-------------------------------------------------------------------------------- -- --------------------------- Revision ---------------------------------------- -- Date Version Author Chanage Description -- -- 2015/01/09 6.11.014 D-Link 1.Add Mac Notification -- 2014/12/05 6.11.013 D-Link 1.Add sysPortCtrlCapability, sysDhcpAutoImage, -- sysBootupConfigID, sysBootupImage, -- cosBandwidthEffectiveRX and cosBandwidthEffectiveTX. -- -- 2014/07/30 6.11.009 D-Link 1.sync release version with firmware. -- -- 2014/07/11 6.11.R005 D-Link 1.Add MultiIPInterface. -- -- 2014/06/26 6.11.R004B D-Link 1.Add impbLogState -- 2.Modify aacAccounting description. -- -- 2014/06/04 6.11.R001 D-Link 1.Add RADIUS and TACACS+ accounting. -- 2.Add sfpVendorInfoTable. -- 3.Add DdmCtrl and ddmInfo. -- -- 2014/05/30 6.10.B022 D-Link 1.Add GreenSetting. -- 2.Add PortUpLinkTime. -- -- 2014/03/18 6.10.005 D-Link 1.Support DNA tool -- 2.Add companydot3azEEE. -- -- 2014/03/06 6.10.004 D-Link 1.ACL rule support vlan based mode -- 2.Modify sysPortCtrlMediumType value. -- -- 2014/02/19 6.10.003 D-Link 1.Changed the sysPortCtrlMediumType valuelist. -- 2.Changed the sysPortCtrlType valuelist. -- -- 2013/12/06 6.10.002 D-Link 1.Hardware version changed from C1 to A1 -- -- 2013/11/20 6.10.001 D-Link 1.Initial version. -- -- -------------------------- Revision End ------------------------------------- -------------------------------------------------------------------------------- DGS-1210-28ME_AX DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, enterprises, IpAddress, Integer32, Unsigned32, TimeTicks, Counter32 FROM SNMPv2-SMI InetAddress FROM INET-ADDRESS-MIB InterfaceIndex,InterfaceIndexOrZero FROM IF-MIB SnmpAdminString,SnmpEngineID,SnmpSecurityLevel FROM SNMP-FRAMEWORK-MIB dot1dBridge, dot1dBasePortEntry, dot1dBasePort FROM BRIDGE-MIB RowStatus, TruthValue, DisplayString, TEXTUAL-CONVENTION, MacAddress FROM SNMPv2-TC VlanId FROM Q-BRIDGE-MIB AddressFamilyNumbers FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB; d-link OBJECT IDENTIFIER ::= { enterprises 171 } dlink-products OBJECT IDENTIFIER ::= { d-link 10 } dlink-DGS12XXSeriesProd OBJECT IDENTIFIER ::= { dlink-products 76} dgs-1210-28me OBJECT IDENTIFIER ::= { dlink-DGS12XXSeriesProd 28 } dgs-1210-28meax OBJECT IDENTIFIER ::= { dgs-1210-28me 1 } VlanIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095 then it represents a VLAN with scope local to the particular agent, i.e. one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q but it is convenient to be able to manage them in the same way using this MIB." SYNTAX Unsigned32 PortList ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'." SYNTAX OCTET STRING BridgeId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to refer to a bridge in a unique fashion (typically, the numerically smallest MAC address of all ports on the bridge). Several objects in this MIB module represent values of timers used by the Spanning Tree Protocol. In this MIB, these timers have values in units of hundreths of a second (i.e. 1/100 secs). These timers, when stored in a Spanning Tree Protocol's BPDU, are in units of 1/256 seconds. Note, however, that 802.1D-1990 specifies a settable granularity of no more than 1 second for these timers. To avoid ambiguity, a data type is defined here as a textual convention and all representation of these timers in this MIB module are defined using this data type. An algorithm is also defined for converting between the different units, to ensure a timer's value is not distorted by multiple conversions." SYNTAX OCTET STRING (SIZE (8)) Timeout ::= TEXTUAL-CONVENTION DISPLAY-HINT "d4" STATUS current DESCRIPTION "A STP timer in units of 1/100 seconds To convert a Timeout value into a value in units of 1/256 seconds, the following algorithm should be used: b = floor( (n * 256) / 100) where: floor = quotient [ignore remainder] n is the value in 1/100 second units b is the value in 1/256 second units To convert the value from 1/256 second units back to 1/100 seconds, the following algorithm should be used: n = ceiling( (b * 100) / 256) where: ceiling = quotient [if remainder is 0], or quotient + 1 [if remainder is non-zero] n is the value in 1/100 second units b is the value in 1/256 second units Note: it is important that the arithmetic operations are done in the order specified (i.e., multiply first, divide second)." SYNTAX INTEGER LldpManAddress ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The value of a management address associated with the LLDP agent that may be used to reach higher layer entities to assist discovery by network management. It should be noted that appropriate security credentials, such as SNMP engineId, may be required to access the LLDP agent using a management address. These necessary credentials should be known by the network management and the objects associated with the credentials are not included in the LLDP agent." SYNTAX OCTET STRING (SIZE (1..31)) OwnerString ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type is used to model an administratively assigned name of the owner of a resource. Implementations must accept values composed of well-formed NVT ASCII sequences. In addition, implementations should accept values composed of well-formed UTF-8 sequences. It is suggested that this name contain one or more of the following: IP address, management station name, network manager's name, location, or phone number. In some cases the agent itself will be the owner of an entry. In these cases, this string shall be set to a string starting with 'monitor'. SNMP access control is articulated entirely in terms of the contents of MIB views; access to a particular SNMP object instance depends only upon its presence or absence in a particular MIB view and never upon its value or the value of related object instances. Thus, objects of this type afford resolution of resource contention only among cooperating managers; they realize no access control function with respect to uncooperative parties." SYNTAX OCTET STRING (SIZE (0..127)) RmonStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The status of a table entry. Setting this object to the value invalid(4) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries currently not in use. Proper interpretation of such entries requires examination of the relevant RmonStatus object. An existing instance of this object cannot be set to createRequest(2). This object may only be set to createRequest(2) when this instance is created. When this object is created, the agent may wish to create supplemental object instances with default values to complete a conceptual row in this table. Because the creation of these default objects is entirely at the option of the agent, the manager must not assume that any will be created, but may make use of any that are created. Immediately after completing the create operation, the agent must set this object to underCreation(3). When in the underCreation(3) state, an entry is allowed to exist in a possibly incomplete, possibly inconsistent state, usually to allow it to be modified in multiple PDUs. When in this state, an entry is not fully active. Entries shall exist in the underCreation(3) state until the management station is finished configuring the entry and sets this object to valid(1) or aborts, setting this object to invalid(4). If the agent determines that an entry has been in the underCreation(3) state for an abnormally long time, it may decide that the management station has crashed. If the agent makes this decision, it may set this object to invalid(4) to reclaim the entry. A prudent agent will understand that the management station may need to wait for human input and will allow for that possibility in its determination of this abnormally long period. An entry in the valid(1) state is fully configured and consistent and fully represents the configuration or operation such a row is intended to represent. For example, it could be a statistical function that is configured and active, or a filter that is available in the list of filters processed by the packet capture process. A manager is restricted to changing the state of an entry in the following ways: To: valid createRequest underCreation invalid From: valid OK NO OK OK createRequest N/A N/A N/A N/A underCreation OK NO OK OK invalid NO NO NO OK nonExistent NO OK NO OK In the table above, it is not applicable to move the state from the createRequest state to any other state because the manager will never find the variable in that state. The nonExistent state is not a value of the enumeration, rather it means that the entryStatus variable does not exist at all. An agent may allow an entryStatus variable to change state in additional ways, so long as the semantics of the states are followed. This allowance is made to ease the implementation of the agent and is made despite the fact that managers should never exercise these additional state transitions." SYNTAX INTEGER { valid(1), createRequest(2), underCreation(3), invalid(4) } Ipv6Address ::= TEXTUAL-CONVENTION DISPLAY-HINT "2x:" STATUS current DESCRIPTION "This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order." SYNTAX OCTET STRING (SIZE (16)) -- ----------------------------------------------------------------- -- -- groups in the MIB -- ----------------------------------------------------------------- -- -- end DLINK_METRO_LIKE_FIRMWARE_INFO_DISPLAY -- start DLINK_METRO_LIKE_FIRMWARE_INFO_DISPLAY companySystem OBJECT IDENTIFIER ::= { dgs-1210-28meax 1 } companyIpifGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 2 } companyTftpGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 3 } companyMiscGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 4 } companySNMPV3 OBJECT IDENTIFIER ::= { dgs-1210-28meax 5 } companySTP OBJECT IDENTIFIER ::= { dgs-1210-28meax 6 } companyDot1qVlanGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 7 } companyLA OBJECT IDENTIFIER ::= { dgs-1210-28meax 8 } companyStaticMAC OBJECT IDENTIFIER ::= { dgs-1210-28meax 9 } companyIgsGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 10 } companyGVRPGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 11 } companyQoSGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 12 } companyTrafficMgmt OBJECT IDENTIFIER ::= { dgs-1210-28meax 13 } companySecurity OBJECT IDENTIFIER ::= { dgs-1210-28meax 14 } companyACLGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 15 } companySyslog OBJECT IDENTIFIER ::= { dgs-1210-28meax 16 } companyLBD OBJECT IDENTIFIER ::= { dgs-1210-28meax 17 } companyMirror OBJECT IDENTIFIER ::= { dgs-1210-28meax 18 } companyStaticMcast OBJECT IDENTIFIER ::= { dgs-1210-28meax 19 } companySNTPSetting OBJECT IDENTIFIER ::= { dgs-1210-28meax 20 } companyRMON OBJECT IDENTIFIER ::= { dgs-1210-28meax 22 } companyAuthGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 23 } companyGuestVlan OBJECT IDENTIFIER ::= { dgs-1210-28meax 24 } companyMacNotify OBJECT IDENTIFIER ::= { dgs-1210-28meax 25 } companyISMVLAN OBJECT IDENTIFIER ::= { dgs-1210-28meax 27 } companyDHCPRelay OBJECT IDENTIFIER ::= { dgs-1210-28meax 28 } companyDHCPLocalRelay OBJECT IDENTIFIER ::= { dgs-1210-28meax 29 } companyGreenSetting OBJECT IDENTIFIER ::= { dgs-1210-28meax 31 } sysFirmwareInfomation OBJECT IDENTIFIER ::= { companySystem 31 } companyLLDPSetting OBJECT IDENTIFIER ::= { dgs-1210-28meax 32 } companyCPUInterfaceFilterGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 33 } companyStaticARP OBJECT IDENTIFIER ::= { dgs-1210-28meax 34 } companyCableDiagnostic OBJECT IDENTIFIER ::= { dgs-1210-28meax 35 } companyVLANTrunk OBJECT IDENTIFIER ::= { dgs-1210-28meax 36 } companyTimeRangeMgmt OBJECT IDENTIFIER ::= { dgs-1210-28meax 38 } companySMTP OBJECT IDENTIFIER ::= { dgs-1210-28meax 40 } companyMultiIPInterface OBJECT IDENTIFIER ::= { dgs-1210-28meax 41 } companyLimitIp OBJECT IDENTIFIER ::= { dgs-1210-28meax 45 } companyGratuitousARP OBJECT IDENTIFIER ::= { dgs-1210-28meax 48 } companyNeighbor OBJECT IDENTIFIER ::= { dgs-1210-28meax 50 } companyEoam OBJECT IDENTIFIER ::= { dgs-1210-28meax 51 } companyDuld OBJECT IDENTIFIER ::= { dgs-1210-28meax 52 } companydot3azEEE OBJECT IDENTIFIER ::= { dgs-1210-28meax 53 } companyMacAuthGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 54 } companyWACAuthGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 55} companyMacBasedVlan OBJECT IDENTIFIER ::= { dgs-1210-28meax 70 } companyBPDUAttack OBJECT IDENTIFIER ::= { dgs-1210-28meax 77 } companyDHCPv6Relay OBJECT IDENTIFIER ::= { dgs-1210-28meax 86 } companyMldsGroup OBJECT IDENTIFIER ::= { dgs-1210-28meax 88 } companyPPPoE OBJECT IDENTIFIER ::= { dgs-1210-28meax 98 } companyDoSCtrl OBJECT IDENTIFIER ::= { dgs-1210-28meax 99 } companyAgentBasicInfo OBJECT IDENTIFIER ::= { dgs-1210-28meax 100 } companyProtocolVlan OBJECT IDENTIFIER ::= { dgs-1210-28meax 101 } companyL2PT OBJECT IDENTIFIER ::= { dgs-1210-28meax 102 } companyQinQ OBJECT IDENTIFIER ::= { dgs-1210-28meax 103 } companySfpVendorInfo OBJECT IDENTIFIER ::= { dgs-1210-28meax 104 } companyDDM OBJECT IDENTIFIER ::= { dgs-1210-28meax 105 } companyCpuProtect OBJECT IDENTIFIER ::= { dgs-1210-28meax 106 } -- ---------------------------------------------------------------- -- -- ------------------------------------------------------------------ -- companySystem -- ------------------------------------------------------------------ sysSwitchName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) V + _ = ." ::= { companySystem 1 } sysHardwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "Version number of the Hardware." DEFVAL { "" } ::= { companySystem 2 } sysFirmwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "Version number of the Firmware." DEFVAL { "" } ::= { companySystem 3 } sysLoginTimeoutInterval OBJECT-TYPE SYNTAX Integer32 (3..30) MAX-ACCESS read-write STATUS current DESCRIPTION "This time interval is used to count the time and logout web interface automatically." DEFVAL { 5 } ::= { companySystem 4 } sysLocationName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string." ::= { companySystem 5 } sysGroupInterval OBJECT-TYPE SYNTAX Integer32 (0 | 120..1225) MAX-ACCESS read-write STATUS current DESCRIPTION "Group Interval is used to send D-link Discover packet to D-link SmartConsole Utility frequency. The timer in units of seconds. Set value 0 to disable group Interval." ::= { companySystem 6 } sysSafeGuardEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set