drop (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to be taken on the packet if the filter rule matches." DEFVAL { allow } ::= { aclL3v4ExtRuleEntry 31 } aclL3v4ExtRulePriority OBJECT-TYPE SYNTAX INTEGER (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Enter a priority value if you want to re-write the 802.1p user priority of a packet to the value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue.By Default, the value will be '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3v4ExtRuleEntry 33 } aclL3v4ExtRuleReplacePriority OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable this option and manually enter the replacement value used to re-write the 802.1p user priority value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue. Otherwise, a packet will have its incoming 802.1p user priority re-written to its original value before being forwarded by the Switch." DEFVAL { disabled } ::= { aclL3v4ExtRuleEntry 34 } aclL3v4ExtRuleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aclL3v4ExtRuleEntry 99 } -- L3 Filter Group -------------------------------------------------- aclL3v6Rule OBJECT IDENTIFIER ::= { companyACLGroup 5 } aclL3v6RuleTable OBJECT-TYPE SYNTAX SEQUENCE OF AclL3v6RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A table to configure L3 ipv6 filter rules in the system." ::= { aclL3v6Rule 1 } aclL3v6RuleEntry OBJECT-TYPE SYNTAX AclL3v6RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Each entry in this table is a L3 ipv6 filter rule. Index to the table is L3 ipv6 filter number. " INDEX { aclL3v6RuleProfileNo, aclL3v6RuleAccessID } ::= { aclL3v6RuleTable 1 } AclL3v6RuleEntry ::= SEQUENCE { aclL3v6RuleAccessID Integer32, aclL3v6RuleProfileNo Integer32, aclL3v6RuleTrafficClass Integer32, aclL3v6RuleProtocol INTEGER, aclL3v6RuleProtocolId INTEGER, aclL3v6RuleTcpUdpDstPort Integer32, aclL3v6RuleTcpUdpSrcPort Integer32, aclL3v6RuleTcpUdpDstPortMask OCTET STRING, aclL3v6RuleTcpUdpSrcPortMask OCTET STRING, aclL3v6RuleICMPv6MessageType Integer32, aclL3v6RuleICMPv6MessageCode Integer32, aclL3v6RuleDstIpv6Addr Ipv6Address, aclL3v6RuleSrcIpv6Addr Ipv6Address, aclL3v6RuleDstIpv6AddrPrefixLen INTEGER, aclL3v6RuleSrcIpv6AddrPrefixLen INTEGER, aclL3v6RuleAction INTEGER, aclL3v6RulePriority INTEGER, aclL3v6RuleReplacePriority INTEGER, aclL3v6RuleStatus RowStatus } aclL3v6RuleAccessID OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "L3 Filter rule ID." ::= { aclL3v6RuleEntry 1 } aclL3v6RuleProfileNo OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS read-only STATUS current DESCRIPTION "The Profile ID which this rule join." ::= { aclL3v6RuleEntry 2 } aclL3v6RuleTrafficClass OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The Traffic Class value to be checked against the packet. A default value is '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3v6RuleEntry 3 } aclL3v6RuleProtocol OBJECT-TYPE SYNTAX INTEGER { none(0), tcp(6), udp(17), protocolid(24), icmpv6(25) -- ospfv3(26) } MAX-ACCESS read-write STATUS current DESCRIPTION " The type of protocol to be checked against the packet." DEFVAL { 0 } ::= { aclL3v6RuleEntry 4 } aclL3v6RuleProtocolId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the protocol id. The aclL3v6RuleProtocol should be specified as protocol-id." ::= { aclL3v6RuleEntry 5 } aclL3v6RuleTcpUdpDstPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3v6RuleEntry 6 } aclL3v6RuleTcpUdpSrcPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP source port. The default value is -1, which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3v6RuleEntry 7 } aclL3v6RuleTcpUdpDstPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP Destination port Mask." ::= { aclL3v6RuleEntry 8 } aclL3v6RuleTcpUdpSrcPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP Source port Mask." ::= { aclL3v6RuleEntry 9 } aclL3v6RuleICMPv6MessageType OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18), " DEFVAL { -1 } ::= { aclL3v6RuleEntry 10 } aclL3v6RuleICMPv6MessageCode OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12), " DEFVAL { -1 } ::= { aclL3v6RuleEntry 11 } aclL3v6RuleDstIpv6Addr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "Destination IPv6 address to be matched with the packet." ::= { aclL3v6RuleEntry 12 } aclL3v6RuleSrcIpv6Addr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "Source IPv6 address to be matched with the packet." ::= { aclL3v6RuleEntry 13 } aclL3v6RuleDstIpv6AddrPrefixLen OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The prefix length for Destination IPv6 address." DEFVAL { 0 } ::= { aclL3v6RuleEntry 14 } aclL3v6RuleSrcIpv6AddrPrefixLen OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The prefix length for Source IPv6 address." DEFVAL { 0 } ::= { aclL3v6RuleEntry 15 } aclL3v6RuleAction OBJECT-TYPE SYNTAX INTEGER { allow (1), drop (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to be taken on the packet if the filter rule matches." DEFVAL { allow } ::= { aclL3v6RuleEntry 90 } aclL3v6RulePriority OBJECT-TYPE SYNTAX INTEGER (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Enter a priority value if you want to re-write the 802.1p user priority of a packet to the value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue.By Default, the value will be '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3v6RuleEntry 92 } aclL3v6RuleReplacePriority OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable this option and manually enter the replacement value used to re-write the 802.1p user priority value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue. Otherwise, a packet will have its incoming 802.1p user priority re-written to its original value before being forwarded by the Switch." DEFVAL { disabled } ::= { aclL3v6RuleEntry 93 } aclL3v6RuleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aclL3v6RuleEntry 99 } -- Port Binding Group aclPortBindGroup OBJECT IDENTIFIER ::= { companyACLGroup 6 } aclPortGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF AclPortGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control the port group binding information of L2 Group, L3v4 Group, and L3v6 Group" ::= { aclPortBindGroup 1 } aclPortGroupEntry OBJECT-TYPE SYNTAX AclPortGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system. Index to the table is the interface index of the port." INDEX { aclPortIndex } ::= { aclPortGroupTable 1 } AclPortGroupEntry ::= SEQUENCE { aclPortIndex Integer32, aclPortL2ProfileNo Integer32, aclPortL3v4ProfileNo Integer32, aclPortL3v6ProfileNo Integer32 } aclPortIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface index of the port for the configuration in this entry applies." ::= { aclPortGroupEntry 1 } aclPortL2ProfileNo OBJECT-TYPE SYNTAX Integer32 (0..50) MAX-ACCESS read-write STATUS current DESCRIPTION "The L2 Profile ID which this port bind. zero means not configured." ::= { aclPortGroupEntry 2 } aclPortL3v4ProfileNo OBJECT-TYPE SYNTAX Integer32 (0..50) MAX-ACCESS read-write STATUS current DESCRIPTION "The L3v4 Profile ID which this port bind. zero means not configured." ::= { aclPortGroupEntry 3 } aclPortL3v6ProfileNo OBJECT-TYPE SYNTAX Integer32 (0..50) MAX-ACCESS read-write STATUS current DESCRIPTION "The L3v6 Profile ID which this port bind. zero means not configured." ::= { aclPortGroupEntry 4 } -- ACL Hardware Resource Status aclHWResourceStatus OBJECT IDENTIFIER ::= { companyACLGroup 8 } aclHWResourceStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AclHWResourceStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to display HW Resource Status." ::= { aclHWResourceStatus 1 } aclHWResourceStatusEntry OBJECT-TYPE SYNTAX AclHWResourceStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system. Index to the table is the HW profile index of the ACL." INDEX { aclHWProfileIndex } ::= { aclHWResourceStatusTable 1 } AclHWResourceStatusEntry ::= SEQUENCE { aclHWProfileIndex Integer32, aclAccessListNo DisplayString, aclResourceEntryCount Integer32 } aclHWProfileIndex OBJECT-TYPE SYNTAX Integer32 (1..6) MAX-ACCESS read-only STATUS current DESCRIPTION "HW profile index of the ACL for the configuration in this entry applies." ::= { aclHWResourceStatusEntry 1 } aclAccessListNo OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The profile name in this HW profile index." ::= { aclHWResourceStatusEntry 2 } aclResourceEntryCount OBJECT-TYPE SYNTAX Integer32 (0..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of entries in this HW profile index." ::= { aclHWResourceStatusEntry 3 } snmpGlobalState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling SNMP Community function." ::= { companySNMPV3 1 } snmpV3User OBJECT IDENTIFIER ::= { companySNMPV3 2 } snmpV3Group OBJECT IDENTIFIER ::= { companySNMPV3 3 } snmpV3ViewTree OBJECT IDENTIFIER ::= { companySNMPV3 4 } snmpV3Community OBJECT IDENTIFIER ::= { companySNMPV3 5 } snmpV3Host OBJECT IDENTIFIER ::= { companySNMPV3 6 } snmpV3EngineID OBJECT-TYPE SYNTAX SnmpEngineID MAX-ACCESS read-write STATUS current DESCRIPTION "An SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the value of the snmpEngineID of a remote SNMP engine with which this user can communicate." ::= { companySNMPV3 7 } snmpV3Trap OBJECT IDENTIFIER ::= { companySNMPV3 8 } -- ---------------------------------------------------------------- -- The snmpV3User group -- ---------------------------------------------------------------- snmpV3UserTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpV3UserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { snmpV3User 1 } snmpV3UserEntry OBJECT-TYPE SYNTAX SnmpV3UserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { snmpV3UserName , snmpV3UserVersion} ::= { snmpV3UserTable 1 } SnmpV3UserEntry ::= SEQUENCE { snmpV3UserName SnmpAdminString, snmpV3UserVersion INTEGER, snmpV3UserGroupName SnmpAdminString, snmpV3UserAuthProtocol INTEGER, snmpV3UserAuthProtocolPassword SnmpAdminString, snmpV3UserPrivProtocol INTEGER, snmpV3UserPrivProtocolPassword SnmpAdminString, snmpV3UserStatus RowStatus } snmpV3UserName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. " ::= { snmpV3UserEntry 1 } snmpV3UserVersion OBJECT-TYPE SYNTAX INTEGER { v1 (1), v2c (2), v3 (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. " ::= { snmpV3UserEntry 2 } snmpV3UserGroupName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable. " ::= { snmpV3UserEntry 3 } snmpV3UserAuthProtocol OBJECT-TYPE SYNTAX INTEGER { none (1), md5 (2), sha (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type of authentication protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of UserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoAuthProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoAuthProtocol, then an 'inconsistentValue' error must be returned. If a set operation tries to set the value to the NoAuthProtocol while the UserPrivProtocol value in the same row is not equal to NoPrivProtocol, then an 'inconsistentValue' error must be returned. That means that an SNMP command generator application must first ensure that the UserPrivProtocol is set to the NoPrivProtocol value before it can set the UserAuthProtocol value to NoAuthProtocol. " ::= { snmpV3UserEntry 4 } snmpV3UserAuthProtocolPassword OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "" ::= { snmpV3UserEntry 5 } snmpV3UserPrivProtocol OBJECT-TYPE SYNTAX INTEGER { none (1), des (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if so, the type of privacy protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of usmUserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoPrivProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoPrivProtocol, then an 'inconsistentValue' error must be returned. Note that if any privacy protocol is used, then you must also use an authentication protocol. In other words, if usmUserPrivProtocol is set to anything else than NoPrivProtocol, then the corresponding instance of usmUserAuthProtocol cannot have a value of usmNoAuthProtocol. If it does, then an 'inconsistentValue' error must be returned. " ::= { snmpV3UserEntry 6 } snmpV3UserPrivProtocolPassword OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "" ::= { snmpV3UserEntry 7 } snmpV3UserStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the usmUserStatus column is 'notReady'. In particular, a newly created row for a user who employs authentication, cannot be made active until the corresponding usmUserCloneFrom and usmUserAuthKeyChange have been set. Further, a newly created row for a user who also employs privacy, cannot be made active until the usmUserPrivKeyChange has been set. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified, except for usmUserOwnAuthKeyChange and usmUserOwnPrivKeyChange. For these 2 objects, the value of usmUserStatus MUST be active. " ::= { snmpV3UserEntry 8 } -- ---------------------------------------------------------------- -- The snmpV3Group group -- ---------------------------------------------------------------- snmpV3GroupTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpV3GroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { snmpV3Group 1 } snmpV3GroupEntry OBJECT-TYPE SYNTAX SnmpV3GroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { snmpV3GroupName ,snmpV3GroupSecurityModel ,snmpV3GroupSecurityLevel} ::= { snmpV3GroupTable 1 } SnmpV3GroupEntry ::= SEQUENCE { snmpV3GroupName SnmpAdminString, snmpV3GroupSecurityModel INTEGER, snmpV3GroupSecurityLevel SnmpSecurityLevel, snmpV3GroupReadViewName SnmpAdminString, snmpV3GroupWriteViewName SnmpAdminString, snmpV3GroupNotifyViewName SnmpAdminString, snmpV3GroupStatus RowStatus } snmpV3GroupName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable. " ::= { snmpV3GroupEntry 1 } snmpV3GroupSecurityModel OBJECT-TYPE SYNTAX INTEGER { v1 (1), v2c (2), v3 (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "In order to gain the access rights allowed by this conceptual row, this securityModel must be in use. " ::= { snmpV3GroupEntry 2 } snmpV3GroupSecurityLevel OBJECT-TYPE SYNTAX SnmpSecurityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPriv which in turn is less than authPriv. If multiple entries are equally indexed except for this vacmAccessSecurityLevel index, then the entry which has the highest value for vacmAccessSecurityLevel is selected. " ::= { snmpV3GroupEntry 3 } snmpV3GroupReadViewName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted. " -- DEFVAL { ''H } -- -- the empty string -- ::= { snmpV3GroupEntry 4 } snmpV3GroupWriteViewName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted. " -- DEFVAL { ''H } -- -- the empty string -- ::= { snmpV3GroupEntry 5 } snmpV3GroupNotifyViewName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted. " -- DEFVAL { ''H } -- -- the empty string -- ::= { snmpV3GroupEntry 6 } snmpV3GroupStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified. " ::= { snmpV3GroupEntry 7 } -- ---------------------------------------------------------------- -- The snmpV3ViewTree group -- ---------------------------------------------------------------- snmpV3ViewTreeTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpV3ViewTreeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { snmpV3ViewTree 1 } snmpV3ViewTreeEntry OBJECT-TYPE SYNTAX SnmpV3ViewTreeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { snmpV3viewTreeName ,snmpV3viewTreeSubtree } ::= { snmpV3ViewTreeTable 1 } SnmpV3ViewTreeEntry ::= SEQUENCE { snmpV3viewTreeName SnmpAdminString, snmpV3viewTreeSubtree OBJECT IDENTIFIER, snmpV3viewTreeMask OCTET STRING, snmpV3viewTreeType INTEGER, snmpV3viewTreeStatus RowStatus } snmpV3viewTreeName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The human readable name for a family of view subtrees. " ::= { snmpV3ViewTreeEntry 1 } snmpV3viewTreeSubtree OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "The MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees. " ::= { snmpV3ViewTreeEntry 2 } snmpV3viewTreeMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask corresponds to a sub-identifier of vacmViewTreeFamilySubtree, with the most significant bit of the i-th octet of this octet string value (extended if necessary, see below) corresponding to the (8*i - 7)-th sub-identifier, and the least significant bit of the i-th octet of this octet string corresponding to the (8*i)-th sub-identifier, where i is in the range 1 through 16. Each bit of this bit mask specifies whether or not the corresponding sub-identifiers must match when determining if an OBJECT IDENTIFIER is in this family of view subtrees; a '1' indicates that an exact match must occur; a '0' indicates 'wild card', i.e., any sub-identifier value matches. Thus, the OBJECT IDENTIFIER X of an object instance is contained in a family of view subtrees if, for each sub-identifier of the value of vacmViewTreeFamilySubtree, either: the i-th bit of vacmViewTreeFamilyMask is 0, or the i-th sub-identifier of X is equal to the i-th sub-identifier of the value of vacmViewTreeFamilySubtree. If the value of this bit mask is M bits long and there are more than M sub-identifiers in the corresponding instance of vacmViewTreeFamilySubtree, then the bit mask is extended with 1's to be the required length. Note that when the value of this object is the zero-length string, this extension rule results in a mask of all-1's being used (i.e., no 'wild card'), and the family of view subtrees is the one view subtree uniquely identified by the corresponding instance of vacmViewTreeFamilySubtree. Note that masks of length greater than zero length do not need to be supported. In this case this object is made read-only. " -- DEFVAL { ''H } ::= { snmpV3ViewTreeEntry 3 } snmpV3viewTreeType OBJECT-TYPE SYNTAX INTEGER { included(1), excluded(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or excluded from the MIB view. " -- DEFVAL { included } ::= { snmpV3ViewTreeEntry 4 } snmpV3viewTreeStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified. " ::= { snmpV3ViewTreeEntry 5 } -- ---------------------------------------------------------------- -- The snmpV3Community group -- ---------------------------------------------------------------- snmpV3CommunityTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpV3CommunityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { snmpV3Community 1 } snmpV3CommunityEntry OBJECT-TYPE SYNTAX SnmpV3CommunityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { snmpV3CommunityName } ::= { snmpV3CommunityTable 1 } SnmpV3CommunityEntry ::= SEQUENCE { snmpV3CommunityName OCTET STRING, snmpV3CommunityPolicy SnmpAdminString, snmpV3CommunityStatus RowStatus } snmpV3CommunityName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The unique index value of a row in this table." ::= { snmpV3CommunityEntry 1 } snmpV3CommunityPolicy OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "A human readable string representing the corresponding value of snmpCommunityName in a Security Model independent format." ::= { snmpV3CommunityEntry 2 } snmpV3CommunityStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The snmpCommunityName and snmpCommunitySecurityName objects must be explicitly set. There is no restriction on setting columns in this table when the value of snmpCommunityStatus is active(1)." ::= { snmpV3CommunityEntry 3 } -- ---------------------------------------------------------------- -- The snmpV3Host group -- ---------------------------------------------------------------- snmpV3HostTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpV3HostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { snmpV3Host 2 } snmpV3HostEntry OBJECT-TYPE SYNTAX SnmpV3HostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { snmpV3HostAddress, snmpV3IPType } ::= { snmpV3HostTable 1 } SnmpV3HostEntry ::= SEQUENCE { snmpV3HostAddress Ipv6Address, snmpV3IPType INTEGER, snmpV3HostCommunityName SnmpAdminString, snmpV3HostVersion INTEGER, snmpV3HostInterfaceName OCTET STRING, snmpV3HostStatus RowStatus } snmpV3HostAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry." ::= { snmpV3HostEntry 1 } snmpV3IPType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of IP interface." ::= { snmpV3HostEntry 2 } snmpV3HostCommunityName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The locally arbitrary." ::= { snmpV3HostEntry 3 } snmpV3HostVersion OBJECT-TYPE SYNTAX INTEGER { v1 (1), v2c (2), v3NoAuthNoPriv (3), v3AuthNoPriv (4), v3AuthPriv (5) } MAX-ACCESS read-create STATUS current DESCRIPTION "The Level of Security to be used when generating SNMP messages using this entry." ::= { snmpV3HostEntry 4 } snmpV3HostInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the interface name when the syslogSrvIP is linklocal address." ::= { snmpV3HostEntry 5 } snmpV3HostStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "" ::= { snmpV3HostEntry 6 } -- ---------------------------------------------------------------- -- The snmpV3Trap group -- ---------------------------------------------------------------- snmpV3TrapSNMPAuthentication OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling SNMP login fail event trap in the system." ::= { snmpV3Trap 1 } snmpV3TrapBootup OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling devie Bootup event trap in the system." ::= { snmpV3Trap 2 } snmpV3TrapPortLinkUpDown OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling Port link up / link down event trap in the system." ::= { snmpV3Trap 3 } snmpV3TrapRSTPStateChange OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling RSTP topology change event trap in the system." ::= { snmpV3Trap 4 } snmpV3TrapFirmUpgrade OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling Firmware upgrade suess or fail event trap in the system." ::= { snmpV3Trap 5 } snmpV3TrapPoePowerOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling PoE power on /off event in the system." ::= { snmpV3Trap 6 } snmpV3TrapPoePowerError OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling PoE power error event in the system. There are four(short circuit, over load, power denied, and thermal shutdown) error types in this event." ::= { snmpV3Trap 7 } snmpV3TrapOverMaxPowerBudget OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling PoE over max power budget event in the system." ::= { snmpV3Trap 8 } snmpV3TrapLBD OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "" ::= { snmpV3Trap 11 } traps OBJECT IDENTIFIER ::= { companyTraps 0 } topologyChange NOTIFICATION-TYPE OBJECTS { ifIndex } STATUS current DESCRIPTION "AST_TOPOLOGY_CHG_TRAP_VAL." ::= { traps 4 } firmwareUpgradeSuccess NOTIFICATION-TYPE STATUS current DESCRIPTION "SNMP_FIRMUPGRADE_SUCC." ::= { traps 8 } firmwareUpgradeFailure NOTIFICATION-TYPE STATUS current DESCRIPTION "SNMP_FIRMUPGRADE_FAIL." ::= { traps 9 } firmwareIllegalFile NOTIFICATION-TYPE STATUS current DESCRIPTION "SNMP_FIRMUPGRADE_FAIL2." ::= { traps 10 } firmwareTransferError NOTIFICATION-TYPE STATUS current DESCRIPTION "SNMP_FIRMUPGRADE_FAIL1." ::= { traps 11 } firmwareChecksumError NOTIFICATION-TYPE STATUS current DESCRIPTION "SNMP_FIRMUPGRADE_FAIL3." ::= { traps 12 } poePowerOn NOTIFICATION-TYPE STATUS current DESCRIPTION "PoE Power On." ::= { traps 13 } poePowerOff NOTIFICATION-TYPE STATUS current DESCRIPTION "PoE Power Off." ::= { traps 14 } poeShortCircuit NOTIFICATION-TYPE STATUS current DESCRIPTION "PoE Power Short Circuit." ::= { traps 15 } poeOverLoad NOTIFICATION-TYPE STATUS current DESCRIPTION "PoE Power Over Load." ::= { traps 16 } poePowerDenied NOTIFICATION-TYPE STATUS current DESCRIPTION "PoE Power Denied." ::= { traps 17 } poeThermalShutdown NOTIFICATION-TYPE STATUS current DESCRIPTION "PoE Thermal Shutdown." ::= { traps 18 } poeOverMaxPowerBudget NOTIFICATION-TYPE STATUS current DESCRIPTION "PoE Over Max Power Budget." ::= { traps 19 } -- ------------------------------------------------------------------ -- companySyslog -- ------------------------------------------------------------------ syslogGeneralGroup OBJECT IDENTIFIER ::= { companySyslog 2 } -- syslogGeneralGroup syslogState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling syslog alert features in the system. System Logs record and manage events, as well as report errors and informational messages." DEFVAL { disable } ::= { syslogGeneralGroup 1 } syslogTimeStampOption OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling timestamp option. When enabled, the messages (log and email alert messages) will hold the time stamp