Safeguard Enable\Disable." DEFVAL { enable } ::= { companySystem 8 } sysRestart OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switch to be restarted. When the switch operationally goes down, configuration save operation is initiated based on the configuration save option chosen. When the switch operationally come up, the saved configurations are restored based on the restore option chosen. Once the switch is restarted, the value of this object reverts to 'false'." DEFVAL { false } ::= { companySystem 9 } sysSave OBJECT-TYPE SYNTAX INTEGER { True (1), False (2), config_1 (3), config_2 (4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to save Configuration , value 1 is save in process , value 2 is not in process , value 3 is save config_1 and value 4 is save config_2." DEFVAL { 1 } ::= { companySystem 10 } sysJumboFrameEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Gigabit Web Smart Switches support jumbo frames (frames larger than the Ethernet frame size of 1522 bytes) of up to 10,000 bytes (tagged). Default jumbo frame is disabled." DEFVAL { disable } ::= { companySystem 12 } -- Port Control Table sysPortCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF SysPortCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control the port specific parameters of the device like speed, duplex mode, etc." ::= { companySystem 13 } sysPortCtrlEntry OBJECT-TYPE SYNTAX SysPortCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system. Index to the table is the interface index of the port." INDEX { sysPortCtrlIndex , sysPortCtrlMediumType} ::= { sysPortCtrlTable 1 } SysPortCtrlEntry ::= SEQUENCE { sysPortCtrlIndex Integer32, sysPortCtrlMediumType INTEGER, sysPortCtrlSpeed INTEGER, sysPortCtrlOperStatus INTEGER, sysPortCtrlMDI INTEGER, sysPortCtrlFlowControl INTEGER, sysPortCtrlFlowControlOper INTEGER, sysPortCtrlType INTEGER, sysPortCtrlCapability BITS } sysPortCtrlIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface index of the port for the configuration in this entry applies." ::= { sysPortCtrlEntry 1 } sysPortCtrlMediumType OBJECT-TYPE SYNTAX INTEGER { copper(1), fiber(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the port type: fiber 1G/100M or copper." ::= { sysPortCtrlEntry 2 } sysPortCtrlSpeed OBJECT-TYPE SYNTAX INTEGER { rate1000M-Full (1), rate100M-Full (2), rate100M-Half (3), rate10M-Full (4), rate10M-Half (5), auto (6), disable (7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures interface speed." ::= { sysPortCtrlEntry 3 } sysPortCtrlOperStatus OBJECT-TYPE SYNTAX INTEGER { down (1), rate1000M-Full (2), rate100M-Full (3), rate100M-Half (4), rate10M-Full (5), rate10M-Half (6), rate10G-Full (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port's operating speed state." ::= { sysPortCtrlEntry 4 } sysPortCtrlMDI OBJECT-TYPE SYNTAX INTEGER { auto (1), mdi (2), mdix (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures interface auto/mdi/mdix mode. The default setting is Auto." ::= { sysPortCtrlEntry 5 } sysPortCtrlFlowControl OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables / disables flow control for the interface." ::= { sysPortCtrlEntry 6 } sysPortCtrlFlowControlOper OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The link parner negotiate port's operating flow control state." ::= { sysPortCtrlEntry 7 } sysPortCtrlType OBJECT-TYPE SYNTAX INTEGER { fastethernet(1), gigabitethernet(2), fiberwith100BaseSFPModule(3), fiberwith1GBaseSFPModule(4), fiberwith10GBaseSFPModule(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port's media type." ::= { sysPortCtrlEntry 8 } sysPortCtrlCapability OBJECT-TYPE SYNTAX BITS { rate10_half(0), rate10_full(1), rate100_half(2), rate100_full(3), reserve(4), rate1000_full(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "The port's capability advertised." ::= { sysPortCtrlEntry 9 } -- start DLINK_METRO_LIKE_GENERAL sysPortDescriptionTable OBJECT-TYPE SYNTAX SEQUENCE OF SysPortDescriptionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port description table." ::= { companySystem 14 } sysPortDescriptionEntry OBJECT-TYPE SYNTAX SysPortDescriptionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port description entry." INDEX { sysPortDescIndex, sysPortDescMediumType } ::= { sysPortDescriptionTable 1 } SysPortDescriptionEntry ::= SEQUENCE { sysPortDescIndex INTEGER, sysPortDescMediumType INTEGER, sysPortDescString DisplayString, sysPortUpLinkTime DisplayString } sysPortDescIndex OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the port index." ::= { sysPortDescriptionEntry 1 } sysPortDescMediumType OBJECT-TYPE SYNTAX INTEGER { copper(1), fiber(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the port type: fiber 1G/100M or copper." ::= { sysPortDescriptionEntry 2 } sysPortDescString OBJECT-TYPE SYNTAX DisplayString(SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the port description." ::= { sysPortDescriptionEntry 3 } sysPortUpLinkTime OBJECT-TYPE SYNTAX DisplayString(SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the port link up time." ::= { sysPortDescriptionEntry 4 } -- end DLINK_METRO_LIKE_GENERAL -- start DLINK_METRO_LIKE_GENERAL sysPortErrTable OBJECT-TYPE SYNTAX SEQUENCE OF SysPortErrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port error table." ::= { companySystem 15 } sysPortErrEntry OBJECT-TYPE SYNTAX SysPortErrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information for the err port of the device." INDEX { sysPortErrPortIndex } ::= { sysPortErrTable 1 } SysPortErrEntry ::= SEQUENCE { sysPortErrPortIndex INTEGER, sysPortErrPortState INTEGER, sysPortErrPortStatus INTEGER, sysPortErrPortReason INTEGER } sysPortErrPortIndex OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the module's port number.(1..Max port number in the module)" ::= { sysPortErrEntry 1 } sysPortErrPortState OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object decides whether the port state is enabled or disabled." ::= { sysPortErrEntry 2 } sysPortErrPortStatus OBJECT-TYPE SYNTAX INTEGER { other(1), err-disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object decides whether the PortStatus is err-disabled." ::= { sysPortErrEntry 3 } sysPortErrPortReason OBJECT-TYPE SYNTAX INTEGER { lbd(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object decides whether the PortStatus is LBD." ::= { sysPortErrEntry 4 } -- end DLINK_METRO_LIKE_GENERAL sysDhcpAutoConfiguration OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates auto config is enabled or disabled." DEFVAL { disable } ::= { companySystem 16 } -- start DLINK_METRO_LIKE_GENERAL sysWebState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for Enabled(1) or Disabled(2) Web state in the system." ::= { companySystem 17 } sysWebPortNumber OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Web Server Port Number." DEFVAL { 80 } ::= { companySystem 18 } sysARPAgingTime OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for ARP aging time." ::= { companySystem 19 } sysMACAgingTime OBJECT-TYPE SYNTAX INTEGER (10..600) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for MAC aging time." ::= { companySystem 20 } baudRateConfiguration OBJECT-TYPE SYNTAX INTEGER { baudrate9600(9600), baudrate19200(19200), baudrate38400(38400), baudrate115200(115200) } MAX-ACCESS read-write STATUS current DESCRIPTION "To set SerialPort baud-rate configuration." ::= { companySystem 21 } autologoutConfiguration OBJECT-TYPE SYNTAX INTEGER { logouttime2mins(120), logouttime5mins(300), logouttime10mins(600), logouttime15mins(900), logouttimenever(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "To set SerialPort auto-logout-time configuration." ::= { companySystem 22 } telnetsettingManagementOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable management Telnetsetting mechanism." ::= { companySystem 23 } telnetUDPPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value is for setting telnet's UDP Port." DEFVAL { 23 } ::= { companySystem 24 } autoRefreshConfiguration OBJECT-TYPE SYNTAX INTEGER { refreshimenever(0), refreshtime10secs(1), refreshtime30secs(2), refreshtime1min(3), refreshtime5mins(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "To set the WEB panel auto refresh timer." ::= { companySystem 25 } floodfdbOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To set enable status for flood fdb." ::= { companySystem 26 } sysContactName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "To set system contact name." ::= { companySystem 27 } -- end DLINK_METRO_LIKE_GENERAL sysDhcpAutoConfigTimeout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "To set dhcp auto config timeout." ::= { companySystem 28 } sysCommandLogging OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To set enable status for CommandLogging." ::= { companySystem 29 } sysSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(1..13)) MAX-ACCESS read-only STATUS current DESCRIPTION "To get the serial number." ::= { companySystem 30 } -- start DLINK_METRO_LIKE_FIRMWARE_INFO_DISPLAY --FirmwareInfo sysVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "The version of firmware information." DEFVAL { "" } ::= { sysFirmwareInfomation 1 } sysSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The size of firmware information." ::= { sysFirmwareInfomation 2 } sysUpdateTime OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Update Time of firmware information." ::= { sysFirmwareInfomation 3 } sysFromIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of firmware information." ::= { sysFirmwareInfomation 4 } sysUser OBJECT-TYPE SYNTAX DisplayString (SIZE(1..9)) MAX-ACCESS read-only STATUS current DESCRIPTION "The user of firmware infomation." ::= { sysFirmwareInfomation 5 } sysType OBJECT-TYPE SYNTAX INTEGER{ console(1), telnet(2), ssh(3), web(4), unknown(-1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of firmware infomation." ::= { sysFirmwareInfomation 6 } -- end DLINK_METRO_LIKE_FIRMWARE_INFO_DISPLAY sysDdp OBJECT IDENTIFIER ::= { companySystem 32 } sysDdpGlobalOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates D-Link discover protocol is enabled or disabled." ::= { sysDdp 1 } sysDdpGeneralReportOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates D-Link discover protocol report is enabled or disabled. This object only can be modified when D-Link discover protocol state is enabled." ::= { sysDdp 2 } sysDdpGeneralReportTimer OBJECT-TYPE SYNTAX INTEGER { time30seconds(30), time60seconds(60), time90seconds(90), time120seconds(120) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates D-Link discover protocol report time period. This object only can be modified when both D-Link discover protocol state and D-Link discover protocol report state are enabled." ::= { sysDdp 3 } sysDdpProtStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF SysDdpProtStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control the port status of D-Link discover protocol." ::= { sysDdp 4 } sysDdpProtStatusEntry OBJECT-TYPE SYNTAX SysDdpProtStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each port D-Link discover protocol status." INDEX { sysDdpProtStatusIndex } ::= { sysDdpProtStatusTable 1 } SysDdpProtStatusEntry ::= SEQUENCE { sysDdpProtStatusIndex Integer32, sysDdpProtStatusControl INTEGER } sysDdpProtStatusIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface index of the port for the configuration in this entry applies." ::= { sysDdpProtStatusEntry 1 } sysDdpProtStatusControl OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures the port status of D-Link discover protocol." ::= { sysDdpProtStatusEntry 2 } sysDhcpAutoImage OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates auto image is enabled or disabled." DEFVAL { disable } ::= { companySystem 34 } sysBootupConfigID OBJECT-TYPE SYNTAX INTEGER (1..2) MAX-ACCESS read-write STATUS current DESCRIPTION "To get/set bootup config ID." ::= { companySystem 35 } sysBootupImage OBJECT-TYPE SYNTAX INTEGER (1..2) MAX-ACCESS read-write STATUS current DESCRIPTION "To get/set bootup Image." ::= { companySystem 36 } -- Port Media Type Table sysPortMediaTypeTable OBJECT-TYPE SYNTAX SEQUENCE OF SysPortMediaTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control the port specific parameters of the device like speed, Vendor name, etc." ::= { companySystem 37 } sysPortMediaTypeEntry OBJECT-TYPE SYNTAX SysPortMediaTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system. Index to the table is the interface index of the port." INDEX { sysPortMediaTypeIndex , sysPortMediaType} ::= { sysPortMediaTypeTable 1 } SysPortMediaTypeEntry ::= SEQUENCE { sysPortMediaTypeIndex Integer32, sysPortMediaType INTEGER, sysPortType INTEGER, sysPortMediaTypeVendorName DisplayString, sysPortMediaTypeOui DisplayString, sysPortMediaTypePn DisplayString, sysPortMediaTypeRev DisplayString, sysPortMediaTypeSn DisplayString, sysPortMediaTypeDateCode DisplayString } sysPortMediaTypeIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface index of the port for the configuration in this entry applies." ::= { sysPortMediaTypeEntry 1 } sysPortMediaType OBJECT-TYPE SYNTAX INTEGER { copper(1), fiber(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the port type: fiber 1G/100M or copper." ::= { sysPortMediaTypeEntry 2 } sysPortType OBJECT-TYPE SYNTAX INTEGER { rate100M (1), rate1000M (2), rate10G (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Configures interface speed." ::= { sysPortMediaTypeEntry 3 } sysPortMediaTypeVendorName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port's VendorName." ::= { sysPortMediaTypeEntry 4 } sysPortMediaTypeOui OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port's Oui." ::= { sysPortMediaTypeEntry 5 } sysPortMediaTypePn OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port's Pn." ::= { sysPortMediaTypeEntry 6 } sysPortMediaTypeRev OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port's Rev." ::= { sysPortMediaTypeEntry 7 } sysPortMediaTypeSn OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port's Sn." ::= { sysPortMediaTypeEntry 8 } sysPortMediaTypeDateCode OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port's DateCode." ::= { sysPortMediaTypeEntry 9 } -- ---------------------------------------------------------- -- The company802Dot3az Groups -- ---------------------------------------------------------- dot3azEEEset OBJECT IDENTIFIER ::= { companydot3azEEE 1 } -- 802Dot3azTable Group --------------------------------------------- -- dot3azTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3azEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control IEEE802.3az EEE settings features of the device." ::= { dot3azEEEset 1 } dot3azEntry OBJECT-TYPE SYNTAX Dot3azEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in IEEE802.3az EEE table for each interface in the system." INDEX { portD3Index } ::= { dot3azTable 1 } Dot3azEntry ::= SEQUENCE { portD3Index Integer32, portD3State INTEGER } portD3Index OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index for which the configuration in this entry applies." ::= { dot3azEntry 1 } portD3State OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2), notsupported (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable / disable port IEEE802.3az EEE admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled." ::= { dot3azEntry 2 } -- ------------------------------------------------------------------------- -- companyIpifGroup -- ------------------------------------------------------------------------- ipv4sysIpAddrCfgMode OBJECT-TYPE SYNTAX INTEGER { manual(1), dynamic(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system." DEFVAL { manual } ::= { companyIpifGroup 1 } ipv4sysIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored." ::= { companyIpifGroup 2 } ipv4sysIpSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored." ::= { companyIpifGroup 3 } ipv4sysGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Gateway" ::= { companyIpifGroup 4 } ipv4dhcpOption12Status OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Status of DHCP Option12" ::= { companyIpifGroup 5 } ipv4dhcpOption12HostName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Host name in DHCP option 12" ::= { companyIpifGroup 6 } -- ---------------------------------------------------------------- -- The multiIFSupportV4V6Info group -- ---------------------------------------------------------------- ipifSupportV4V6Info OBJECT IDENTIFIER ::= { companyIpifGroup 7 } sysIpAddrCfgMode OBJECT-TYPE SYNTAX INTEGER { manual(1), dynamic(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system." DEFVAL { manual } ::= { ipifSupportV4V6Info 1 } sysIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored." ::= { ipifSupportV4V6Info 2 } sysIpSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored." ::= { ipifSupportV4V6Info 3 } sysGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Gateway" ::= { ipifSupportV4V6Info 4 } dhcpOption12Status OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Status of DHCP Option12" ::= { ipifSupportV4V6Info 5 } dhcpOption12HostName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Host name in DHCP option 12" ::= { ipifSupportV4V6Info 6 } ipifName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Description for the interface." ::= { ipifSupportV4V6Info 7 } ipifVLANname OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan name for the interface." ::= { ipifSupportV4V6Info 8 } ipifv6GlobalStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The ID of VLAN that you want this interface to be in. It must be a exist vlan id." ::= { ipifSupportV4V6Info 9 } ipifv6DHCPStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of DHCPv6 that you want this interface to be in. It must be a exist vlan id." ::= { ipifSupportV4V6Info 10 } ipifv6AutolinkloStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The global state of link local that you want this interface to be in. It must be a exist vlan id." ::= { ipifSupportV4V6Info 11 } ipifv6NSRetransmitTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "The NS's retransmit time that you want this interface to be in. It must be a exist vlan id (1~3600)." ::= { ipifSupportV4V6Info 12 } ipifv6DefaultGateway OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-create STATUS current DESCRIPTION "The ipv6 default gateway that you want this interface to be in. It must be a exist vlan id." ::= { ipifSupportV4V6Info 13 } -- --------------------------------------------------------------------- -- --------------------------------------------------------------------- ipifV6AddressTable OBJECT-TYPE SYNTAX SEQUENCE OF IpifV6AddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of interface entries." ::= { ipifSupportV4V6Info 14} ipifV6AddressEntry OBJECT-TYPE SYNTAX IpifV6AddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing management information applicable to a particular interface." INDEX { ipifV6AddressMainIndex, ipifV6AddressIpAddr, ipifV6AddressIpPrefix } ::= { ipifV6AddressTable 1 } IpifV6AddressEntry ::= SEQUENCE { ipifV6AddressMainIndex InterfaceIndex, ipifV6AddressIpAddr Ipv6Address, -- IPv6 Address. ipifV6AddressIpPrefix INTEGER, -- IPv6 Address Prefix. ipifV6AddressIpType INTEGER, -- IP type (Link-local, Global, anycast). ipifV6AddressRowStatus RowStatus -- IPv6 Address entries row status. } ipifV6AddressMainIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of this IPv6 entry." ::= { ipifV6AddressEntry 1 } ipifV6AddressIpAddr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The ip address of this IPv6 entry." DEFVAL { '00000000'H } ::= { ipifV6AddressEntry 2 } ipifV6AddressIpPrefix OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The ip prefix of this IPv6 entry." ::= { ipifV6AddressEntry 3 } ipifV6AddressIpType OBJECT-TYPE SYNTAX INTEGER { unicast(1), anycast(2), linklocal(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The ip type of this IPv6 entry." ::= { ipifV6AddressEntry 4 } ipifV6AddressRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of an entry in the Multi Interface Table. Only a subset of the rowstatus variables (active, createAndWait, destroy) are available." ::= { ipifV6AddressEntry 5 } -- --------------------------------------------------------------------- -- --------------------------------------------------------------------- ipv4sysIprouteGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IProute Gateway of the system." ::= { companyIpifGroup 8 } ipv4sysIprouteHops OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "IProute Hops of the system." ::= { companyIpifGroup 9 } -- ------------------------------------------------------------------------- -- companyTftpGroup -- ------------------------------------------------------------------------- tftpFwServerIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The TFTP server's IP address is used to upload or download firmware." ::= { companyTftpGroup 1 } tftpFwImageFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Configure firmware filename to download." ::= { companyTftpGroup 2 } tftpFwTftpOperation OBJECT-TYPE SYNTAX INTEGER { none(0), download(1), upload(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName." ::= { companyTftpGroup 3 } tftpFwTftpOperationStatus OBJECT-TYPE SYNTAX INTEGER { none(0), success(1), fail(2), progressing(3), transmit(4) } MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The tftp operation status represent firmware backup or upgrade status." ::= { companyTftpGroup 4 } tftpCfgServerIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The TFTP server's IP address is used to upload or download configuration file." ::= { companyTftpGroup 5 } tftpConfigFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The configuration filename is used to store or retrieve config from the tftp server." ::= { companyTftpGroup 6 } tftpConfigTftpOperation OBJECT-TYPE SYNTAX INTEGER { download(1), upload(2), progressing(3) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName." ::= { companyTftpGroup 7 } tftpConfigTftpOperationStatus OBJECT-TYPE SYNTAX INTEGER { none(0), success(1), fail(2), progressing(3) } MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The tftp operation status represent configuration file backup or restore status." ::= { companyTftpGroup 8 } tftpFwTargetGroup OBJECT IDENTIFIER ::= { companyTftpGroup 9 } tftpFwTargetServerIpAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The TFTP server's IP address is used to upload or download firmware." ::= { tftpFwTargetGroup 1 } tftpFwTargetServerIpType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of IP interface." ::= { tftpFwTargetGroup 2 } tftpFwTargetInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the interface name when the tftpFwTargetServerIpAddress is linklocal address." ::= { tftpFwTargetGroup 3 } tftpFwTargetImageFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Configure firmware filename to download." ::= { tftpFwTargetGroup 4 } tftpFwTargetTftpOperation OBJECT-TYPE SYNTAX INTEGER { none(0), download(1), upload(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName." ::= { tftpFwTargetGroup 5 } tftpFwTargetTftpOperationStatus OBJECT-TYPE SYNTAX INTEGER { none(0), success(1), fail(2), progressing(3), transmit(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The tftp operation status represent firmware backup or upgrade status." ::= { tftpFwTargetGroup 6 } tftpCfgTargetGroup OBJECT IDENTIFIER ::= { companyTftpGroup 10 } tftpCfgTargetServerIpAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The TFTP server's IP address is used to upload or download configuration file." ::= { tftpCfgTargetGroup 1 } tftpCfgTargetServerIpType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of IP interface." ::= { tftpCfgTargetGroup 2 } tftpCfgTargetInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the interface name when the tftpCfgTargetServerIpAddress is linklocal address." ::= { tftpCfgTargetGroup 3 } tftpCfgTargetImageFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "The configuration filename is used to store or retrieve config from the tftp server." ::= { tftpCfgTargetGroup 4 } tftpCfgTargetTftpOperation OBJECT-TYPE SYNTAX INTEGER { download(1), upload(2), progressing(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName." ::= { tftpCfgTargetGroup 5 } tftpCfgTargetTftpOperationStatus OBJECT-TYPE SYNTAX INTEGER { none(0), success(1), fail(2), progressing(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The tftp operation status represent configuration file backup or restore status." ::= { tftpCfgTargetGroup 6 } tftpCfgTargetConfigID OBJECT-TYPE SYNTAX INTEGER { config1(1), config2(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName." ::= { tftpCfgTargetGroup 7 } -- ------------------------------------------------------------------------- -- company Extension MIB, Miscellaneous Information -- ------------------------------------------------------------------------- miscReset OBJECT-TYPE SYNTAX INTEGER { reset(1), noop(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing." ::= { companyMiscGroup 2 } miscStatisticsReset OBJECT-TYPE SYNTAX INTEGER { reset(1), noop(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Resets the units statistics. A (1) resets the statistics count, a (2) does nothing." ::= { companyMiscGroup 3 } -- ---------------------------------------------------------- -- The companySecurity Groups -- ---------------------------------------------------------- securityIpMacPortBinding OBJECT IDENTIFIER ::= { companySecurity 10 } -- IpMacPortBinding Group --------------------------------------------- -- impbSettingTable OBJECT-TYPE SYNTAX SEQUENCE OF ImpbSettingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control IP-MAC-Port Binding Setting features of the device." ::= { securityIpMacPortBinding 1 } impbSettingEntry OBJECT-TYPE SYNTAX ImpbSettingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in IP-MAC-Port Binding Setting table for each interface in the system." INDEX { impbPortIndex } ::= { impbSettingTable 1 } ImpbSettingEntry ::= SEQUENCE { impbPortIndex INTEGER, impbPortState INTEGER, impbPortDHCPSnoopingState INTEGER, impbPortArpInspectionState INTEGER, impbPortIpInspectionState INTEGER, impbPortAllowZeroIPState INTEGER, impbPortForwardDHCPPktState INTEGER, impbPortDHCPMaxEntryIPv4 Integer32, impbPortDHCPMaxEntryIPv6 Integer32, impbPortNDInspectionState INTEGER, impbPortProtocolState INTEGER, impbPortDHCPv4SetVlanList OCTET STRING, impbPortDHCPv4VlanList1k OCTET STRING, impbPortDHCPv4VlanList2k OCTET STRING, impbPortDHCPv4VlanList3k OCTET STRING, impbPortDHCPv4VlanList4k OCTET STRING, impbPortDHCPv6SetVlanList OCTET STRING, impbPortDHCPv6VlanList1k OCTET STRING, impbPortDHCPv6VlanList2k OCTET STRING, impbPortDHCPv6VlanList3k OCTET STRING, impbPortDHCPv6VlanList4k OCTET STRING } impbPortIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports." ::= { impbSettingEntry 1 } impbPortState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Disable / enable IP-MAC-Port Binding admin state for the interface." ::= { impbSettingEntry 2 } impbPortDHCPSnoopingState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Disable / enable IP-MAC-Port Binding DHCP snooping state for the interface." ::= { impbSettingEntry 4 } impbPortArpInspectionState OBJECT-TYPE SYNTAX INTEGER { disabled (0), strict (1), loose (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set IP-MAC-Port Binding ARP Inspection state for the interface." ::= { impbSettingEntry 5 } impbPortIpInspectionState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set IP-MAC-Port Binding IP Inspection state for the interface." ::= { impbSettingEntry 6 } impbPortAllowZeroIPState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Disable / enable IP-MAC-Port Binding Allow-Zero-IP state for the interface." ::= { impbSettingEntry 7 } impbPortForwardDHCPPktState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Disable / enable IP-MAC-Port Binding Forward-DHCP-Packet state for the interface." ::= { impbSettingEntry 8 } impbPortDHCPMaxEntryIPv4 OBJECT-TYPE SYNTAX Integer32 (0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "Set the maximum number of IPv4 entries that can be learned for the interface." ::= { impbSettingEntry 9 } impbPortDHCPMaxEntryIPv6 OBJECT-TYPE SYNTAX Integer32 (0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "Set the maximum number of IPv6 entries that can be learned for the interface." ::= { impbSettingEntry 10 } impbPortNDInspectionState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set IP-MAC-Port Binding ND Inspection state for the interface." ::= { impbSettingEntry 11 } impbPortProtocolState OBJECT-TYPE SYNTAX INTEGER { ipv4 (0), ipv6 (1), all (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set IP-MAC-Port Binding protocol state for the interface." ::= { impbSettingEntry 12 } impbPortDHCPv4SetVlanList OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to map for this Instance. If the VlanId to Instance Mapping has to be known then any one of the VlanMapped object should be used.If a vlan is already mapped to this Instance, it may not be mapped again. This object is used only for SET operation. GET Operation returns null values." ::= { impbSettingEntry 13 } impbPortDHCPv4VlanList1k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCP snooping, the bit corresponding to that VLAN is set to '1'. " ::= { impbSettingEntry 14 } impbPortDHCPv4VlanList2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1025 through 2048. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCPv4 snooping, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4094." ::= { impbSettingEntry 15 } impbPortDHCPv4VlanList3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2049 through 3072. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCPv4 snooping the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4094." ::= { impbSettingEntry 16 } impbPortDHCPv4VlanList4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3073 through 4094. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCPv4 snooping, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4094." ::= { impbSettingEntry 17 } impbPortDHCPv6SetVlanList OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to map for this Instance. If the VlanId to Instance Mapping has to be known then any one of the VlanMapped object should be used.If a vlan is already mapped to this Instance, it may not be mapped again. This object is used only for SET operation. GET Operation returns null values." ::= { impbSettingEntry 18 } impbPortDHCPv6VlanList1k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCP snooping, the bit corresponding to that VLAN is set to '1'. " ::= { impbSettingEntry 19 } impbPortDHCPv6VlanList2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1025 through 2048. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCPv6 snooping, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4094." ::= { impbSettingEntry 20 } impbPortDHCPv6VlanList3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2049 through 3072. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCPv6 snooping the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4094." ::= { impbSettingEntry 21 } impbPortDHCPv6VlanList4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3073 through 4094. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCPv6 snooping, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4094." ::= { impbSettingEntry 22 } impbAutoScanTable OBJECT-TYPE SYNTAX SEQUENCE OF ImpbAutoScanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control auto scan features of the device." ::= { securityIpMacPortBinding 2 } impbAutoScanEntry OBJECT-TYPE SYNTAX ImpbAutoScanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in auto scan table for each interface in the system." INDEX { impbAutoScanMacAddress, impbAutoScanPort, impbAutoScanIpAddress} ::= { impbAutoScanTable 1 } ImpbAutoScanEntry ::= SEQUENCE { impbAutoScanMacAddress MacAddress, impbAutoScanPort Integer32, impbAutoScanIpAddress DisplayString, impbAutoScanVlanId Integer32, impbAutoScanBinding INTEGER } impbAutoScanMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the auto scan entry." ::= { impbAutoScanEntry 1 } impbAutoScanPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the auto scan entry." ::= { impbAutoScanEntry 2 } impbAutoScanIpAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address associated of the auto scan entry." DEFVAL { '00000000'H } ::= { impbAutoScanEntry 3 } impbAutoScanVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the auto scan entry." ::= { impbAutoScanEntry 4 } impbAutoScanBinding OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Disable / enable IP-MAC-Port Binding for the entry." ::= { impbAutoScanEntry 5 } impbBindingListTable OBJECT-TYPE SYNTAX SEQUENCE OF ImpbBindingListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control Manual IP-MAC-Port Binding white list features of the device." ::= { securityIpMacPortBinding 3 } impbBindingListEntry OBJECT-TYPE SYNTAX ImpbBindingListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in Manual IP-MAC-Port Binding white list table for each interface in the system." INDEX { impbBindingListIpAddress, impbBindingListMacAddress } ::= { impbBindingListTable 1 } ImpbBindingListEntry ::= SEQUENCE { impbBindingListIpAddress DisplayString, impbBindingListMacAddress MacAddress, impbBindingListPort Integer32, impbBindingListRowStatus RowStatus } impbBindingListIpAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address associated of the Manual IP-MAC-PORT Binding white list entry." DEFVAL { '00000000'H } ::= { impbBindingListEntry 1 } impbBindingListMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the Manual IP-MAC-PORT Binding white list entry." ::= { impbBindingListEntry 2 } impbBindingListPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The port number of the Manual IP-MAC-PORT Binding white list entry." ::= { impbBindingListEntry 3 } impbBindingListRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of a row in impbBindingListTable. By setting this object, new entries can be created in impbBindingListTable and existing entries can be removed from impbBindingListTable. It can be used as specified in the SNMP v2 standard." ::= { impbBindingListEntry 4 } impbBlockListTable OBJECT-TYPE SYNTAX SEQUENCE OF ImpbBlockListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control IP-MAC-Port Binding black list of the device." ::= { securityIpMacPortBinding 4 } impbBlockListEntry OBJECT-TYPE SYNTAX ImpbBlockListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in Manual IP-MAC-Port Binding black list table for each interface in the system." INDEX { impbBlockListMacAddress, impbBlockListVlanId, impbBlockListPort } ::= { impbBlockListTable 1 } ImpbBlockListEntry ::= SEQUENCE { impbBlockListMacAddress MacAddress, impbBlockListVlanId Integer32, impbBlockListPort Integer32, impbBlockListIpAddress DisplayString, impbBlockListStatus INTEGER } impbBlockListMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the IP-MAC-PORT Binding black list entry." ::= { impbBlockListEntry 1 } impbBlockListVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the IP-MAC-PORT Binding black list entry." ::= { impbBlockListEntry 2 } impbBlockListPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the IP-MAC-PORT Binding black list entry." ::= { impbBlockListEntry 3 } impbBlockListIpAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address associated of the IP-MAC-PORT Binding black list entry." DEFVAL { '00000000'H } ::= { impbBlockListEntry 4 } impbBlockListStatus OBJECT-TYPE SYNTAX INTEGER { nothing (0), deleted (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "nothing/delete IP-MAC-Port Binding for the interface." ::= { impbBlockListEntry 5 } impbAutoScanIpAddressFrom OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The begin for IP address associated of the IP-MAC-PORT Binding auto scan entry." DEFVAL { '00000000'H } ::= { securityIpMacPortBinding 5 } impbAutoScanIpAddressTo OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The end for IP address associated of the IP-MAC-PORT Binding auto scan entry." DEFVAL { '00000000'H } ::= { securityIpMacPortBinding 6 } impbAutoScanStatus OBJECT-TYPE SYNTAX INTEGER { nothing (0), scan (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Nothing / scan IP-MAC-Port Binding auto scan for the interface." ::= { securityIpMacPortBinding 7 } impbDhcpSnoopingTable OBJECT-TYPE SYNTAX SEQUENCE OF ImpbDhcpSnoopingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to display DHCP snooping entries of the device." ::= { securityIpMacPortBinding 8 } impbDhcpSnoopingEntry OBJECT-TYPE SYNTAX ImpbDhcpSnoopingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in DHCP snooping table for each interface in the system." INDEX { impbDhcpSnoopingMacAddress, impbDhcpSnoopingIpAddress } ::= { impbDhcpSnoopingTable 1 } ImpbDhcpSnoopingEntry ::= SEQUENCE { impbDhcpSnoopingMacAddress MacAddress, impbDhcpSnoopingIpAddress Ipv6Address, impbDhcpSnoopingLeaseTime Integer32, impbDhcpSnoopingPort Integer32 } impbDhcpSnoopingMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the DHCP snooping entry." ::= { impbDhcpSnoopingEntry 1 } impbDhcpSnoopingIpAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address associated of the DHCP snooping entry." DEFVAL { '00000000'H } ::= { impbDhcpSnoopingEntry 2 } impbDhcpSnoopingLeaseTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The lease time associated of the DHCP snooping entry." ::= { impbDhcpSnoopingEntry 3 } impbDhcpSnoopingPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port number associated of the DHCP snooping entry." ::= { impbDhcpSnoopingEntry 4 } impbRoamingState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Disable / enable IP-MAC-Port Binding roaming state." ::= { securityIpMacPortBinding 9 } impbVlanModeState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Disable / enable IP-MAC-Port Binding vlan mode state." ::= { securityIpMacPortBinding 10 } impbVlanModeVlanList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "IP-MAC-Port Binding vlan mode VID list." ::= { securityIpMacPortBinding 11 } impbLogState OBJECT-TYPE SYNTAX INTEGER { disabled (0), ipv4 (1), ipv6 (2), all (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configure IP-MAC-Port Binding log state." ::= { securityIpMacPortBinding 12 } impbDHCPv6PrefixDelegationSnoopState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configure DHCPv6 PD snooping state." ::= { securityIpMacPortBinding 13 } impbBindingtraplog OBJECT-TYPE SYNTAX INTEGER { disabled (2), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling topology change event trap in the system." ::= { securityIpMacPortBinding 14 } impbBindingtrap OBJECT IDENTIFIER ::= { securityIpMacPortBinding 15 } impbBindingtrapsign NOTIFICATION-TYPE STATUS current DESCRIPTION "The object is for IMPB trap sign in the system." ::= {impbBindingtrap 1 } impbAutoScanCurrentStatus OBJECT-TYPE SYNTAX INTEGER { stop (0), scanning (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Show Auto scan status" ::= { securityIpMacPortBinding 16 } -- ---------------------------------------------------------------- -- The STP Bridge Global -- ---------------------------------------------------------------- stpBridgeGlobal OBJECT IDENTIFIER ::= { companySTP 1 } stpModuleStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start." ::= { stpBridgeGlobal 1 } stpProtocolVersion OBJECT-TYPE SYNTAX INTEGER { stp(1), rstp(2), mstp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning Tree Protocol specified in IEEE 802.1w and 'mstp(3)' indicates the Multiple Spanning Tree Protocol Specified in IEEE 802.1s." DEFVAL { rstp } ::= { stpBridgeGlobal 2 } stpBridgePriority OBJECT-TYPE SYNTAX Integer32 (0..61440) MAX-ACCESS read-write STATUS current DESCRIPTION "The Value of the writable portion of the Bridge Identifier comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096." DEFVAL {32768} ::= { stpBridgeGlobal 3 } stpTxHoldCount OBJECT-TYPE SYNTAX Integer32 (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The value used by the Port Transmit state machine to limit the maximum transmission rate." DEFVAL { 3 } ::= { stpBridgeGlobal 4 } stpBridgeMaxAge OBJECT-TYPE SYNTAX Timeout (600..4000) MAX-ACCESS read-write STATUS current DESCRIPTION "The value that all bridges use for MaxAge when this bridge is acting as the root. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds." DEFVAL {2000} ::= { stpBridgeGlobal 5 } stpBridgeHelloTime OBJECT-TYPE SYNTAX Timeout (100..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second." ::= { stpBridgeGlobal 6 } stpBridgeForwardDelay OBJECT-TYPE SYNTAX Timeout (400..3000) MAX-ACCESS read-write STATUS current DESCRIPTION "The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D specifies that the range for this parameter is related to the value of BridgeMaxAge. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds." DEFVAL {1500} ::= { stpBridgeGlobal 7 } stpFowardBPDU OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling forward BPDU." ::= {stpBridgeGlobal 8 } stpRootBridge OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge identifier of the Root of the common spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the CIST Root Identifier parameter in all Configuration Bridge PDUs originated by this node." ::= { stpBridgeGlobal 9 } stpRootCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Cost of the path to the CIST Root as seen from this bridge." ::= { stpBridgeGlobal 10 } stpMaxAge OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using." ::= { stpBridgeGlobal 11 } stpForwardDelay OBJECT-TYPE SYNTAX Timeout MAX-ACCESS read-only STATUS current DESCRIPTION "This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in a particular state before moving to the next state." ::= { stpBridgeGlobal 12 } stpRootPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Port Number of the Port which offers the lowest path cost from this bridge to the CIST Root Bridge." ::= { stpBridgeGlobal 13 } stpTopologyChangeTrapStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling topology change event trap in the system." DEFVAL { disabled } ::= { stpBridgeGlobal 14 } stpNewRootTrapStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling new root event trap in the system." DEFVAL { disabled } ::= { stpBridgeGlobal 15 } stpNewRootTraps OBJECT IDENTIFIER ::= { stpBridgeGlobal 16 } brgAddress NOTIFICATION-TYPE STATUS current DESCRIPTION "The MAC address used by this bridge when it must be referred to in a unique fashion." ::= { stpNewRootTraps 1 } oldDesignatedRoot NOTIFICATION-TYPE STATUS current DESCRIPTION "The bridge identifier of the old root of the spanning tree instance as determined by the Spanning Tree Protocol as executed by this node." ::= { stpNewRootTraps 2 } mstiBridgeRegionalRoot NOTIFICATION-TYPE STATUS current DESCRIPTION "MSTI Regional Root Identifier value for the Instance." ::= { stpNewRootTraps 3 } -- ------------------------------------- -- The Spanning Tree Port Table -- ------------------------------------- stpPortTable OBJECT-TYPE SYNTAX SEQUENCE OF StpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains port-specific information for the Spanning Tree Protocol." ::= { companySTP 2 } stpPortEntry OBJECT-TYPE SYNTAX StpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information maintained by every port about the Spanning Tree Protocol state for that port." INDEX { stpPort } ::= { stpPortTable 1 } StpPortEntry ::= SEQUENCE { stpPort INTEGER, stpPortStatus INTEGER, stpPortPriority INTEGER, stpAdminPortPathCost INTEGER, stpPortPathCost INTEGER, stpPortProtocolMigration TruthValue, stpPortEdge INTEGER, stpPortAdminP2P INTEGER, stpPortRestrictedRole TruthValue, stpPortRestrictedTCN TruthValue, stpPortHelloTime Timeout, stpPortState INTEGER, stpPortFowardBPDU INTEGER } stpPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The Port number of the port for which this entry contains spanning tree information." ::= { stpPortEntry 1 } stpPortStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Current state of the Port which can be changed to either Disabled or Enabled for ALL spanning tree instances. Setting this object will override the port's status in any of the MSTI contexts" ::= { stpPortEntry 2 } stpPortPriority OBJECT-TYPE SYNTAX INTEGER (0..240) MAX-ACCESS read-write STATUS current DESCRIPTION "The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting the CistPortPriority value. The values that are set for Port Priority must be in steps of 16." DEFVAL {128} ::= { stpPortEntry 3 } stpAdminPortPathCost OBJECT-TYPE SYNTAX INTEGER (0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automatically calculated default Path Cost value to the ohter object stpPortPathCost. If the default Path Cost is being used,this object returns '0' when read." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 4 } stpPortPathCost OBJECT-TYPE SYNTAX INTEGER (1..200000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the CIST Root which include this port." ::= { stpPortEntry 5 } stpPortProtocolMigration OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the Protocol migration state of this Port. When operating in RSTP/MSTP (version >= 2) mode, writing TRUE(1) to this object forces this port to transmit MSTP BPDUs without instance information. Any other operation on this object has no effect and it always returns FALSE(2) when read." ::= { stpPortEntry 6 } stpPortEdge OBJECT-TYPE SYNTAX INTEGER { true(1), false(0), auto(2) } MAX-ACCESS read-write STATUS current DESCRIPTION " This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled." ::= { stpPortEntry 7 } stpPortAdminP2P OBJECT-TYPE SYNTAX INTEGER { forceTrue(0), forceFalse(1), auto(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means." ::= { stpPortEntry 8 } stpPortRestrictedRole OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected. This parameter should be FALSE by default. If set it can cause lack of spanning tree connectivity. It is set by a network administrator to prevent bridges external to a core region of the network influencing the spanning tree active topology, possibly because those bridges are not under the full control of the administrator. This administrator configuration is also known as 'Root Guard'." ::= {stpPortEntry 9} stpPortRestrictedTCN OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause temporary loss of connectivity after changes in a spanning trees active topology as a result of persistent incorrectly learnt station location information. It is set by a network administrator to prevent bridges external to a core region of the network causing address flushing in that region, possibly because those bridges are not under the full control of the administrator or MAC_Operational for the attached LANs transitions frequently." ::= {stpPortEntry 10} stpPortHelloTime OBJECT-TYPE SYNTAX Timeout (100..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second." ::= { stpPortEntry 11 } stpPortState OBJECT-TYPE SYNTAX INTEGER { disabled (1), discarding (2), learning (4), forwarding (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current state of the Port as defined by the Common spanning tree protocol." ::= { stpPortEntry 12 } stpPortFowardBPDU OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling forward BPDU." REFERENCE "IEEE 802.1D-2004" ::= { stpPortEntry 13 } -- ---------------------------------------------------------------- -- The MST Configuration Identification -- ---------------------------------------------------------------- mstConfigurationIdentification OBJECT IDENTIFIER ::= { companySTP 3 } mstiConfigurationName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Name for the Region's configuration. By Default Region Name will be equal to the Bridge Mac Address." ::= { mstConfigurationIdentification 1 } mstiRevisionLevel OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Version of the MST Region." ::= { mstConfigurationIdentification 2 } -- ----------------------------------------------------------------- -- Future Mst VlanId to Instance Mapping Table : CIST -- ----------------------------------------------------------------- mstCistVlanMapped OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'." ::= { mstConfigurationIdentification 3 } mstCistVlanMapped2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095." ::= { mstConfigurationIdentification 4 } mstCistVlanMapped3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095." ::= { mstConfigurationIdentification 5 } mstCistVlanMapped4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095." ::= { mstConfigurationIdentification 6 } -- ----------------------------------------------------------------- -- Future Mst VlanId to Instance Mapping Table : MSTI -- ----------------------------------------------------------------- mstVlanMstiMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF MstVlanMstiMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry for each instance of MSTP. This table maintains context ID as one more index to support Multiple Instances." ::= { mstConfigurationIdentification 7 } mstVlanMstiMappingEntry OBJECT-TYPE SYNTAX MstVlanMstiMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row containing the status of the MSTP instance." INDEX { mstInstanceIndex } ::= { mstVlanMstiMappingTable 1 } MstVlanMstiMappingEntry ::= SEQUENCE { mstInstanceIndex Integer32, mstSetVlanList OCTET STRING, mstResetVlanList OCTET STRING, mstInstanceVlanMapped OCTET STRING, mstInstanceVlanMapped2k OCTET STRING, mstInstanceVlanMapped3k OCTET STRING, mstInstanceVlanMapped4k OCTET STRING } mstInstanceIndex OBJECT-TYPE SYNTAX Integer32 (1..15) MAX-ACCESS read-only STATUS current DESCRIPTION "An arbitrary integer within the range from 1 to the value of Max Instance Number that uniquely identifies an instance." ::= { mstVlanMstiMappingEntry 1 } mstSetVlanList OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to map for this Instance. If the VlanId to Instance Mapping has to be known then any one of the VlanMapped object should be used.If a vlan is already mapped to this Instance, it may not be mapped again. This object is used only for SET operation. GET Operation returns null values." ::= { mstVlanMstiMappingEntry 2 } mstResetVlanList OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to unmap from this Instance. A vlan may not be unmapped from this instance if it is not already mapped to this Instance. This object is used only for SET operation.GET Operation returns null values." ::= { mstVlanMstiMappingEntry 3 } mstInstanceVlanMapped OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'." ::= { mstVlanMstiMappingEntry 4 } mstInstanceVlanMapped2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095." ::= { mstVlanMstiMappingEntry 5 } mstInstanceVlanMapped3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095." ::= { mstVlanMstiMappingEntry 6 } mstInstanceVlanMapped4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095." ::= { mstVlanMstiMappingEntry 7 } -- ----------------------------------------------------------------- -- Mst Multiple Spanning Tree Instance Bridge Table -- ----------------------------------------------------------------- stpInstance OBJECT IDENTIFIER ::= { companySTP 4 } -- ----------------------------------------------------------------- -- Mst Multiple Spanning Tree Instance Bridge Table : CIST -- ----------------------------------------------------------------- mstCistBridgePriority OBJECT-TYPE SYNTAX Integer32 (0..61440) MAX-ACCESS read-write STATUS current DESCRIPTION "The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096." DEFVAL {32768} ::= { stpInstance 1 } mstCistStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start." ::= { stpInstance 2 } -- ----------------------------------------------------------------- -- Mst Multiple Spanning Tree Instance Bridge Table : MSTI -- ----------------------------------------------------------------- mstMstiBridgeTable OBJECT-TYPE SYNTAX SEQUENCE OF MstMstiBridgeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing Bridge Information specific to Spanning Tree Instance. This table maintains context ID as one more index to support Multiple Instances." ::= { stpInstance 3 } mstMstiBridgeEntry OBJECT-TYPE SYNTAX MstMstiBridgeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry indicating the Bridge Information." INDEX { mstMstiInstanceIndex } ::= { mstMstiBridgeTable 1 } MstMstiBridgeEntry ::= SEQUENCE { mstMstiInstanceIndex Integer32, mstMstiBridgePriority Integer32, mstMstiStatus INTEGER } mstMstiInstanceIndex OBJECT-TYPE SYNTAX Integer32 (1..15) MAX-ACCESS read-only STATUS current DESCRIPTION "Spanning Tree Instance to which the information belongs." ::= { mstMstiBridgeEntry 1 } mstMstiBridgePriority OBJECT-TYPE SYNTAX Integer32 (0..61440) MAX-ACCESS read-write STATUS current DESCRIPTION "The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096." DEFVAL {32768} ::= { mstMstiBridgeEntry 2 } mstMstiStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start." ::= { mstMstiBridgeEntry 3 } -- ----------------------------------------------------------------- -- Mst Multiple Spanning Tree Instance Bridge Table -- ----------------------------------------------------------------- stpInstancePortTable OBJECT IDENTIFIER ::= { companySTP 5 } -- ----------------------------------------------------------------- -- Mst Multiple Spanning Tree Instance Port Table : CIST -- ----------------------------------------------------------------- mstCistPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MstCistPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Common Spanning Tree Port Information." ::= { stpInstancePortTable 1 } mstCistPortEntry OBJECT-TYPE SYNTAX MstCistPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information maintained by every port for Common Spanning tree." INDEX { mstCistPort } ::= { mstCistPortTable 1 } MstCistPortEntry ::= SEQUENCE { mstCistPort Integer32, mstCistPortDesignatedBridge BridgeId, mstCistPortAdminPathCost Integer32, mstCistPortPathCost Integer32, mstCistPortPriority Integer32, mstCistForcePortState INTEGER, mstCistCurrentPortRole INTEGER } mstCistPort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Port number of the port for which this entry contains spanning tree information." ::= { mstCistPortEntry 1 } mstCistPortDesignatedBridge OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment." ::= { mstCistPortEntry 2 } mstCistPortAdminPathCost OBJECT-TYPE SYNTAX Integer32 (0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the MSTI Root which include this port." ::= { mstCistPortEntry 3 } mstCistPortPathCost OBJECT-TYPE SYNTAX Integer32 (1..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the MSTI Root which include this port." ::= { mstCistPortEntry 4 } mstCistPortPriority OBJECT-TYPE SYNTAX Integer32 (0..240) MAX-ACCESS read-write STATUS current DESCRIPTION "The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16." DEFVAL {128} ::= { mstCistPortEntry 5 } mstCistForcePortState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' for this port" ::= { mstCistPortEntry 6 } mstCistCurrentPortRole OBJECT-TYPE SYNTAX INTEGER { disabled(0), alternate(1), backup(2), root(3), designated(4), master(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current Port Role of the port for this spanning tree instance." ::= { mstCistPortEntry 7 } -- ----------------------------------------------------------------- -- Mst Multiple Spanning Tree Instance Port Table : MSTI -- ----------------------------------------------------------------- mstMstiPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MstMstiPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Spanning Tree Instance Specific Port Information." ::= { stpInstancePortTable 2 } mstMstiPortEntry OBJECT-TYPE SYNTAX MstMstiPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information maintained by every port for each and every spanning tree instance." INDEX { mstMstiPort, mstInstanceIndex } ::= { mstMstiPortTable 1 } MstMstiPortEntry ::= SEQUENCE { mstMstiPort Integer32, mstMstiPortDesignatedBridge BridgeId, mstMstiPortAdminPathCost Integer32, mstMstiPortPathCost Integer32, mstMstiPortPriority Integer32, mstMstiForcePortState INTEGER, mstMstiCurrentPortRole INTEGER } mstMstiPort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Port number of the port for which this entry contains spanning tree information." ::= { mstMstiPortEntry 1 } mstMstiPortDesignatedBridge OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment." ::= { mstMstiPortEntry 2 } mstMstiPortAdminPathCost OBJECT-TYPE SYNTAX Integer32 (0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the MSTI Root which include this port." ::= { mstMstiPortEntry 3 } mstMstiPortPathCost OBJECT-TYPE SYNTAX Integer32 (1..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the MSTI Root which include this port." ::= { mstMstiPortEntry 4 } mstMstiPortPriority OBJECT-TYPE SYNTAX Integer32 (0..240) MAX-ACCESS read-write STATUS current DESCRIPTION "The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16." DEFVAL {128} ::= { mstMstiPortEntry 5 } mstMstiForcePortState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' for this port" ::= { mstMstiPortEntry 6 } mstMstiCurrentPortRole OBJECT-TYPE SYNTAX INTEGER { disabled(0), alternate(1), backup(2), root(3), designated(4), master(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current Port Role of the port for this spanning tree instance." ::= { mstMstiPortEntry 7 } -- ------------------------------------------------------------------ -- The Static Multicast Group -- ------------------------------------------------------------------ staticMcastTable OBJECT-TYPE SYNTAX SEQUENCE OF StaticMcastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the Static MACs" ::= { companyStaticMcast 1 } staticMcastEntry OBJECT-TYPE SYNTAX StaticMcastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Static MAC entry containing the mac and forwarding port." INDEX { staticMcastVlanID, staticMcastMac, staticMcastEgressPorts, staticMcastIpAddr} ::= { staticMcastTable 1 } StaticMcastEntry ::= SEQUENCE { staticMcastVlanID INTEGER, staticMcastMac MacAddress, staticMcastEgressPorts PortList, staticMcastIpAddr IpAddress, staticMcastStatus RowStatus } staticMcastVlanID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the static MAC entry." ::= { staticMcastEntry 1 } staticMcastMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the static MAC entry." ::= { staticMcastEntry 2 } staticMcastEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of any dynamic information e.g. from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastForbiddenEgressPorts. The default value of this object is a string of ones of appropriate length." REFERENCE "IEEE 802.1Q/D11 Section 12.7.7.3, 11.2.3.2.3" ::= { staticMcastEntry 3 } staticMcastIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Static Multicast IP Address." ::= { staticMcastEntry 4 } staticMcastStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of an entry in the Static Mcast Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available." ::= { staticMcastEntry 5 } -- ---------------------------------------------------------- -- The 802.1Q VLAN Groups -- ---------------------------------------------------------- dot1qVlanManagementOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable management VLAN mechanism." ::= { companyDot1qVlanGroup 2 } dot1qVlanManagementid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The management VLAN ID, which will allow to forward packets of that VLAN to CPU." DEFVAL { 1 } ::= { companyDot1qVlanGroup 3 } dot1qVlanAsyOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable IEEE 802.1Q Asymmetric VLAN" ::= { companyDot1qVlanGroup 5 } -- ------------------------------------------------------------- -- The VLAN Database -- ------------------------------------------------------------- dot1qVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset." ::= { companyDot1qVlanGroup 6 } dot1qVlanEntry OBJECT-TYPE SYNTAX Dot1qVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information for a VLAN configured into the device by (local or network) management." INDEX { dot1qVlanName } ::= { dot1qVlanTable 1 } Dot1qVlanEntry ::= SEQUENCE { dot1qVlanName SnmpAdminString, dot1qVlanEgressPorts PortList, dot1qVlanForbiddenPorts PortList, dot1qVlanUntaggedPorts PortList, dot1qVlanAdvertisementStatus INTEGER, dot1qVlanRowStatus RowStatus } dot1qVlanName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..20)) MAX-ACCESS read-create STATUS current DESCRIPTION "An administratively assigned string, which may be used to identify the VLAN." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanEntry 1 } dot1qVlanEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed." REFERENCE "IEEE 802.1Q/D11 Section 12.7.7.3, 11.2.3.2.3" ::= { dot1qVlanEntry 2 } dot1qVlanForbiddenPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be included or excluded affect the per-port per-VLAN Registrar control for Registration Forbidden for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanEgressPorts. The default value of this object is a string of zeros of appropriate length, excluding all ports from the forbidden set." REFERENCE "IEEE 802.1Q/D11 Section 12.7.7.3, 11.2.3.2.3" ::= { dot1qVlanEntry 3 } dot1qVlanUntaggedPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set then it will reject the set operation with an error. An example might be if a manager attempts to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanEntry 4 } dot1qVlanAdvertisementStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/Disable Advertisement Status of the IEEE 802.1Q VLAN." ::= { dot1qVlanEntry 5 } dot1qVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanTable. It can be used as specified in the SNMP v2 standard." ::= { dot1qVlanEntry 6 } -- ------------------------------------------------------------- -- The VLAN Ungister Multicast Filter Table -- ------------------------------------------------------------- dot1qVlanUngisterMCFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qVlanUngisterMCFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the list of ports through which a router, in a particular VLAN is reachable." ::= { companyDot1qVlanGroup 8 } dot1qVlanUngisterMCFilterEntry OBJECT-TYPE SYNTAX Dot1qVlanUngisterMCFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of multicast filter mode information for each VLAN ID." INDEX { dot1qVlanUngisterMCFilterVlanId } ::= { dot1qVlanUngisterMCFilterTable 1 } Dot1qVlanUngisterMCFilterEntry ::= SEQUENCE { dot1qVlanUngisterMCFilterVlanId Integer32, dot1qVlanUngisterMCFiltermode INTEGER } dot1qVlanUngisterMCFilterVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "Per Vlan to configure multicast filtering function." ::= { dot1qVlanUngisterMCFilterEntry 1 } dot1qVlanUngisterMCFiltermode OBJECT-TYPE SYNTAX INTEGER {forwardall(2), filter(1), forward(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Filter unknown multicast frames or normal operation(i.e. forwarding)" ::= { dot1qVlanUngisterMCFilterEntry 2 } dot1qVlanPVIDAutoAssignOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable VLAN PVID auto assignment" ::= { companyDot1qVlanGroup 9 } -- ---------------------------------------------------------- -- The GVRP Groups -- ---------------------------------------------------------- gvrpGVRPGlobalSettingsOnOff OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable GVRP mechanism." ::= { companyGVRPGroup 1 } gvrpSettingsJoinTime OBJECT-TYPE SYNTAX INTEGER (100..100000) MAX-ACCESS read-write STATUS current DESCRIPTION "The Join Time value assigned to this Join Time field. This 16-bit value is read-write." ::= { companyGVRPGroup 2 } gvrpSettingsLeaveTime OBJECT-TYPE SYNTAX INTEGER (100..100000) MAX-ACCESS read-write STATUS current DESCRIPTION "The Leave Time value assigned to this Leave Time field. This 16-bit value is read-write." ::= { companyGVRPGroup 3 } gvrpSettingsLeaveAllTime OBJECT-TYPE SYNTAX INTEGER (100..100000) MAX-ACCESS read-write STATUS current DESCRIPTION "The Leave_All Time value assigned to this Leave_All Time field. This 16-bit value is read-write." ::= { companyGVRPGroup 4 } -- GRVP Port Setting Table -- gvrpSettingsTable OBJECT-TYPE SYNTAX SEQUENCE OF GvrpSettingsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing static configuration information for each GVRP configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset." ::= { companyGVRPGroup 5 } gvrpSettingsEntry OBJECT-TYPE SYNTAX GvrpSettingsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information for a GVRP configured into the device by (local or network) management." INDEX { gvrpSettingsPortControlIndex } ::= { gvrpSettingsTable 1 } GvrpSettingsEntry ::= SEQUENCE { gvrpSettingsPortControlIndex InterfaceIndex, gvrpSettingsPVID INTEGER, gvrpSettingsGVRPState INTEGER, gvrpSettingsIngressChecking INTEGER, gvrpSettingsAcceptableFrameType INTEGER } gvrpSettingsPortControlIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port." ::= { gvrpSettingsEntry 1 } gvrpSettingsPVID OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "The PVID value assigned to this Aggregation Port. This 16-bit value is read-write." ::= { gvrpSettingsEntry 2 } gvrpSettingsGVRPState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable GVRP State to this Aggregation Port." ::= { gvrpSettingsEntry 3 } gvrpSettingsIngressChecking OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Ingress Checking mechanism of GVRP to this Aggregation Port." ::= { gvrpSettingsEntry 4 } gvrpSettingsAcceptableFrameType OBJECT-TYPE SYNTAX INTEGER { allFrames(1), taggedOnly(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Chose types All Frames/Tagged to this Aggregation Port." ::= { gvrpSettingsEntry 5 } -- ---------------------------------------------------------- -- The DHCP/BOOTP Relay -- ---------------------------------------------------------- dhcpBOOTPRelayControl OBJECT IDENTIFIER ::= { companyDHCPRelay 1 } dhcpBOOTPRelayManagement OBJECT IDENTIFIER ::= { companyDHCPRelay 2 } dhcpBOOTPRelayManagementOption82 OBJECT IDENTIFIER ::= { dhcpBOOTPRelayManagement 2 } -- The DHCP/BOOTP Relay Control dhcpBOOTPRelayState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP relay function is enabled or disabled." ::= { dhcpBOOTPRelayControl 1 } dhcpBOOTPRelayHopCount OBJECT-TYPE SYNTAX INTEGER (1..16) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the maximum number of router hops that the BOOTP packets can cross." ::= { dhcpBOOTPRelayControl 2 } dhcpBOOTPRelayTimeThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet." ::= { dhcpBOOTPRelayControl 3 } dhcpBOOTPRelayEnablePortlist OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP relay function is enabled or disabled by portlist." ::= { dhcpBOOTPRelayControl 4 } dhcpRelayVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF DHCPRelayVlanSettings MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the IP address as a destination to forward (relay) DHCP packets to." ::= { dhcpBOOTPRelayControl 5 } dhcpRelayVlanTableEntry OBJECT-TYPE SYNTAX DHCPRelayVlanSettings MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information indicates the IP address as a destination to forward (relay) DHCP packets to." INDEX { dhcpRelayVlanSettingsVLANID } ::= { dhcpRelayVlanTable 1 } DHCPRelayVlanSettings ::= SEQUENCE { dhcpRelayVlanSettingsVLANID INTEGER, dhcpRelayVlanSettingsState INTEGER } dhcpRelayVlanSettingsVLANID OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays the current VLAN ID of the device." ::= { dhcpRelayVlanTableEntry 1 } dhcpRelayVlanSettingsState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP relay function of VLAN is enabled or disabled." ::= { dhcpRelayVlanTableEntry 2 } -- The DHCP/BOOTP Relay Management -- The DHCP/BOOTP Relay Interface Settings Table dhcpBOOTPRelayInterfaceSettingsTable OBJECT-TYPE SYNTAX SEQUENCE OF DHCPBOOTPRelayInterfaceSettings MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the IP address as a destination to forward (relay) DHCP packets to." ::= { dhcpBOOTPRelayManagement 1 } dhcpBOOTPRelayInterfaceSettingsEntry OBJECT-TYPE SYNTAX DHCPBOOTPRelayInterfaceSettings MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information indicates the IP address as a destination to forward (relay) DHCP packets to." INDEX { dhcpBOOTPRelayInterface, dhcpBOOTPRelayServerIP} ::= { dhcpBOOTPRelayInterfaceSettingsTable 1 } DHCPBOOTPRelayInterfaceSettings ::= SEQUENCE { dhcpBOOTPRelayInterface DisplayString, dhcpBOOTPRelayServerIP IpAddress, dhcpBOOTPRelayInterfaceSettingsRowStatus RowStatus } dhcpBOOTPRelayInterface OBJECT-TYPE SYNTAX DisplayString (SIZE(0..12)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the name of the IP interface." ::= { dhcpBOOTPRelayInterfaceSettingsEntry 1 } dhcpBOOTPRelayServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the DHCP server IP address." ::= { dhcpBOOTPRelayInterfaceSettingsEntry 2 } dhcpBOOTPRelayInterfaceSettingsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { dhcpBOOTPRelayInterfaceSettingsEntry 3 } -- The DHCP/BOOTP Relay Management -- The DHCP/BOOTP Relay Option82 dhcpBOOTPRelayOption82State OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP relay option 82 function is enabled or disabled." ::= { dhcpBOOTPRelayManagementOption82 1 } dhcpBOOTPRelayOption82CheckState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP relay option 82 Check function is enabled or disabled." ::= { dhcpBOOTPRelayManagementOption82 2 } dhcpBOOTPRelayOption82Policy OBJECT-TYPE SYNTAX INTEGER { replace(1), drop(2), keep(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP relay option 82 policy." ::= { dhcpBOOTPRelayManagementOption82 3 } dhcpBOOTPRelayOption82RemoteIDType OBJECT-TYPE SYNTAX INTEGER { default(1), userdefined(2), userdefinedhex(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the type of remote ID. If the type is default, the remote ID will be the MAC address of the device, otherwise, the remote ID can be defined by writing to the swDHCPRelayOption82RemoteID object." ::= { dhcpBOOTPRelayManagementOption82 4 } dhcpBOOTPRelayOption82RemoteID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object displays the current remote ID of the device. If swDHCPRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If swDHCPRelayOption82RemoteIDType is set to user-defined or user-defined-hex, a new value can be written to this object." ::= { dhcpBOOTPRelayManagementOption82 5 } dhcpBOOTPRelayOption82CircuitIDType OBJECT-TYPE SYNTAX INTEGER { default(1), userdefined(2), userdefinedhex(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the type of remote ID. If the type is default, the circuit ID will be blank, otherwise, the circuit ID can be defined by writing to the dhcpBOOTPRelayOption82CircuitID object." ::= { dhcpBOOTPRelayManagementOption82 7 } dhcpBOOTPRelayOption82CircuitID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object displays the current remote ID of the device. If dhcpBOOTPRelayOption82CircuitIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If dhcpBOOTPRelayOption82CircuitIDType is set to user-defined or user-defined-hex, a new value can be written to this object." ::= { dhcpBOOTPRelayManagementOption82 8 } -- ---------------------------------------------------------- -- The DHCP LocalRelay -- ---------------------------------------------------------- -- The DHCP Local Relay Table dhcpLocalRelayGlobalState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP local relay function of VLAN is enabled or disabled." ::= { companyDHCPLocalRelay 1 } dhcpLocalRelayTable OBJECT-TYPE SYNTAX SEQUENCE OF DHCPLocalRelaySettings MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the IP address as a destination to forward (local relay) DHCP packets to." ::= { companyDHCPLocalRelay 2 } dhcpLocalRelayTableEntry OBJECT-TYPE SYNTAX DHCPLocalRelaySettings MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information indicates the IP address as a destination to forward (local relay) DHCP packets to." INDEX { dhcpLocalRelaySettingsVLANID } ::= { dhcpLocalRelayTable 1 } DHCPLocalRelaySettings ::= SEQUENCE { dhcpLocalRelaySettingsVLANID