information. When disabled, the time stamp information will not be carried with the messages sent to the log and mail servers." DEFVAL { enable } ::= { syslogGeneralGroup 2 } syslogSrvSeverity OBJECT-TYPE SYNTAX INTEGER{ warning(4), -- For logging warning messages. info(6), -- For logging informational messages. all(7) -- For logging debug messages. } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the log level option to be set for a specific module." ::= { syslogGeneralGroup 3 } syslogSrvFacility OBJECT-TYPE SYNTAX INTEGER { local0(128), -- Reserved local use local1(136), -- Reserved local use local2(144), -- Reserved local use local3(152), -- Reserved local use local4(160), -- Reserved local use local5(168), -- Reserved local use local6(176), -- Reserved local use local7(184) -- Reserved local use } MAX-ACCESS read-write STATUS current DESCRIPTION "The Syslog standard facilities. The facility to be used when sending Syslog messages to this server." ::= { syslogGeneralGroup 4 } -- syslogSrvTable -- This table is for configuring the Logging server forward table syslogSrvTable OBJECT-TYPE SYNTAX SEQUENCE OF SyslogSrvEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing entries of priority,server address type, server address, port through which it can send and tranport type." ::= { syslogGeneralGroup 5 } syslogSrvEntry OBJECT-TYPE SYNTAX SyslogSrvEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing index as priority , server address type and server address." INDEX { syslogSrvIPType, syslogSrvIP} ::= { syslogSrvTable 1 } SyslogSrvEntry::= SEQUENCE { syslogSrvIPType INTEGER, syslogSrvIP Ipv6Address, syslogSrvPort Integer32, syslogInterfaceName OCTET STRING, syslogSrvRowStatus RowStatus } syslogSrvIPType OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the Address type of server.Address type shall be ipv4 or ipv6." ::= { syslogSrvEntry 1 } syslogSrvIP OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the ServerIP to which the syslog shall be forwarded." ::= { syslogSrvEntry 2 } syslogSrvPort OBJECT-TYPE SYNTAX Integer32(0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the Port through which it can send the syslog message. By default the the port is 514" DEFVAL { 514 } ::= { syslogSrvEntry 3 } syslogInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the interface name when the syslogSrvIP is linklocal address." ::= { syslogSrvEntry 4 } syslogSrvRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The Status of the Server Entry." ::= { syslogSrvEntry 5 } --Table ends -- LBD Group ------------------------------------------------------ sysLBDStateEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Loopback detection function. The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree Protocol (STP) is not enabled in the network, especially when the down links are hubs or unmanaged switchs.The Switch will automatically shutdown the port and sends a log to the administrator." DEFVAL { disabled } ::= { companyLBD 1 } sysLBDMode OBJECT-TYPE SYNTAX INTEGER { port(1), vlan(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Loopback detection function mode." DEFVAL { port } ::= { companyLBD 2 } sysLBDInterval OBJECT-TYPE SYNTAX Integer32 (1..32767) MAX-ACCESS read-write STATUS current DESCRIPTION "Set a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds. This time interval to be used at counting time seconds to resend the CTP packet automatically." DEFVAL { 2 } ::= { companyLBD 3 } sysLBDRecoverTime OBJECT-TYPE SYNTAX Integer32 (0 | 60..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This time interval to be used at counting time seconds to recover the disabled port automatically. The Loop Detection Recover Time can be set at 0 seconds, or 60 to 1000000 seconds. Entering 0 will disable the Loop Detection Recover Time. The default is 60 seconds." DEFVAL { 60 } ::= { companyLBD 4 } -- LBD Port Control Table sysLBDCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF SysLBDCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control Loopback detection features either for the entire switch or for each interface in the switch." ::= { companyLBD 5 } sysLBDCtrlEntry OBJECT-TYPE SYNTAX SysLBDCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system." INDEX { sysLBDCtrlIndex } ::= { sysLBDCtrlTable 1 } SysLBDCtrlEntry ::= SEQUENCE { sysLBDCtrlIndex Integer32, sysLBDPortStatus INTEGER, sysLBDPortLoopStatus INTEGER } sysLBDCtrlIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index of the port for which the configuration in this entry applies." ::= { sysLBDCtrlEntry 1 } sysLBDPortStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Provides control to per port enable or disable the loopback detection function. Default is disabled." DEFVAL { disabled } ::= { sysLBDCtrlEntry 2 } sysLBDPortLoopStatus OBJECT-TYPE SYNTAX INTEGER { normal(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The loop status for this port." ::= { sysLBDCtrlEntry 3 } -- LBD Vlan Loop Table sysLBDVlanLoopTable OBJECT-TYPE SYNTAX SEQUENCE OF SysLBDVlanLoopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to display Loopback detection features by vlan mode ." ::= { companyLBD 6 } sysLBDVlanLoopEntry OBJECT-TYPE SYNTAX SysLBDVlanLoopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system." INDEX { sysLBDVlanLoopIndex } ::= { sysLBDVlanLoopTable 1 } SysLBDVlanLoopEntry ::= SEQUENCE { sysLBDVlanLoopIndex Integer32, sysLBDVlanLoopPorts PortList } sysLBDVlanLoopIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display port lists loop status by vlan." ::= { sysLBDVlanLoopEntry 1 } sysLBDVlanLoopPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "Display port lists loop status by vlan." ::= { sysLBDVlanLoopEntry 2 } --For CAMEO_DLINK_LBD_VERSION_4_0_5 swLoopDetectEnabledVlanList OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the VLANs that enabled LBD. Note: For the LBD enabled VLAN specification, the value should be separated by ',' or '-'. Such as: 1,4,7 or 1,4,7-9 ." ::= { companyLBD 7 } -- ------------------------------------------------------------------ -- Mirror Group -- ------------------------------------------------------------------ sysMirrorStatus OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Port Mirroring function. Default is disabled. Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another port where the packet can be studied." -- "Provides control over the mirroring feature in the switch." -- DEFVAL { disabled } ::= { companyMirror 1 } sysMirrorTargetPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the port to which the mirrored traffic in the system is to be copied." ::= { companyMirror 2 } sysMirrorCtrlIngressMirroring OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port." ::= { companyMirror 3 } sysMirrorCtrlEgressMirroring OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port." ::= { companyMirror 4 } -- ------------------------------------------------------------------ -- SNTP Timesetting -- ------------------------------------------------------------------ --IPv6 sntp server Table sysSNTPServerTable OBJECT IDENTIFIER ::= { companySNTPSetting 17 } sysSNTPTimeSeconds OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UTC, January 1, 2009) and smaller than 2145916799 (23:59:59 UTC, December 31, 2037)." ::= { sysSNTPServerTable 1 } sysSNTPFirstServer OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP First Server's IPv6 Address" ::= { sysSNTPServerTable 2 } sysSNTPFirstType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP First Server's IPv6 Address type." ::= { sysSNTPServerTable 3 } sysSNTPFirstInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the interface name when the sysSNTPFirstServer is linklocal address." ::= { sysSNTPServerTable 4 } sysSNTPSecondServer OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP Second Server's IPv6 Address" ::= { sysSNTPServerTable 5 } sysSNTPSecondType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP First Server's IPv6 Address type." ::= { sysSNTPServerTable 6 } sysSNTPSecondInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the interface name when the sysSNTPSecondServer is linklocal address." ::= { sysSNTPServerTable 7 } sysSNTPPollInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP Poll Interval In Seconds (30-99999) " ::= { sysSNTPServerTable 8 } sysSNTPState OBJECT-TYPE SYNTAX INTEGER { sntp(1), local(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable SNTP function in the system." ::= { sysSNTPServerTable 9 } -- SNTPv6 TimeZonesetting sysSNTPDSTOffset OBJECT-TYPE SYNTAX INTEGER { offset30min (30), offset60min (60), offset90min (90), offset120min (120) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes." ::= { sysSNTPServerTable 10 } sysSNTPGMTMinutes OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)" ::= { sysSNTPServerTable 11 } sysSNTPDSTStartMon OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The start month of Daylight Saving Time." ::= { sysSNTPServerTable 12 } sysSNTPDSTStartDay OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The start day of Daylight Saving Time." ::= { sysSNTPServerTable 13 } sysSNTPDSTStartHour OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The start hour of Daylight Saving Time." ::= { sysSNTPServerTable 14 } sysSNTPDSTStartMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The start minute of Daylight Saving Time." ::= { sysSNTPServerTable 15 } sysSNTPDSTEndMon OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The end month of Daylight Saving Time." ::= { sysSNTPServerTable 16 } sysSNTPDSTEndDay OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The end day of Daylight Saving Time." ::= { sysSNTPServerTable 17 } sysSNTPDSTEndHour OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The end hour of Daylight Saving Time." ::= { sysSNTPServerTable 18 } sysSNTPDSTEndMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The end minute of Daylight Saving Time." ::= { sysSNTPServerTable 19 } sysSNTPDSTState OBJECT-TYPE SYNTAX INTEGER { annual(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for Annual(1) or Disabled(2) DST state in the system." ::= { sysSNTPServerTable 20 } -- --------------------------------------------------------------------- -- voicevlan Function -- --------------------------------------------------------------------- voicevlanSystem OBJECT IDENTIFIER ::= { companyVoiceVlan 1 } voicevlanOUI OBJECT IDENTIFIER ::= { companyVoiceVlan 2 } voicevlanDevice OBJECT IDENTIFIER ::= { companyVoiceVlan 3 } -- ------------------------------------------------------------------ -- The Voice Vlan Group -- ------------------------------------------------------------------ voiceVlanMode OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Voice VLAN is a feature that allows you to automatically place the voice traffic from IP phone to an assigned VLAN to enhance the VoIP service. This object is for enabling or disabling Voice Vlan function in the system. If the Vlan mode is in Asymmetric VLAN mode, Voice VLAN can not be enabled." ::= { voicevlanSystem 2 } voiceVlanId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The ID of VLAN that you want the voice traffic to be in. It must be a exist vlan id." ::= { voicevlanSystem 3 } voiceVlanTimeout OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "A period of time in hour to remove a port from voice VLAN if the port is an automatic VLAN member. The Timeout range is 1~120 hours. Default aging time is 1 hour." ::= { voicevlanSystem 4} voiceVlanPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The 802.1p priority levels of the traffic in the Voice VLAN." ::= { voicevlanSystem 5} -- -- Voice Vlan Port Control Table -- voicevlanPortControlTable OBJECT-TYPE SYNTAX SEQUENCE OF VoiceVlanPortControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains Voice Vlan Port Control configuration information." ::= { voicevlanSystem 6 } voicevlanPortControlEntry OBJECT-TYPE SYNTAX VoiceVlanPortControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Voice Vlan Control configuration parameters for each Port on this device." INDEX { voicevlanPortControlIndex } ::= { voicevlanPortControlTable 1 } VoiceVlanPortControlEntry ::= SEQUENCE { voicevlanPortControlIndex InterfaceIndex, voicevlanPortAutoDetection INTEGER, voicevlanPortManuTagMode INTEGER, voicevlanPortCurrentTagMode INTEGER, voicevlanPortState INTEGER } voicevlanPortControlIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The voice vlan port index." ::= { voicevlanPortControlEntry 1 } voicevlanPortAutoDetection OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling Voice Vlan Auto Detection in the port. If the auto detection is enable, switch will add this port to the voice VLAN automatically if it detects the device OUI matches the Telephony OUI. If the port is a static member of voice vlan or a LA member, it can not enable voice vlan auto detection." ::= { voicevlanPortControlEntry 2 } voicevlanPortManuTagMode OBJECT-TYPE SYNTAX INTEGER { tag(1), untag(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "User assign per port tag/untag mode." ::= { voicevlanPortControlEntry 3 } voicevlanPortCurrentTagMode OBJECT-TYPE SYNTAX INTEGER { tag(1), untag(2), none(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Per port current tag/untag mode." ::= { voicevlanPortControlEntry 4 } voicevlanPortState OBJECT-TYPE SYNTAX INTEGER { manual(1), dynamic(2), none(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates Voice vlan state to this Port. manual - this port is a static member of voice vlan. dynamic - this port is a dynamic member of voice vlan. none - this port is not a member of voice vlan." ::= { voicevlanPortControlEntry 5 } -- ------------------------------------------------------------------ -- The Voice Vlan OUI Group -- ------------------------------------------------------------------ -- -- Voice Vlan OUI Table -- voicevlanOUITable OBJECT-TYPE SYNTAX SEQUENCE OF VoicevlanOUIEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A voice vlan OUI entry containing the description and mac." ::= { voicevlanOUI 1 } voicevlanOUIEntry OBJECT-TYPE SYNTAX VoicevlanOUIEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A voice vlan OUI entry containing the description and mac." INDEX { voicevlanOUITelephonyOUI } ::= { voicevlanOUITable 1 } VoicevlanOUIEntry ::= SEQUENCE { voicevlanOUITelephonyOUI MacAddress, voicevlanOUIDescription OCTET STRING, voicevlanOUIMask MacAddress, voicevlanOUIStatus RowStatus } voicevlanOUITelephonyOUI OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object indicates the voice traffic's OUI that user created." ::= { voicevlanOUIEntry 1 } voicevlanOUIDescription OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The Description for the OUI." ::= { voicevlanOUIEntry 2 } voicevlanOUIMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Voice vlan OUI Mask. Always be FF:FF:FF:00:00:00." ::= { voicevlanOUIEntry 3 } voicevlanOUIStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of this entry. To create a new entry, you must set the voicevlanOUIStatus to be CreateAndGo, then this entry will turn to be Active." ::= { voicevlanOUIEntry 4 } -- ------------------------------------------------------------------ -- The Voice Vlan Device Group -- ------------------------------------------------------------------ -- -- Voice Vlan Device Table -- voicevlanDeviceTable OBJECT-TYPE SYNTAX SEQUENCE OF VoicevlanDeviceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A voice vlan Device entry containing the description and mac." ::= { voicevlanDevice 1 } voicevlanDeviceEntry OBJECT-TYPE SYNTAX VoicevlanDeviceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A voice vlan Device entry containing the description and mac." INDEX { voicevlanDeviceIndexMac } ::= { voicevlanDeviceTable 1 } VoicevlanDeviceEntry ::= SEQUENCE { voicevlanDeviceIndexMac MacAddress, voicevlanDevicePort INTEGER, voicevlanDevicePriority INTEGER, voicevlanDeviceTagType INTEGER, voicevlanDeviceStatus INTEGER } voicevlanDeviceIndexMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Mac Address is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object indicates the voice traffic's Mac that voice device created." ::= { voicevlanDeviceEntry 1 } voicevlanDevicePort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The port is learning by voice device." ::= { voicevlanDeviceEntry 2 } voicevlanDevicePriority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The priority value for voice device." ::= { voicevlanDeviceEntry 3 } voicevlanDeviceTagType OBJECT-TYPE SYNTAX INTEGER { tag(1), untag(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The tag type for voice device." ::= { voicevlanDeviceEntry 4 } voicevlanDeviceStatus OBJECT-TYPE SYNTAX INTEGER { active(1), destroy(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of this entry. You can delete this object." ::= { voicevlanDeviceEntry 5 } -- --------------------------------------------------------------------- -- Auto Surveillance Vlan Function -- --------------------------------------------------------------------- autoSurveillanceVlanSystem OBJECT IDENTIFIER ::= { companyAutoSurveillanceVlan 1 } autoSurveillanceVlanOUI OBJECT IDENTIFIER ::= { companyAutoSurveillanceVlan 2 } -- ------------------------------------------------------------------ -- The Auto Surveillance Vlan Group -- ------------------------------------------------------------------ autoSurveillanceVlanMode OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling Auto Surveillance Vlan function in the system. If the Vlan mode is in Asymmetric VLAN mode, Auto Surveillance VLAN can not be enabled." ::= { autoSurveillanceVlanSystem 1 } autoSurveillanceVlanId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The ID of VLAN that you want the surveillance traffic to be in. It must be a exist vlan id." ::= { autoSurveillanceVlanSystem 2 } autoSurveillanceVlanPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The 802.1p priority levels of the traffic in the Auto Surveillance VLAN." ::= { autoSurveillanceVlanSystem 3} autoSurveillanceVlanTaggedUplinkDownlinkPort OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Auto Surveillance vlan uplink ports can't auto learning OUI." ::= { autoSurveillanceVlanSystem 4 } -- ------------------------------------------------------------------ -- The Auto Surveillance Vlan OUI Group -- ------------------------------------------------------------------ -- -- Auto Surveillance Vlan OUI Table -- autoSurveillanceVlanOUITable OBJECT-TYPE SYNTAX SEQUENCE OF AutoSurveillanceVlanOUIEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Auto Surveillance vlan OUI entry containing the description and mac." ::= { autoSurveillanceVlanOUI 1 } autoSurveillanceVlanOUIEntry OBJECT-TYPE SYNTAX AutoSurveillanceVlanOUIEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Auto Surveillance vlan OUI entry containing the description and mac." INDEX { autoSurveillanceVlanOUISurveillanceOUI } ::= { autoSurveillanceVlanOUITable 1 } AutoSurveillanceVlanOUIEntry ::= SEQUENCE { autoSurveillanceVlanOUISurveillanceOUI MacAddress, autoSurveillanceVlanOUIDescription OCTET STRING, autoSurveillanceVlanOUIMask MacAddress, autoSurveillanceVlanOUIStatus RowStatus, autoSurveillanceVlanOUIComponentType INTEGER } autoSurveillanceVlanOUISurveillanceOUI OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object indicates the surveillance traffic's OUI that user created." ::= { autoSurveillanceVlanOUIEntry 1 } autoSurveillanceVlanOUIDescription OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The Description for the OUI." ::= { autoSurveillanceVlanOUIEntry 2 } autoSurveillanceVlanOUIMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Auto Surveillance vlan OUI Mask. The default OUI Mask is FF:FF:FF:F0:00:00. And default OUI Mask is read-only. In user define OUI's Mask is FF:FF:FF:00:00:00, in user define MAC's Mask is FF:FF:FF:FF:FF:FF." ::= { autoSurveillanceVlanOUIEntry 3 } autoSurveillanceVlanOUIComponentType OBJECT-TYPE SYNTAX INTEGER { video_Management_Server(0), vMS_Client(1), video_Encoder(2), network_Storage(3), other_IP_Surveillance_Devices(4), d-Link_Surveillance_Device(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the Component Type of this entry. To create a new entry, you must set the autoSurveillanceVlanOUIComponentType to be CreateAndGo, then this entry will turn to be Active." ::= { autoSurveillanceVlanOUIEntry 4 } autoSurveillanceVlanOUIStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of this entry. To create a new entry, you must set the autoSurveillanceVlanOUIStatus to be CreateAndGo, then this entry will turn to be Active." ::= { autoSurveillanceVlanOUIEntry 5 } -- ----------------------------------------------------------------- -- The PoE Groups -- ----------------------------------------------------------------- -------------------------------------------- -- PoEPortSetting -------------------------------------------- sysPoEPortSettingTable OBJECT-TYPE SYNTAX SEQUENCE OF SysPoEPortSettingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects that display and control the power characteristics of power Ethernet ports on a Power Source Entity (PSE) device." ::= { companyPoEGroup 1 } sysPoEPortSettingEntry OBJECT-TYPE SYNTAX SysPoEPortSettingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of objects that display and control the power characteristics of a power Ethernet PSE port." INDEX { poeportgroup, poeportid } ::= { sysPoEPortSettingTable 1 } SysPoEPortSettingEntry ::= SEQUENCE { poeportgroup INTEGER, poeportid INTEGER, poePortSettingState INTEGER, poePortTimeBaseSchduleID Integer32, poePortSettingPriority INTEGER, poePortSettingPowerLimit INTEGER, poePortSettingUserDefineState INTEGER, poePortSettingUserDefine DisplayString, poePortPower DisplayString, poePortVoltage DisplayString, poePortCurrent DisplayString, poePortClassification DisplayString, poePortDelayPowerDetect INTEGER, poePortLegacyPDDetect INTEGER, poePortStatus DisplayString } poeportgroup OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object is the PoE port group index." ::= { sysPoEPortSettingEntry 1 } poeportid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object is the PoE Port ID Index." ::= { sysPoEPortSettingEntry 2 } poePortSettingState OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable PoE function on this port." ::= { sysPoEPortSettingEntry 3 } poePortTimeBaseSchduleID OBJECT-TYPE SYNTAX Integer32 (0..8) MAX-ACCESS read-write STATUS current DESCRIPTION "Enable timebase schedule function and join with this schedule ID on this port. Setting 0 means disable timebase schedule function on this port." ::= { sysPoEPortSettingEntry 4 } poePortSettingPriority OBJECT-TYPE SYNTAX INTEGER { low (1), normal (2), high (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures PoE port priority." ::= { sysPoEPortSettingEntry 5 } poePortSettingPowerLimit OBJECT-TYPE SYNTAX INTEGER { auto (1), class1 (2), class2 (3), class3 (4), class4 (5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures PoE port power limit." ::= { sysPoEPortSettingEntry 6 } poePortSettingUserDefineState OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable manual configuring max power on this port." ::= { sysPoEPortSettingEntry 7 } poePortSettingUserDefine OBJECT-TYPE SYNTAX DisplayString (SIZE(1..4)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object manually configures max power value(e.g., `1, 2.2, 21.8') on this port. The per-port power limit must be a multiple of 0.2. If the user define state is not enabled, the value is the zero-length string." --DEFVAL { 0 } ::= { sysPoEPortSettingEntry 8 } poePortPower OBJECT-TYPE SYNTAX DisplayString (SIZE(1..4)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays PoE port power(W)(e.g., `0.0, 2.3, 21.8'). If the PoE port tatus is POWER OFF, the value is 0.0." --DEFVAL { 0 } ::= { sysPoEPortSettingEntry 9 } poePortVoltage OBJECT-TYPE SYNTAX DisplayString (SIZE(1..4)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays PoE port voltage(V)(e.g., `0.0, 2.3, 21.8'). If the PoE port tatus is POWER OFF, the value is 0.0." --DEFVAL { 0 } ::= { sysPoEPortSettingEntry 10 } poePortCurrent OBJECT-TYPE SYNTAX DisplayString (SIZE(1..5)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays PoE port current(mA)(e.g., `0.0, 22.3, 120.8'). If the PoE port tatus is POWER OFF, the value is 0.0." --DEFVAL { 0 } ::= { sysPoEPortSettingEntry 11 } poePortClassification OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays PoE port power classification(e.g., `NA, Class 2, 20.2(User Defined)'). If the PoE port tatus is POWER OFF, the value is NA." --DEFVAL { 0 } ::= { sysPoEPortSettingEntry 12 } poePortDelayPowerDetect OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Delay Power Detect function on this port." ::= { sysPoEPortSettingEntry 13} poePortLegacyPDDetect OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Legacy PD Detect function on this port." ::= { sysPoEPortSettingEntry 14} poePortStatus OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays PoE port powering status(e.g., `POWER OFF, POWER ON')." --DEFVAL { 0 } ::= { sysPoEPortSettingEntry 99 } -------------------------------------------- -- PoESystemSetting -------------------------------------------- poeSystemSettingPowerThreshold OBJECT-TYPE SYNTAX DisplayString (SIZE(1..4)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures available system power budget (e.g., `50.2')." --DEFVAL { 0 } ::= { companyPoEGroup 2 } poeSystemSettingDisconnectMethod OBJECT-TYPE SYNTAX INTEGER { denyNextPort (1), denyLowPriorityPort (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures PoE power denied rule while system entering in guard band mode." ::= { companyPoEGroup 3 } pethPsePortPowerBudget OBJECT-TYPE SYNTAX DisplayString (SIZE(1..4)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays PoE system power budget (e.g., `50.2')." --DEFVAL { 0 } ::= { companyPoEGroup 4 } pethPsePortPowerConsumption OBJECT-TYPE SYNTAX DisplayString (SIZE(1..4)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays PoE total power consumption (e.g., `3.3, 15.4')." --DEFVAL { 0 } ::= { companyPoEGroup 5 } pethPsePortPowerRemainder OBJECT-TYPE SYNTAX DisplayString (SIZE(1..4)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays PoE power remainder (e.g., `60.2')." --DEFVAL { 0 } ::= { companyPoEGroup 6 } pethPsePortPowerRatioOfSystemPower OBJECT-TYPE SYNTAX DisplayString (SIZE(1..4)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays power ratio of system power in unit of percentage(e.g., `4.2')." --DEFVAL { 0 } ::= { companyPoEGroup 7 } poeLedMode OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Port led mode indicator. 1: Link/Act/Speed mode; 2: PoE mode." ::= { companyPoEGroup 8 } -- ------------------------------------------------------------------ -- The Time Range Setting -- ------------------------------------------------------------------ swTimeRangeSettingTable OBJECT-TYPE SYNTAX SEQUENCE OF SwTimeRangeSettingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to configure time Range in the system." ::= { companyTimeRangeMgmt 1 } swTimeRangeSettingEntry OBJECT-TYPE SYNTAX SwTimeRangeSettingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A schedule entry to configure time Range in the system." INDEX { swTimeRangeIndex } ::= { swTimeRangeSettingTable 1 } SwTimeRangeSettingEntry ::= SEQUENCE { swTimeRangeIndex Integer32, swTimeRangeName DisplayString, swTimeRangeDate INTEGER, swTimeRangeStartYear INTEGER, swTimeRangeStartMonth INTEGER, swTimeRangeStartDay Integer32, swTimeRangeStartHour Integer32, swTimeRangeStartMinute Integer32, swTimeRangeEndYear INTEGER, swTimeRangeEndMonth INTEGER, swTimeRangeEndDay Integer32, swTimeRangeEndHour Integer32, swTimeRangeEndMinute Integer32, swTimeRangeMonday INTEGER, swTimeRangeTuesday INTEGER, swTimeRangeWednesday INTEGER, swTimeRangeThursday INTEGER, swTimeRangeFriday INTEGER, swTimeRangeSaturday INTEGER, swTimeRangeSunday INTEGER, swTimeRangeRowStatus RowStatus } swTimeRangeIndex OBJECT-TYPE SYNTAX Integer32 (1..52) MAX-ACCESS read-only STATUS current DESCRIPTION "The Time Range identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 52." ::= { swTimeRangeSettingEntry 1 } swTimeRangeName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Schedule name associated with the Schedule entry (e.g., `abc, bbb')." ::= { swTimeRangeSettingEntry 2} swTimeRangeDate OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable date range checking while executing time base PoE." ::= { swTimeRangeSettingEntry 3} swTimeRangeStartYear OBJECT-TYPE SYNTAX INTEGER { y2009(2009), y2010(2010), y2011(2011), y2012(2012), y2013(2013), y2014(2014), y2015(2015), y2016(2016), y2017(2017), y2018(2018), y2019(2019), y2020(2020), y2021(2021), y2022(2022), y2023(2023), y2024(2024), y2025(2025), y2026(2026), y2027(2027), y2028(2028), y2029(2029), y2030(2030), y2031(2031), y2032(2032), y2033(2033), y2034(2034), y2035(2035), y2036(2036), y2037(2037) } MAX-ACCESS read-write STATUS current DESCRIPTION "Start year of the Schedule entry." ::= { swTimeRangeSettingEntry 4 } swTimeRangeStartMonth OBJECT-TYPE SYNTAX INTEGER { january(1), february(2), march(3), april(4), may(5), june(6), july(7), august(8), september(9), october(10), november(11), december(12) } MAX-ACCESS read-write STATUS current DESCRIPTION "Start month of the Schedule entry." ::= { swTimeRangeSettingEntry 5 } swTimeRangeStartDay OBJECT-TYPE SYNTAX Integer32 (1..31) MAX-ACCESS read-write STATUS current DESCRIPTION "Start day of the Schedule entry. The value must be from 1 to 31." ::= { swTimeRangeSettingEntry 6 } swTimeRangeStartHour OBJECT-TYPE SYNTAX Integer32 (0..23) MAX-ACCESS read-write STATUS current DESCRIPTION "Start hour of the Schedule entry. The value must be from 0 to 23." ::= { swTimeRangeSettingEntry 7 } swTimeRangeStartMinute OBJECT-TYPE SYNTAX Integer32 (0..59) MAX-ACCESS read-write STATUS current DESCRIPTION "Start minute of the Schedule entry. The value must be from 0 to 59." ::= { swTimeRangeSettingEntry 8 } swTimeRangeEndYear OBJECT-TYPE SYNTAX INTEGER { y2009(2009), y2010(2010), y2011(2011), y2012(2012), y2013(2013), y2014(2014), y2015(2015), y2016(2016), y2017(2017), y2018(2018), y2019(2019), y2020(2020), y2021(2021), y2022(2022), y2023(2023), y2024(2024), y2025(2025), y2026(2026), y2027(2027), y2028(2028), y2029(2029), y2030(2030), y2031(2031), y2032(2032), y2033(2033), y2034(2034), y2035(2035), y2036(2036), y2037(2037) } MAX-ACCESS read-write STATUS current DESCRIPTION "End year of the Schedule entry." ::= { swTimeRangeSettingEntry 9 } swTimeRangeEndMonth OBJECT-TYPE SYNTAX INTEGER { january(1), february(2), march(3), april(4), may(5), june(6), july(7), august(8), september(9), october(10), november(11), december(12) } MAX-ACCESS read-write STATUS current DESCRIPTION "End month of the Schedule entry." ::= { swTimeRangeSettingEntry 10 } swTimeRangeEndDay OBJECT-TYPE SYNTAX Integer32 (1..31) MAX-ACCESS read-write STATUS current DESCRIPTION "End day of the Schedule entry. The value must be from 1 to 31." ::= { swTimeRangeSettingEntry 11 } swTimeRangeEndHour OBJECT-TYPE SYNTAX Integer32 (0..23) MAX-ACCESS read-write STATUS current DESCRIPTION "End hour of the Schedule entry. The value must be from 0 to 23." ::= { swTimeRangeSettingEntry 12 } swTimeRangeEndMinute OBJECT-TYPE SYNTAX Integer32 (0..59) MAX-ACCESS read-write STATUS current DESCRIPTION "End minute of the Schedule entry. The value must be from 0 to 59." ::= { swTimeRangeSettingEntry 13 } swTimeRangeMonday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Monday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 14 } swTimeRangeTuesday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Tuesday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 15 } swTimeRangeWednesday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Wednesday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 16 } swTimeRangeThursday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Thursday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 17 } swTimeRangeFriday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Friday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 18 } swTimeRangeSaturday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Saturday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 19 } swTimeRangeSunday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Sunday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 20 } swTimeRangeRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of an entry in the Time Range Information Table. Only a subset of the rowstatus variables (active, notinservice, createAndWait, destroy) are available." ::= { swTimeRangeSettingEntry 21 } -- -- LLDP Settings -- dlinklldpState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used for enabling or disabling LLDP in the system." DEFVAL { disable } ::= { companyLLDPSetting 1 } dlinklldpMsgHoldMultiplier OBJECT-TYPE SYNTAX INTEGER (2..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The time-to-live value expressed as a multiple of the lldpMessageTxInterval object.The actual time-to-live value used in LLDP frames, transmitted on behalf of this LLDP agent, can be expressed by the following formula: TTL = min(65535, (lldpMessageTxInterval * lldpMessageTxHoldMultiplier))" --DEFVAL { 4 } ::= { companyLLDPSetting 2 } dlinklldpMsgTxInterval OBJECT-TYPE SYNTAX INTEGER (5..32768) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used for LLDP packet update frequency. The timer in units of seconds." --DEFVAL { 30 } ::= { companyLLDPSetting 3 } dlinklldpReinitDelay OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used for LLDP Reinitialization Delay. The timer in units of seconds." --DEFVAL { 2 } ::= { companyLLDPSetting 4 } dlinklldpTxDelay OBJECT-TYPE SYNTAX INTEGER (1..8192) MAX-ACCESS read-write STATUS current DESCRIPTION "The lldpTxDelay indicates the delay (in units of seconds) between successive LLDP frame transmissions initiated by value/status changes in the LLDP local systems MIB. The recommended value for the lldpTxDelay is set by the following formula: 1 <= lldpTxDelay <= (0.25 * lldpMessageTxInterval)." --DEFVAL { 2 } ::= { companyLLDPSetting 5 } -- -- lldpManAddrConfigTxPortsTable : selection of management addresses -- to be transmitted on a specified set -- of ports. -- -- dlinklldpConfigManAddrPortsTxEnable OBJECT-TYPE -- SYNTAX PortList -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "A set of ports that are identified by a PortList, in which -- each port is represented as a bit. The corresponding local -- system management address instance will be transmitted on the -- member ports of the lldpManAddrPortsTxEnable. -- -- The default value for lldpConfigManAddrPortsTxEnable object -- is empty binary string, which means no ports are specified -- for advertising indicated management address instance." -- REFERENCE -- "IEEE 802.1AB-2005 10.2.1.1" -- ::= { companyLLDPSetting 6 } -- -- lldpManAddrConfigTxPortsTable : selection of management addresses -- to be transmitted on a specified set -- of ports. -- dlinklldpConfigManAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF DlinklldpConfigManAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table that controls selection of LLDP management address TLV instances to be transmitted on individual ports." ::= { companyLLDPSetting 7 } dlinklldpConfigManAddrEntry OBJECT-TYPE SYNTAX DlinklldpConfigManAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP configuration information that specifies the set of ports (represented as a PortList) on which the local system management address instance will be transmitted. This configuration object augments the lldpLocManAddrEntry, therefore it is only present along with the management address instance contained in the associated lldpLocManAddrEntry entry. Each active lldpConfigManAddrEntry must be restored from non-volatile and re-created (along with the corresponding lldpLocManAddrEntry) after a re-initialization of the management system." INDEX { dlinklldpLocManAddrSubtype, dlinklldpLocManAddr } ::= { dlinklldpConfigManAddrTable 1 } DlinklldpConfigManAddrEntry ::= SEQUENCE { dlinklldpLocManAddrSubtype AddressFamilyNumbers, dlinklldpLocManAddr LldpManAddress, dlinklldpConfigManAddrPortsTxEnable PortList } dlinklldpLocManAddrSubtype OBJECT-TYPE SYNTAX AddressFamilyNumbers MAX-ACCESS read-only STATUS current DESCRIPTION "The type of management address identifier encoding used in the associated 'lldpLocManagmentAddr' object." REFERENCE "IEEE 802.1AB-2005 9.5.9.3" ::= { dlinklldpConfigManAddrEntry 1 } dlinklldpLocManAddr OBJECT-TYPE SYNTAX LldpManAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The string value used to identify the management address component associated with the local system. The purpose of this address is to contact the management entity." REFERENCE "IEEE 802.1AB-2005 9.5.9.4" ::= { dlinklldpConfigManAddrEntry 2 } dlinklldpConfigManAddrPortsTxEnable OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "A set of ports that are identified by a PortList, in which each port is represented as a bit. The corresponding local system management address instance will be transmitted on the member ports of the lldpManAddrPortsTxEnable. The default value for lldpConfigManAddrPortsTxEnable object is empty binary string, which means no ports are specified for advertising indicated management address instance." REFERENCE "IEEE 802.1AB-2005 10.2.1.1" DEFVAL { ''H } ::= { dlinklldpConfigManAddrEntry 3 } -- -- LLDP-MED for PoE Port Settings -- lldpMEDPortControlTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpMEDPortControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains LLDP-MED control, A row appears in this table for each physical port." ::= { companyLLDPSetting 8 } lldpMEDPortControlEntry OBJECT-TYPE SYNTAX LldpMEDPortControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of LLDP-MED for PoE Port Settings parameters for each Port on this device." INDEX { lldpMEDPortControlIndex } ::= { lldpMEDPortControlTable 1 } LldpMEDPortControlEntry ::= SEQUENCE { lldpMEDPortControlIndex InterfaceIndex, lldpMEDPortState INTEGER } lldpMEDPortControlIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The Control Index of the LLDP-MED Power PSE TLV port." ::= { lldpMEDPortControlEntry 1 } lldpMEDPortState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling LLDP-MED Power PSE TLV Setting in the system." ::= { lldpMEDPortControlEntry 2 } -- -- LLDP for Anti-Rogue Settings -- dlinklldpAntiRoguePortControl OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "When LLDP anti-rogue port control is enabled , this identifies the port control status of each port. The default setting is disable." ::= { companyLLDPSetting 9 } dlinklldpRemOrgDefInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF DlinklldpRemOrgDefInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per physical network connection which advertises the organizationally defined information. Note that this table contains one or more rows of organizationally defined information that is not recognized by the local agent. If the local system is capable of recognizing any organizationally defined information, appropriate extension MIBs from the organization should be used for information retrieval." ::= { companyLLDPSetting 10 } dlinklldpRemOrgDefInfoEntry OBJECT-TYPE SYNTAX DlinklldpRemOrgDefInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the unrecognized organizationally defined information advertised by the remote system. The lldpAntiRoguePortIndex is index to this table." INDEX { dlinklldpAntiRoguePortIndex } ::= { dlinklldpRemOrgDefInfoTable 1 } DlinklldpRemOrgDefInfoEntry ::= SEQUENCE { dlinklldpAntiRoguePortIndex InterfaceIndex, dlinklldpAntiRoguePortStatus INTEGER, dlinklldpRemOrgDefInfoOUI OCTET STRING } dlinklldpAntiRoguePortIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The Control Index of the LLDP Anti-Rogue port." ::= { dlinklldpRemOrgDefInfoEntry 1 } dlinklldpAntiRoguePortStatus OBJECT-TYPE SYNTAX INTEGER { authenticationDisabled(0), authenticationEnabled(1), authenticationSuccessful(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value represents each port's authentication status. 0: Authentication disabled. 1: Authentication enabled but not passed. 2: Authentication successful." ::= { dlinklldpRemOrgDefInfoEntry 2 } dlinklldpRemOrgDefInfoOUI OBJECT-TYPE SYNTAX OCTET STRING (SIZE(3)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Organizationally Unique Identifier (OUI), as defined in IEEE std 802-2001, is a 24 bit (three octets) globally unique assigned number referenced by various standards, of the information received from the remote system." REFERENCE "IEEE 802.1AB-2005 9.5.1.3" ::= { dlinklldpRemOrgDefInfoEntry 3 } dlinklldpAntiRoguePassword OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used for Anti-Rogue Password setting. The default LLDP Anti-Rogue password is 'admin'." ::= { companyLLDPSetting 11 } -- --------------------------------------------------------------------- -- Green Function -- --------------------------------------------------------------------- dlinkGreenLEDShutoff OBJECT IDENTIFIER ::= { companyGreenSetting 1 } dlinkGreenPortShutoff OBJECT IDENTIFIER ::= { companyGreenSetting 2 } dlinkGreenSystemHibernation OBJECT IDENTIFIER ::= { companyGreenSetting 4 } -- --------------------------------------------------------------------- -- Green Disable LED -- --------------------------------------------------------------------- dlinkGreenLEDShutoffPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Provides control to disable LED port." ::= { dlinkGreenLEDShutoff 1 } dlinkGreenLEDShutoffState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Green disable LED function. Default is disabled." DEFVAL { disabled } ::= { dlinkGreenLEDShutoff 2 } dlinkGreenLEDShutoffTimeProfile1 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time profile name associated with the Schedule entry (e.g., `abc, bbb')." ::= { dlinkGreenLEDShutoff 3} dlinkGreenLEDShutoffTimeProfile2 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time profile name associated with the Schedule entry (e.g., `abc, bbb')." ::= { dlinkGreenLEDShutoff 4} -- --------------------------------------------------------------------- -- Green Disable Port -- --------------------------------------------------------------------- dlinkGreenPortShutoffPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Provides control to disable LED port." ::= { dlinkGreenPortShutoff 1 } dlinkGreenPortShutoffState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Green disable LED function. Default is disabled." DEFVAL { disabled } ::= { dlinkGreenPortShutoff 2 } dlinkGreenPortShutoffTimeProfile1 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time profile name associated with the Schedule entry (e.g., `abc, bbb')." ::= { dlinkGreenPortShutoff 3} dlinkGreenPortShutoffTimeProfile2 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time profile name associated with the Schedule entry (e.g., `abc, bbb')." ::= { dlinkGreenPortShutoff 4} -- --------------------------------------------------------------------- -- Green System Hibernation mode -- --------------------------------------------------------------------- dlinkGreenSystemHibernationState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Green disable LED function. Default is disabled." DEFVAL { disabled } ::= { dlinkGreenSystemHibernation 1 } dlinkGreenSystemHibernationTimeProfile1 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time profile name associated with the Schedule entry (e.g., `abc, bbb')." ::= { dlinkGreenSystemHibernation 2} dlinkGreenSystemHibernationTimeProfile2 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time profile name associated with the Schedule entry (e.g., `abc, bbb')." ::= { dlinkGreenSystemHibernation 3} dlinkPowerSavingGlobalSetting OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Power Saving global setting. Default is disabled." DEFVAL { disabled } ::= { companyGreenSetting 6 } -- ---------------------------------------------------------- -- The companySecurity Groups -- ---------------------------------------------------------- securityDhcpServerScreen OBJECT IDENTIFIER ::= { companySecurity 7 } -- Port Security Group --------------------------------------------- -- dhcpServerScreenEnablePortlist OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "To enable or disable DHCP Server Screening port list." ::= { securityDhcpServerScreen 1 } --Trused Server Group -- dhcpServerScreenTrustedServerTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpServerScreenTrustedServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the configuration objects for the DHCP server screen server list. An entry appears in this table for each port that may authenticate access to itself." ::= { securityDhcpServerScreen 3 } dhcpServerScreenTrustedServerEntry OBJECT-TYPE SYNTAX DhcpServerScreenTrustedServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration information for an DHCP server screen server." INDEX { dhcpServerScreenTrustedServerIndex } ::= { dhcpServerScreenTrustedServerTable 1 } DhcpServerScreenTrustedServerEntry ::= SEQUENCE { dhcpServerScreenTrustedServerIndex INTEGER, dhcpServerScreenTrustedServerAddress Ipv6Address, dhcpServerScreenIPType INTEGER, dhcpServerScreenTrustedServerStatus RowStatus } dhcpServerScreenTrustedServerIndex OBJECT-TYPE SYNTAX INTEGER (1..5) MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value for DHCP server screen server index. Its value ranges between 1 and 5." ::= { dhcpServerScreenTrustedServerEntry 1 } dhcpServerScreenTrustedServerAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the DHCP server screen server referred to in this table entry." ::= { dhcpServerScreenTrustedServerEntry 2 } dhcpServerScreenIPType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of IP interface." ::= { dhcpServerScreenTrustedServerEntry 3 } dhcpServerScreenTrustedServerStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The dhcpServerScreenServerIndex objects must be explicitly set." ::= { dhcpServerScreenTrustedServerEntry 4} securityTrafficSeg OBJECT IDENTIFIER ::= { companySecurity 9} trafficSegStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Status of Traffic Segmention." ::= { securityTrafficSeg 1 } -- -- Port Map Table -- trafficSegTable OBJECT-TYPE SYNTAX SEQUENCE OF TrafficSegEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel" ::= { securityTrafficSeg 2 } trafficSegEntry OBJECT-TYPE SYNTAX TrafficSegEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each created port-channel port" INDEX { trafficSegIfIndex } ::= { trafficSegTable 1 } TrafficSegEntry ::= SEQUENCE { trafficSegIfIndex InterfaceIndex, trafficSegMemberList PortList } trafficSegIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The port index of Traffic Segmentation table." ::= { trafficSegEntry 1 } trafficSegMemberList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Forwarding member port list of Traffic Segmentation port index." ::= { trafficSegEntry 2 } -- ---------------------------------------------------------- -- The companyDoSCtrl Groups -- ---------------------------------------------------------- doSCtrlState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of the DoS prevention type." ::= { companyDoSCtrl 1 } doSCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF DoSCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that holds the DoS prevention settings of the device." ::= { companyDoSCtrl 2 } doSCtrlEntry OBJECT-TYPE SYNTAX DoSCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of DoS prevention settings of the device." INDEX { doSCtrlType } ::= { doSCtrlTable 1 } DoSCtrlEntry ::= SEQUENCE { doSCtrlType INTEGER, doSCtrlDisplayState INTEGER } doSCtrlType OBJECT-TYPE SYNTAX INTEGER { landattack(1), blatattack(2), -- smurfattack(3), /*WS5 not support*/ tcpnullscan(4), tcpxmascan(5), tcpsynfin(6), tcpsynsrcportless1024(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the DoS prevention type." ::= { doSCtrlEntry 1 } doSCtrlDisplayState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of the DoS prevention type." ::= { doSCtrlEntry 2 } -- ---------------------------------------------------------------- -- The RMON group -- ---------------------------------------------------------------- rmonGlobalState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling RMON function." ::= { companyRMON 1 } rmonStatistics OBJECT IDENTIFIER ::= { companyRMON 2 } rmonHistory OBJECT IDENTIFIER ::= { companyRMON 3 } rmonAlarm OBJECT IDENTIFIER ::= { companyRMON 4 } rmonEvent OBJECT IDENTIFIER ::= { companyRMON 5 } -- The Ethernet Statistics Group -- -- Implementation of the Ethernet Statistics group is optional. -- Consult the MODULE-COMPLIANCE macro for the authoritative -- conformance information for this MIB. -- -- The ethernet statistics group contains statistics measured by the -- probe for each monitored interface on this device. These -- statistics take the form of free running counters that start from -- zero when a valid entry is created. -- -- This group currently has statistics defined only for -- Ethernet interfaces. Each etherStatsEntry contains statistics -- for one Ethernet interface. The probe must create one -- etherStats entry for each monitored Ethernet interface -- on the device. rmonStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF RmonStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Ethernet statistics entries." ::= { rmonStatistics 1 } rmonStatsEntry OBJECT-TYPE SYNTAX RmonStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named etherStatsPkts.1" INDEX { rmonStatsIndex } ::= { rmonStatsTable 1 } RmonStatsEntry ::= SEQUENCE { rmonStatsIndex Integer32, rmonStatsDataSource OBJECT IDENTIFIER, rmonStatsOwner OCTET STRING, rmonStatsStatus RmonStatus } rmonStatsIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object uniquely identifies this etherStats entry." ::= { rmonStatsEntry 1 } rmonStatsDataSource OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "This object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated etherStatsStatus object is equal to valid(1)." ::= { rmonStatsEntry 2 } rmonStatsOwner OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it." ::= { rmonStatsEntry 3 } rmonStatsStatus OBJECT-TYPE SYNTAX RmonStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this etherStats entry." ::= { rmonStatsEntry 4 } -- The History Control Group -- Implementation of the History Control group is optional. -- Consult the MODULE-COMPLIANCE macro for the authoritative -- conformance information for this MIB. -- -- The history control group controls the periodic statistical -- sampling of data from various types of networks. The -- historyControlTable stores configuration entries that each -- define an interface, polling period, and other parameters. -- Once samples are taken, their data is stored in an entry -- in a media-specific table. Each such entry defines one -- sample, and is associated with the historyControlEntry that -- caused the sample to be taken. Each counter in the -- etherHistoryEntry counts the same event as its similarly-named -- counterpart in the etherStatsEntry, except that each value here -- is a cumulative sum during a sampling period. -- -- If the probe keeps track of the time of day, it should start -- the first sample of the history at a time such that -- when the next hour of the day begins, a sample is -- started at that instant. This tends to make more -- user-friendly reports, and enables comparison of reports -- from different probes that have relatively accurate time -- of day. -- -- The probe is encouraged to add two history control entries -- per monitored interface upon initialization that describe a short -- term and a long term polling period. Suggested parameters are 30 -- seconds for the short term polling period and 30 minutes for -- the long term period. rmonHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF RmonHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of history control entries." ::= { rmonHistory 1 } rmonHistoryEntry OBJECT-TYPE SYNTAX RmonHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of parameters that set up a periodic sampling of statistics. As an example, an instance of the historyControlInterval object might be named historyControlInterval.2" INDEX { rmonHistoryIndex } ::= { rmonHistoryTable 1 } RmonHistoryEntry ::= SEQUENCE { rmonHistoryIndex Integer32, rmonHistoryDataSource OBJECT IDENTIFIER, rmonHistoryBucketsRequested Integer32, rmonHistoryInterval Integer32, rmonHistoryOwner OCTET STRING, rmonHistoryStatus RmonStatus } rmonHistoryIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device." ::= { rmonHistoryEntry 1 } rmonHistoryDataSource OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated historyControlStatus object is equal to valid(1)." ::= { rmonHistoryEntry 2 } rmonHistoryBucketsRequested OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry. When this object is created or modified, the probe should set historyControlBucketsGranted as closely to this object as is possible for the particular probe implementation and available resources." DEFVAL { 50 } ::= { rmonHistoryEntry 3 } rmonHistoryInterval OBJECT-TYPE SYNTAX Integer32 (1..3600) UNITS "Seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControlEntry. This interval can be set to any number of seconds between 1 and 3600 (1 hour). Because the counters in a bucket may overflow at their maximum value with no indication, a prudent manager will take into account the possibility of overflow in any of the associated counters. It is important to consider the minimum time in which any counter could overflow on a particular media type and set the historyControlInterval object to a value less than this interval. This is typically most important for the 'octets' counter in any media-specific table. For example, on an Ethernet network, the etherHistoryOctets counter could overflow in about one hour at the Ethernet's maximum utilization. This object may not be modified if the associated historyControlStatus object is equal to valid(1)." DEFVAL { 1800 } ::= { rmonHistoryEntry 4 } rmonHistoryOwner OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it." ::= { rmonHistoryEntry 5 } rmonHistoryStatus OBJECT-TYPE SYNTAX RmonStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if this historyControlEntry is not equal to valid(1)." ::= { rmonHistoryEntry 6 } -- The Alarm Group -- Implementation of the Alarm group is optional. The Alarm Group -- requires the implementation of the Event group. -- Consult the MODULE-COMPLIANCE macro for the authoritative -- conformance information for this MIB. -- -- The Alarm group periodically takes statistical samples from -- variables in the probe and compares them to thresholds that have -- been configured. The alarm table stores configuration -- entries that each define a variable, polling period, and -- threshold parameters. If a sample is found to cross the -- threshold values, an event is generated. Only variables that -- resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, -- Counter32, Counter64, Gauge32, or TimeTicks) may be monitored in -- this way. -- -- This function has a hysteresis mechanism to limit the generation -- of events. This mechanism generates one event as a threshold -- is crossed in the appropriate direction. No more events are -- generated for that threshold until the opposite threshold is -- crossed. -- -- In the case of a sampling a deltaValue, a probe may implement -- this mechanism with more precision if it takes a delta sample -- twice per period, each time comparing the sum of the latest two -- samples to the threshold. This allows the detection of threshold -- crossings that span the sampling boundary. Note that this does -- not require any special configuration of the threshold value. -- It is suggested that probes implement this more precise algorithm. rmonAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF RmonAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of alarm entries." ::= { rmonAlarm 1 } rmonAlarmEntry OBJECT-TYPE SYNTAX RmonAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of parameters that set up a periodic checking for alarm conditions. For example, an instance of the alarmValue object might be named alarmValue.8" INDEX { rmonAlarmIndex } ::= { rmonAlarmTable 1 } RmonAlarmEntry ::= SEQUENCE { rmonAlarmIndex Integer32, rmonAlarmInterval Integer32, rmonAlarmVariable OBJECT IDENTIFIER, rmonAlarmSampleType INTEGER, rmonAlarmRisingThreshold Integer32, rmonAlarmFallingThreshold Integer32, rmonAlarmRisingEventIndex Integer32, rmonAlarmFallingEventIndex Integer32, rmonAlarmOwner OCTET STRING, rmonAlarmStatus RmonStatus } rmonAlarmIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "An index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device." ::= { rmonAlarmEntry 1 } rmonAlarmInterval OBJECT-TYPE SYNTAX Integer32 UNITS "Seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be taken in the case of deltaValue sampling - the interval should be set short enough that the sampled variable is very unlikely to increase or decrease by more than 2^31 - 1 during a single sampling interval. This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 2 } rmonAlarmVariable OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter32, Counter64, Gauge, or TimeTicks) may be sampled. Because SNMP access control is articulated entirely in terms of the contents of MIB views, no access control mechanism exists that can restrict the value of this object to identify only those objects that exist in a particular MIB view. Because there is thus no acceptable means of restricting the read access that could be obtained through the alarm mechanism, the probe must only grant write access to this object in those views that have read access to all objects on the probe. During a set operation, if the supplied variable name is not available in the selected MIB view, a badValue error must be returned. If at any time the variable name of an established alarmEntry is no longer available in the selected MIB view, the probe must change the status of this alarmEntry to invalid(4). This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 3 } rmonAlarmSampleType OBJECT-TYPE SYNTAX INTEGER { absoluteValue(1), deltaValue(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), the value of the selected variable will be compared directly with the thresholds at the end of the sampling interval. If the value of this object is deltaValue(2), the value of the selected variable at the last sample will be subtracted from the current value, and the difference compared with the thresholds. This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 4 } rmonAlarmRisingThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "A threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval was less than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is greater than or equal to this threshold and the associated alarmStartupAlarm is equal to risingAlarm(1) or risingOrFallingAlarm(3). After a rising event is generated, another such event will not be generated until the sampled value falls below this threshold and reaches the alarmFallingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 5 } rmonAlarmFallingThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "A threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was greater than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is less than or equal to this threshold and the associated alarmStartupAlarm is equal to fallingAlarm(2) or risingOrFallingAlarm(3). After a falling event is generated, another such event will not be generated until the sampled value rises above this threshold and reaches the alarmRisingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 6 } rmonAlarmRisingEventIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 7 } rmonAlarmFallingEventIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 8 } rmonAlarmOwner OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it." ::= { rmonAlarmEntry 9 } rmonAlarmStatus OBJECT-TYPE SYNTAX RmonStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this alarm entry." ::= { rmonAlarmEntry 10 } -- The Event Group -- Implementation of the Event group is optional. -- Consult the MODULE-COMPLIANCE macro for the authoritative -- conformance information for this MIB. -- -- The Event group controls the generation and notification -- of events from this device. Each entry in the eventTable -- describes the parameters of the event that can be triggered. -- Each event entry is fired by an associated condition located -- elsewhere in the MIB. An event entry may also be associated -- with a function elsewhere in the MIB that will be executed -- when the event is generated. For example, a channel may -- be turned on or off by the firing of an event. -- -- Each eventEntry may optionally specify that a log entry -- be created on its behalf whenever the event occurs. -- Each entry may also specify that notification should -- occur by way of SNMP trap messages. In this case, the -- community for the trap message is given in the associated -- eventCommunity object. The enterprise and specific trap -- fields of the trap are determined by the condition that -- triggered the event. Two traps are defined: risingAlarm and -- fallingAlarm. If the eventTable is triggered by a condition -- specified elsewhere, the enterprise and specific trap fields -- must be specified for traps generated for that condition. rmonEventTable OBJECT-TYPE SYNTAX SEQUENCE OF RmonEventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of events to be generated." ::= { rmonEvent 1 } rmonEventEntry OBJECT-TYPE SYNTAX RmonEventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of parameters that describe an event to be generated when certain conditions are met. As an example, an instance of the eventLastTimeSent object might be named eventLastTimeSent.6" INDEX { rmonEventIndex } ::= { rmonEventTable 1 } RmonEventEntry ::= SEQUENCE { rmonEventIndex Integer32, rmonEventDescription DisplayString, rmonEventType INTEGER, rmonEventCommunity OCTET STRING, rmonEventOwner OCTET STRING, rmonEventStatus RmonStatus } rmonEventIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "An index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur." ::= { rmonEventEntry 1 } rmonEventDescription OBJECT-TYPE SYNTAX DisplayString (SIZE (0..127)) MAX-ACCESS read-create STATUS current DESCRIPTION "A comment describing this event entry." ::= { rmonEventEntry 2 } rmonEventType OBJECT-TYPE SYNTAX INTEGER { none(1), log(2), snmptrap(3), -- send an SNMP trap logandtrap(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-trap, an SNMP trap is sent to one or more management stations." ::= { rmonEventEntry 3 } rmonEventCommunity OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "If an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string." ::= { rmonEventEntry 4 } rmonEventOwner OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has associated entries in the log table, all connected management stations should retrieve those log entries, as they may have significance to all management stations connected to this device" ::= { rmonEventEntry 5 } rmonEventStatus OBJECT-TYPE SYNTAX RmonStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent." ::= { rmonEventEntry 6 } -- ---------------------------------------------------------------- -- The Neighbor Setting group -- ---------------------------------------------------------------- neighborTable OBJECT-TYPE SYNTAX SEQUENCE OF NeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the Neighbor Cache Table." ::= { companyNeighbor 1 } neighborEntry OBJECT-TYPE SYNTAX NeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Neighbor cache entry containing the ifindex and ipv6 addr." INDEX { neighborIfindex, neighborIPv6Addr, neighborMACAddr} ::= { neighborTable 1 } NeighborEntry ::= SEQUENCE { neighborIfindex INTEGER, neighborIPv6Addr Ipv6Address, neighborMACAddr MacAddress, neighborType INTEGER, neighborCacheState INTEGER, neighborRowStatus RowStatus } neighborIfindex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index of the Neighbor entry." ::= { neighborEntry 1 } neighborIPv6Addr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "Allows the entry of an IP address that will be a Neighbor entry into the Neighbor Cache Table." ::= { neighborEntry 2 } neighborMACAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the Neighbor entry." ::= { neighborEntry 3 } neighborType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type associated of the Neighbor entry." ::= { neighborEntry 4 } neighborCacheState OBJECT-TYPE SYNTAX INTEGER { static(1), reachable(2), incomplete(3), stale(4), delay(5), probe(6), notinservice(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type associated of the Neighbor entry." ::= { neighborEntry 5 } neighborRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of an entry in the Neighbor Cache Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available." ::= { neighborEntry 7 } -- ---------------------------------------------------------- -- The DHCP Relay -- ---------------------------------------------------------- dhcpRelayControl OBJECT IDENTIFIER ::= { companyDHCPRelay 1 } dhcpRelayManagement OBJECT IDENTIFIER ::= { companyDHCPRelay 2 } dhcpRelayManagementOption82 OBJECT IDENTIFIER ::= { dhcpRelayManagement 2 } -- The DHCP Relay Control dhcpRelayState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP relay function is enabled or disabled." ::= { dhcpRelayControl 1 } dhcpRelayHopCount OBJECT-TYPE SYNTAX INTEGER (1..16) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the maximum number of router hops that the packets can cross." ::= { dhcpRelayControl 2 } dhcpRelayTimeThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet." ::= { dhcpRelayControl 3 } -- The DHCP Relay Management -- The DHCP Relay Interface Settings Table dhcpRelayInterfaceSettingsTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpRelayInterfaceSettingsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the IP address as a destination to forward (relay) DHCP packets to." ::= { dhcpRelayManagement 1 } dhcpRelayInterfaceSettingsEntry OBJECT-TYPE SYNTAX DhcpRelayInterfaceSettingsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information indicates the IP address as a destination to forward (relay) DHCP packets to." INDEX { dhcpRelayInterface, dhcpRelayServerIP} ::= { dhcpRelayInterfaceSettingsTable 1 } DhcpRelayInterfaceSettingsEntry ::= SEQUENCE { dhcpRelayInterface DisplayString, dhcpRelayServerIP IpAddress, dhcpRelayInterfaceSettingsRowStatus RowStatus } dhcpRelayInterface OBJECT-TYPE SYNTAX DisplayString (SIZE(0..12)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the name of the IP interface." ::= { dhcpRelayInterfaceSettingsEntry 1 } dhcpRelayServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the DHCP server IP address." ::= { dhcpRelayInterfaceSettingsEntry 2 } dhcpRelayInterfaceSettingsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available." ::= { dhcpRelayInterfaceSettingsEntry 3 } -- The DHCP Relay Management -- The DHCP Relay Option82 dhcpRelayOption82State OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates DHCP relay option 82 function always enabled." ::= { dhcpRelayManagementOption82 1 } dhcpRelayOption82CheckState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP relay option 82 Check function is enabled or disabled." ::= { dhcpRelayManagementOption82 2 } dhcpRelayOption82Policy OBJECT-TYPE SYNTAX INTEGER { replace(1), drop(2), keep(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP relay option 82 policy." ::= { dhcpRelayManagementOption82 3 } dhcpRelayOption82RemoteIDType OBJECT-TYPE SYNTAX INTEGER { default(1), userdefined(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the type of remote ID. If the type is default, the remote ID will be the MAC address of the device, otherwise, the remote ID can be defined by writing to the swDHCPRelayOption82RemoteID object." ::= { dhcpRelayManagementOption82 4 } dhcpRelayOption82RemoteID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object displays the current remote ID of the device. If swDHCPRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If swDHCPRelayOption82RemoteIDType is set to user-defined, a new value can be written to this object." ::= { dhcpRelayManagementOption82 5 } -- ---------------------------------------------------------- -- The DHCP LocalRelay -- ---------------------------------------------------------- -- The DHCP Local Relay Table dhcpLocalRelayGlobalState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP local relay function of VLAN is enabled or disabled." ::= { companyDHCPLocalRelay 1 } dhcpLocalRelayTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpLocalRelayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the IP address as a destination to forward (local relay) DHCP packets to." ::= { companyDHCPLocalRelay 2 } dhcpLocalRelayEntry OBJECT-TYPE SYNTAX DhcpLocalRelayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information indicates the IP address as a destination to forward (local relay) DHCP packets to." INDEX { dhcpLocalRelaySettingsVLANID } ::= { dhcpLocalRelayTable 1 } DhcpLocalRelayEntry ::= SEQUENCE { dhcpLocalRelaySettingsVLANID INTEGER, dhcpLocalRelaySettingsState INTEGER } dhcpLocalRelaySettingsVLANID OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays the current VLAN ID of the device." ::= { dhcpLocalRelayEntry 1 } dhcpLocalRelaySettingsState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP local relay function of VLAN is enabled or disabled." ::= { dhcpLocalRelayEntry 2 } dhcpv6RelayControl OBJECT IDENTIFIER ::= { companyDHCPv6Relay 1 } dhcpv6RelayManagement OBJECT IDENTIFIER ::= { companyDHCPv6Relay 2 } dhcpv6RelayOption37 OBJECT IDENTIFIER ::= { companyDHCPv6Relay 3 } -- ---------------------------------------------------------- -- The DHCPv6 Relay -- ---------------------------------------------------------- -- The DHCPv6 Relay Control dhcpv6RelayState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCPv6 relay function is enabled or disabled." ::= { dhcpv6RelayControl 1 } dhcpv6RelayHopCount OBJECT-TYPE SYNTAX INTEGER (1..32) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the maximum number of router hops that the DHCPv6 packets can cross." ::= { dhcpv6RelayControl 2 } -- The DHCPv6 Relay Management -- The DHCPv6 Relay Interface Settings Table dhcpv6RelayInterfaceSettingsTable OBJECT-TYPE SYNTAX SEQUENCE OF Dhcpv6RelayInterfaceSettingsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the IP address as a destination to forward (relay) DHCP packets to." ::= { dhcpv6RelayManagement 1 } dhcpv6RelayInterfaceSettingsEntry OBJECT-TYPE SYNTAX Dhcpv6RelayInterfaceSettingsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information indicates the IP address as a destination to forward (relay) DHCP packets to." INDEX { dhcpv6RelayInterface, dhcpv6RelayServerIP} ::= { dhcpv6RelayInterfaceSettingsTable 1 } Dhcpv6RelayInterfaceSettingsEntry ::= SEQUENCE { dhcpv6RelayInterface DisplayString, dhcpv6RelayServerIP Ipv6Address, dhcpv6RelayInterfaceSettingsRowStatus RowStatus } dhcpv6RelayInterface OBJECT-TYPE SYNTAX DisplayString (SIZE(0..12)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum number of router hops that the DHCPv6 packets can cross." ::= { dhcpv6RelayInterfaceSettingsEntry 1 } dhcpv6RelayServerIP OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the DHCP server IP address." ::= { dhcpv6RelayInterfaceSettingsEntry 2 } dhcpv6RelayInterfaceSettingsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available." ::= { dhcpv6RelayInterfaceSettingsEntry 99 } -- The DHCPv6 Relay Option37 dhcpv6RelayOption37State OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCPv6 relay option 37 function is enabled or disabled." ::= { dhcpv6RelayOption37 1 } dhcpv6RelayOption37CheckState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCPv6 relay option 37 Check function is enabled or disabled." ::= { dhcpv6RelayOption37 2 } -- dhcpv6RelayOption37Policy OBJECT-TYPE -- SYNTAX INTEGER { -- replace(1), -- drop(2), -- keep(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "This object indicates DHCPv6 relay option 37 policy." -- ::= { dhcpv6RelayOption37 3 } dhcpv6RelayOption37RemoteIDType OBJECT-TYPE SYNTAX INTEGER { default(0), cid_with_user_define(1), user_define(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the type of remote ID." ::= { dhcpv6RelayOption37 3 } dhcpv6RelayOption37RemoteID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object displays the current remote ID of the device. If RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If RemoteIDType is set to user-defined, a new value can be written to this object." ::= { dhcpv6RelayOption37 4 } -- ***************************************************************** -- -- Enterprise Trap group -- -- ***************************************************************** END