INTEGER, dhcpLocalRelaySettingsState INTEGER } dhcpLocalRelaySettingsVLANID OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays the current VLAN ID of the device." ::= { dhcpLocalRelayTableEntry 1 } dhcpLocalRelaySettingsState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP local relay function of VLAN is enabled or disabled." ::= { dhcpLocalRelayTableEntry 2 } dhcpLocalRelayEnablePortlist OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCP local relay function is enabled or disabled by portlist." ::= { companyDHCPLocalRelay 3 } -- --------------------------------------------------------------------- -- LA Function -- --------------------------------------------------------------------- laSystem OBJECT IDENTIFIER ::= { companyLA 1 } laPortControl OBJECT IDENTIFIER ::= { companyLA 2 } -- ------------------------------------------------------------- -- Textual Conventions -- ------------------------------------------------------------- PortLaMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Defines how a Port Channel does channeling. lacp(1) - place the port into passive negotiation state, in which the port waits for its peer to initiate negotiation. static(2) - force the port to enable channeling. disable(3) - channeling is disabled." SYNTAX INTEGER { lacp(1), static(2), disable(3) } LacpKey ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The Actor or Partner Key value (0..65535)." SYNTAX Integer32 (0..65535) -- ------------------------------------------------------------------ -- The La System Group -- ------------------------------------------------------------------ laStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the Link Aggregation Module administrative status as enabled or disabled." ::= { laSystem 2 } -- -- Port Channel Table -- laPortChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF LaPortChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel." ::= { laSystem 3 } laPortChannelEntry OBJECT-TYPE SYNTAX LaPortChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each created port-channel port." INDEX { laPortChannelIfIndex } ::= { laPortChannelTable 1 } LaPortChannelEntry ::= SEQUENCE { laPortChannelIfIndex InterfaceIndex, laPortChannelMemberList PortList, laPortChannelMode PortLaMode -- start CAMEO_LA_MASTER_PORT_WANTED , laPortChannelMasterPort InterfaceIndex -- end CAMEO_LA_MASTER_PORT_WANTED } laPortChannelIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port-channel(Aggregator's interface index). " ::= { laPortChannelEntry 1 } laPortChannelMemberList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Member Port list of the port channel. Add the ports as a aggregation member associated of a port-channel." ::= { laPortChannelEntry 2 } laPortChannelMode OBJECT-TYPE SYNTAX PortLaMode MAX-ACCESS read-write STATUS current DESCRIPTION "Current Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (Manual). disable(3) - channeling is disabled." ::= { laPortChannelEntry 3 } -- start CAMEO_LA_MASTER_PORT_WANTED laPortChannelMasterPort OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-write STATUS current DESCRIPTION "The master port of the port-channel. " ::= { laPortChannelEntry 4 } -- end CAMEO_LA_MASTER_PORT_WANTED -- ------------------------------------------------------------------ -- The La Algorithm Group -- ------------------------------------------------------------------ laAlgorithm OBJECT-TYPE SYNTAX INTEGER { sourceMAC(1), destMAC(2), sourceAndDestMAC(3), sourceIP(4), destIP(5), sourceAndDestIP(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the Link Aggregation load balance algorithm." ::= { laSystem 4 } -- -- LA Port Control Table -- laPortControlTable OBJECT-TYPE SYNTAX SEQUENCE OF LaPortControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains Link Aggregation Control configuration information about every Aggregation Port associated with this device. A row appears in this table for each physical port." ::= { laPortControl 1 } laPortControlEntry OBJECT-TYPE SYNTAX LaPortControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Link Aggregation Control configuration parameters for each Aggregation Port on this device." INDEX { laPortControlIndex } ::= { laPortControlTable 1 } LaPortControlEntry ::= SEQUENCE { laPortControlIndex InterfaceIndex, laPortActorPortPriority INTEGER, laPortActorActivity INTEGER, laPortActorTimeout INTEGER } laPortControlIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port." ::= { laPortControlEntry 1 } laPortActorPortPriority OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The priority value assigned to this Aggregation Port. This 16-bit value is read-write." ::= { laPortControlEntry 2 } laPortActorActivity OBJECT-TYPE SYNTAX INTEGER { active(1), passive(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates LACP_Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send frames along the configured links. If the actor and partner are both in passive mode, they do not exchange LACP packets." ::= { laPortControlEntry 3 } laPortActorTimeout OBJECT-TYPE SYNTAX INTEGER { short(1), long(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates LACP_Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds." ::= { laPortControlEntry 4 } -- ---------------------------------------------------------------- -- The STATIC MAC group -- ---------------------------------------------------------------- staticVlanBaseTable OBJECT IDENTIFIER ::= { companyStaticMAC 5 } staticDisableAutoLearn OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set on to disable Auto Learning Excluding Uplink Port and set off to enable Auto Learning." ::= { companyStaticMAC 1 } staticAutoLearningList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The set of the device's member ports that belong to the Static MAC auto learning enable/disable. For example, when Disable Auto Learning is enable, the octet value set up as '# 0x0F 0xFF 0xFF 0xFF' means from port 1 to port 4 are not in auto learning state, the other ports are in auto learning state. It can be set up when Disable Auto Learning is enable." ::= { companyStaticMAC 2 } staticTable OBJECT-TYPE SYNTAX SEQUENCE OF StaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the Static MACs" ::= { companyStaticMAC 3 } staticEntry OBJECT-TYPE SYNTAX StaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Static MAC entry containing the mac and forwarding port." INDEX { staticVlanID, staticMac,staticPort} ::= { staticTable 1 } StaticEntry ::= SEQUENCE { staticVlanID INTEGER, staticMac MacAddress, staticPort INTEGER, staticStatus RowStatus } staticVlanID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the static MAC entry." ::= { staticEntry 1 } staticMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the static MAC entry." ::= { staticEntry 2 } staticPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The forwarding port of the static MAC entry." ::= { staticEntry 3 } staticStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static MAC." ::= { staticEntry 4 } autoFdbTable OBJECT-TYPE SYNTAX SEQUENCE OF AutoFdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the Auto Fdb" ::= { companyStaticMAC 4 } autoFdbEntry OBJECT-TYPE SYNTAX AutoFdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A auto fdb entry containing the ipaddress" INDEX { autoFdbIPAddress} ::= { autoFdbTable 1 } AutoFdbEntry ::= SEQUENCE { autoFdbIPAddress IpAddress, autoFdbVlanID Integer32, autoFdbMacAddress MacAddress, autoFdbPort INTEGER, autoFdbTimeStamp Integer32, autoFdbStatus RowStatus } autoFdbIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IpAddress of the autoFdbEntry." ::= { autoFdbEntry 1 } autoFdbVlanID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VlanID of the autoFdbEntry." ::= { autoFdbEntry 2 } autoFdbMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Mac Address of the autoFdbEntry." ::= { autoFdbEntry 3 } autoFdbPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The Port of the autoFdbEntry." ::= { autoFdbEntry 4 } autoFdbTimeStamp OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Time Stamp of the autoFdbEntry." ::= { autoFdbEntry 5 } autoFdbStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of an entry in the Auto Fdb Table. Only a subset of the rowstatus variables (createAndGo, createAndWait,destroy) are available." ::= { autoFdbEntry 6 } staticVlanBaseAutoLearnList1k OBJECT-TYPE SYNTAX OCTET STRING(SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this Auto Learn, the bit corresponding to that VLAN is set to '1'. Write AutoLearnList1k use 256 character, and conform to the foregoing rules." ::= { staticVlanBaseTable 1 } staticVlanBaseAutoLearnList2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1025 through 2048. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this Auto Learn. Write AutoLearnList2k use 256 character, and conform to the foregoing rules." ::= { staticVlanBaseTable 2 } staticVlanBaseAutoLearnList3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2049 through 3072. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this Auto Learn the bit corresponding to that VLAN is set to '1'. Write AutoLearnList3k use 256 character, and conform to the foregoing rules." ::= { staticVlanBaseTable 3 } staticVlanBaseAutoLearnList4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3073 through 4094. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this Auto Learn the bit corresponding to that VLAN is set to '1'. Write AutoLearnList4k use 256 character, and conform to the foregoing rules." ::= { staticVlanBaseTable 4 } staticVlanBaseEnableAutoLearn OBJECT-TYPE SYNTAX OCTET STRING(SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "Set enable vlan list to auto learn, and range 1-4094." ::= { staticVlanBaseTable 5 } staticVlanBaseDisableAutoLearn OBJECT-TYPE SYNTAX OCTET STRING(SIZE (0..512)) MAX-ACCESS read-write STATUS current DESCRIPTION "Set disable vlan list to auto learn, and range 1-4094." ::= { staticVlanBaseTable 6 } -- --------------------------------------------------------------------- -- IGMP Snooping Function -- --------------------------------------------------------------------- igsSystem OBJECT IDENTIFIER ::= { companyIgsGroup 1 } igsVlan OBJECT IDENTIFIER ::= { companyIgsGroup 3 } igsAccessAuth OBJECT IDENTIFIER ::= { companyIgsGroup 5 } -- start IGMP_SNOOPING_HOST_BASED_FAST_LEAVE igsHost OBJECT IDENTIFIER ::= { companyIgsGroup 6 } -- end IGMP_SNOOPING_HOST_BASED_FAST_LEAVE igsStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops performing protocol operations." DEFVAL { 2 } ::= { igsSystem 1 } igsRouterPortPurgeInterval OBJECT-TYPE SYNTAX Integer32 (60..600) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted." DEFVAL { 260 } ::= { igsSystem 2 } igsHostPortPurgeInterval OBJECT-TYPE SYNTAX Integer32 (130..153025) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group." DEFVAL {260} ::= { igsSystem 3 } igsDataDrivenLearningMaxLearnedEntryVlaue OBJECT-TYPE SYNTAX INTEGER (1..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum data driven learning entry value." DEFVAL { 64 } ::= { igsSystem 8 } igsReportToAllPort OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module forwards packets to report to all port. When set to 'disabled', the IGS module forwards packets to router port only." DEFVAL { 2 } ::= { igsSystem 9 } -- VLAN Based MAC Multicast Forwarding Table -- -- igsVlanMcastMacFwdTable OBJECT-TYPE -- SYNTAX SEQUENCE OF IgsVlanMcastMacFwdEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "This table contains MAC based multicast forwarding -- information. This information is applicable only if -- the 'igsVlanMcastForwardingMode' is set to 'macbased' " -- ::= { igsVlan 1 } -- -- igsVlanMcastMacFwdEntry OBJECT-TYPE -- SYNTAX IgsVlanMcastMacFwdEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "This table contains VLAN ID, multicast group MAC address and the -- list of ports onto which the multicast data packets for group -- should be forwarded." -- -- INDEX { igsVlanMcastMacFwdVlanId, -- igsVlanMcastMacFwdGroupAddress } -- ::= { igsVlanMcastMacFwdTable 1 } -- -- IgsVlanMcastMacFwdEntry ::= SEQUENCE { -- igsVlanMcastMacFwdVlanId Integer32, -- igsVlanMcastMacFwdGroupAddress MacAddress, -- igsVlanMcastMacFwdPortList PortList -- } -- -- igsVlanMcastMacFwdVlanId OBJECT-TYPE -- SYNTAX Integer32 (1..4094) -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "VLAN ID pertaining to the Multicast forwarding entry" -- ::= { igsVlanMcastMacFwdEntry 1 } -- -- igsVlanMcastMacFwdGroupAddress OBJECT-TYPE -- SYNTAX MacAddress -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "Multicast group MAC address." -- ::= { igsVlanMcastMacFwdEntry 2 } -- -- -- igsVlanMcastMacFwdPortList OBJECT-TYPE -- SYNTAX PortList -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "List of ports onto which the multicast data -- packets destined for this group will be forwarded." -- ::= { igsVlanMcastMacFwdEntry 3 } -- VLAN based router table. igsVlanRouterTable OBJECT-TYPE SYNTAX SEQUENCE OF IgsVlanRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the list of ports through which a router, in a particular VLAN is reachable." ::= { igsVlan 3 } igsVlanRouterEntry OBJECT-TYPE SYNTAX IgsVlanRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the VLAN ID and list of ports on which routers are present in the VLAN." INDEX { igsVlanRouterVlanId } ::= { igsVlanRouterTable 1 } IgsVlanRouterEntry ::= SEQUENCE { igsVlanRouterVlanId Integer32, igsVlanRouterPortList PortList } igsVlanRouterVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID of the ports through which router is reachable." ::= { igsVlanRouterEntry 1 } igsVlanRouterPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically." ::= { igsVlanRouterEntry 2 } -- VLAN based filter table igsVlanFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF IgsVlanFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system." ::= { igsVlan 4 } igsVlanFilterEntry OBJECT-TYPE SYNTAX IgsVlanFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains snooping status , version and fast leave configuration for a specific VLAN." INDEX { igsVlanFilterVlanId } ::= { igsVlanFilterTable 1 } IgsVlanFilterEntry ::= SEQUENCE { igsVlanFilterVlanId Integer32, igsVlanSnoopStatus INTEGER, igsVlanQuerier INTEGER, igsVlanCfgQuerier INTEGER, igsVlanQueryInterval Integer32, igsVlanRtrPortList PortList ,igsVlanFbdRtrPortList PortList , igsVlanFastLeave INTEGER , igsVlanDataDrivenLearningStatus INTEGER , igsVlanQuerierVersionStatus INTEGER , igsVlanDataDrivenLearningAgeOutStatus INTEGER , igsVlanReportSuppression INTEGER , igsVlanRobustnessValue Integer32 , igsVlanGrpQueryInterval Integer32 , igsVlanQueryMaxResponseTime INTEGER } igsVlanFilterVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done." ::= { igsVlanFilterEntry 1 } igsVlanSnoopStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows you to enable/disable IGS function on a specific VLAN." DEFVAL { 1 } ::= { igsVlanFilterEntry 2 } igsVlanQuerier OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the switch is configured as a querier in the VLAN" DEFVAL { 2 } ::= { igsVlanFilterEntry 3 } igsVlanCfgQuerier OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries." DEFVAL { 2 } ::= { igsVlanFilterEntry 4 } igsVlanQueryInterval OBJECT-TYPE SYNTAX Integer32 (60..600) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network." DEFVAL { 125 } ::= { igsVlanFilterEntry 5 } igsVlanRtrPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "List of ports which are configured statically as router ports" ::= { igsVlanFilterEntry 6 } igsVlanFbdRtrPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "List of ports which can be configured statically as forbidden router ports." ::= { igsVlanFilterEntry 7 } igsVlanFastLeave OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table." DEFVAL { 2 } ::= { igsVlanFilterEntry 8 } igsVlanDataDrivenLearningStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows you to enable/disable Data Driven Learning function on a specific VLAN." ::= { igsVlanFilterEntry 9 } igsVlanQuerierVersionStatus OBJECT-TYPE SYNTAX INTEGER { igmp_v3(3), igmp_v2(2), igmp_v1(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows you to enable/disable Querier Version function on a specific VLAN." ::= { igsVlanFilterEntry 10 } igsVlanDataDrivenLearningAgeOutStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows you to enable/disable Data Driven Learning Age Out State on a specific VLAN." ::= { igsVlanFilterEntry 11 } igsVlanReportSuppression OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables Report suppression in the system." ::= { igsVlanFilterEntry 12 } igsVlanRobustnessValue OBJECT-TYPE SYNTAX Integer32 (2..255) MAX-ACCESS read-write STATUS current DESCRIPTION "When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'igsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group." DEFVAL { 2 } ::= { igsVlanFilterEntry 13 } igsVlanGrpQueryInterval OBJECT-TYPE SYNTAX Integer32 (1..25) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'igsRobustnessValue' queries before removing the port from the group membership information in the forwarding database." DEFVAL { 1 } ::= { igsVlanFilterEntry 14 } igsVlanQueryMaxResponseTime OBJECT-TYPE SYNTAX INTEGER (10..25) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum query response time advertised in IGMPv2 general queries on this interface." DEFVAL { 10 } ::= { igsVlanFilterEntry 15 } -- VLAN Based IGMP Snooping Group igsVlanMulticastGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF IgsVlanMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains MAC based multicast forwarding information." ::= { igsVlan 5 } igsVlanMulticastGroupEntry OBJECT-TYPE SYNTAX IgsVlanMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded." INDEX { igsVlanMulticastGroupVlanId, igsVlanMulticastGroupIpAddress } ::= { igsVlanMulticastGroupTable 1 } IgsVlanMulticastGroupEntry ::= SEQUENCE { igsVlanMulticastGroupVlanId Integer32, igsVlanMulticastGroupIpAddress InetAddress, igsVlanMulticastGroupMacAddress MacAddress, igsVlanMulticastGroupPortList PortList } igsVlanMulticastGroupVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID pertaining to the Multicast forwarding entry" ::= { igsVlanMulticastGroupEntry 1 } igsVlanMulticastGroupIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format." ::= { igsVlanMulticastGroupEntry 2 } igsVlanMulticastGroupMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format." ::= { igsVlanMulticastGroupEntry 3 } igsVlanMulticastGroupPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "List of ports onto which the multicast data packets destined for this group will be forwarded." ::= { igsVlanMulticastGroupEntry 4 } igsAccessAuthTable OBJECT-TYPE SYNTAX SEQUENCE OF IgsAccessAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to manage the IGMP Authentication function of the switch." ::= { igsAccessAuth 1 } igsAccessAuthEntry OBJECT-TYPE SYNTAX IgsAccessAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains management entities for IGMP Authentication function." INDEX { igsAccessAuthPortIndex } ::= { igsAccessAuthTable 1 } IgsAccessAuthEntry ::= SEQUENCE { igsAccessAuthPortIndex Integer32, igsAccessAuthState INTEGER } igsAccessAuthPortIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port index of igsAccessAuthTable which indicates the port to be configured." ::= { igsAccessAuthEntry 1 } igsAccessAuthState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object can be configured to set IGMP Authentication state to enabled/disabled on each port." ::= { igsAccessAuthEntry 2 } -- start IGMP_SNOOPING_HOST_BASED_FAST_LEAVE igsHostTable OBJECT-TYPE SYNTAX SEQUENCE OF IgsHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to manage the IGMP Host based Fast Leave function of the switch." ::= { igsHost 1 } igsHostEntry OBJECT-TYPE SYNTAX IgsHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains management entities for IGMP Host based fast leave function." INDEX {igsHostTableVLANID, igsHostTableGroupAddress, igsHostTablePort, igsHostTableHostIPAddress} ::= { igsHostTable 1 } IgsHostEntry ::= SEQUENCE { igsHostTableVLANID Integer32, igsHostTableGroupAddress InetAddress, igsHostTablePort Integer32, igsHostTableHostIPAddress InetAddress } igsHostTableVLANID OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID of Host table entry." ::= { igsHostEntry 1 } igsHostTableGroupAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Group address of Host table entry." ::= { igsHostEntry 2 } igsHostTablePort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Port number of Host table entry." ::= { igsHostEntry 3 } igsHostTableHostIPAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Host IP address of Group in Host table entry." ::= { igsHostEntry 4 } -- end IGMP_SNOOPING_HOST_BASED_FAST_LEAVE -- --------------------------------------------------------------------- -- MLD Snooping Function -- --------------------------------------------------------------------- mldsSystem OBJECT IDENTIFIER ::= { companyMldsGroup 1 } mldsVlan OBJECT IDENTIFIER ::= { companyMldsGroup 3 } mldsHost OBJECT IDENTIFIER ::= { companyMldsGroup 4 } mldsStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables MLD snooping in the system. When set to 'enabled', the MLDS module starts protocol operations. When set to 'disabled', the MLDS module stops performing protocol operations." DEFVAL { 2 } ::= { mldsSystem 1 } mldsRouterPortPurgeInterval OBJECT-TYPE SYNTAX Integer32 (60..600) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted." DEFVAL { 260 } ::= { mldsSystem 2 } mldsHostPortPurgeInterval OBJECT-TYPE SYNTAX Integer32 (130..153025) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group." DEFVAL {260} ::= { mldsSystem 3 } mldsDataDrivenLearningMaxLearnedEntryVlaue OBJECT-TYPE SYNTAX INTEGER (1..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum data driven learning entry value." DEFVAL { 64 } ::= { mldsSystem 8 } -- VLAN based router table. mldsVlanRouterTable OBJECT-TYPE SYNTAX SEQUENCE OF MldsVlanRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the list of ports through which a router, in a particular VLAN is reachable." ::= { mldsVlan 3 } mldsVlanRouterEntry OBJECT-TYPE SYNTAX MldsVlanRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains the VLAN ID and list of ports on which routers are present in the VLAN." INDEX { mldsVlanRouterVlanId } ::= { mldsVlanRouterTable 1 } MldsVlanRouterEntry ::= SEQUENCE { mldsVlanRouterVlanId Integer32, mldsVlanRouterPortList PortList } mldsVlanRouterVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID of the ports through which router is reachable." ::= { mldsVlanRouterEntry 1 } mldsVlanRouterPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically." ::= { mldsVlanRouterEntry 2 } -- VLAN based filter table mldsVlanFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF MldsVlanFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system." ::= { mldsVlan 4 } mldsVlanFilterEntry OBJECT-TYPE SYNTAX MldsVlanFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains snooping status , version and fast leave configuration for a specific VLAN." INDEX { mldsVlanFilterVlanId } ::= { mldsVlanFilterTable 1 } MldsVlanFilterEntry ::= SEQUENCE { mldsVlanFilterVlanId Integer32, mldsVlanSnoopStatus INTEGER, mldsVlanQuerier INTEGER, mldsVlanCfgQuerier INTEGER, mldsVlanQueryInterval Integer32, mldsVlanRtrPortList PortList , mldsVlanFbdRtrPortList PortList , mldsVlanFastLeave INTEGER , mldsVlanDataDrivenLearningStatus INTEGER , mldsVlanReportSuppression INTEGER , mldsVlanRobustnessValue Integer32 , mldsVlanGrpQueryInterval Integer32 , mldsVlanQueryMaxResponseTime INTEGER } mldsVlanFilterVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "Index of MldsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in MldsVlanFilterEntry is to be done." ::= { mldsVlanFilterEntry 1 } mldsVlanSnoopStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows you to enable/disable MLDS function on a specific VLAN." DEFVAL { 1 } ::= { mldsVlanFilterEntry 2 } mldsVlanQuerier OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the switch is configured as a querier in the VLAN" DEFVAL { 2 } ::= { mldsVlanFilterEntry 3 } mldsVlanCfgQuerier OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The snooping switch can be configured as a querier via this object to send out MLD general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries." DEFVAL { 2 } ::= { mldsVlanFilterEntry 4 } mldsVlanQueryInterval OBJECT-TYPE SYNTAX Integer32 (60..600) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network." DEFVAL { 125 } ::= { mldsVlanFilterEntry 5 } mldsVlanRtrPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "List of ports which are configured statically as router ports" ::= { mldsVlanFilterEntry 6 } mldsVlanFbdRtrPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "List of ports which can be configured statically as forbidden router ports." ::= { mldsVlanFilterEntry 7 } mldsVlanFastLeave OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table." DEFVAL { 2 } ::= { mldsVlanFilterEntry 8 } mldsVlanDataDrivenLearningStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object allows you to enable/disable Data Driven Learning function on a specific VLAN." ::= { mldsVlanFilterEntry 9 } mldsVlanReportSuppression OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or disables Report suppression in the system." ::= { mldsVlanFilterEntry 10 } mldsVlanRobustnessValue OBJECT-TYPE SYNTAX Integer32 (2..255) MAX-ACCESS read-write STATUS current DESCRIPTION "When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'mldsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group." DEFVAL { 2 } ::= { mldsVlanFilterEntry 11 } mldsVlanGrpQueryInterval OBJECT-TYPE SYNTAX Integer32 (1..25) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'mldsRobustnessValue' queries before removing the port from the group membership information in the forwarding database." DEFVAL { 1 } ::= { mldsVlanFilterEntry 12 } mldsVlanQueryMaxResponseTime OBJECT-TYPE SYNTAX INTEGER (10..25) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum query response time advertised in MLDv1 general queries on this interface." DEFVAL { 10 } ::= { mldsVlanFilterEntry 13 } -- VLAN Based MLD Snooping Group mldsVlanMulticastGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MldsVlanMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains MAC based multicast forwarding information." ::= { mldsVlan 5 } mldsVlanMulticastGroupEntry OBJECT-TYPE SYNTAX MldsVlanMulticastGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded." INDEX { mldsVlanMulticastGroupVlanId, mldsVlanMulticastGroupIpAddress } ::= { mldsVlanMulticastGroupTable 1 } MldsVlanMulticastGroupEntry ::= SEQUENCE { mldsVlanMulticastGroupVlanId Integer32, mldsVlanMulticastGroupIpAddress InetAddress, mldsVlanMulticastGroupMacAddress MacAddress, mldsVlanMulticastGroupPortList PortList } mldsVlanMulticastGroupVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID pertaining to the Multicast forwarding entry" ::= { mldsVlanMulticastGroupEntry 1 } mldsVlanMulticastGroupIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format." ::= { mldsVlanMulticastGroupEntry 2 } mldsVlanMulticastGroupMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format." ::= { mldsVlanMulticastGroupEntry 3 } mldsVlanMulticastGroupPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "List of ports onto which the multicast data packets destined for this group will be forwarded." ::= { mldsVlanMulticastGroupEntry 4 } -- Host Table mldsHostTable OBJECT-TYPE SYNTAX SEQUENCE OF MldsHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to manage the IGMP Host based Fast Leave function of the switch." ::= { mldsHost 1 } mldsHostEntry OBJECT-TYPE SYNTAX MldsHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Contains management entities for IGMP Host based fast leave function." INDEX {mldsHostTableVLANID, mldsHostTableGroupAddress, mldsHostTablePort, mldsHostTableHostIPAddress} ::= { mldsHostTable 1 } MldsHostEntry ::= SEQUENCE { mldsHostTableVLANID Integer32, mldsHostTableGroupAddress Ipv6Address, mldsHostTablePort Integer32, mldsHostTableHostIPAddress Ipv6Address } mldsHostTableVLANID OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID of IPv6 Host table entry." ::= { mldsHostEntry 1 } mldsHostTableGroupAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "Group address of IPv6 Host table entry." ::= { mldsHostEntry 2 } mldsHostTablePort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Port number of IPv6 Host table entry." ::= { mldsHostEntry 3 } mldsHostTableHostIPAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "Host IP address of Group in IPv6 Host table entry." ::= { mldsHostEntry 4 } -- ------------------------------------------------------------- -- groups in the Auth MIB -- ------------------------------------------------------------- swAuthenCtrl OBJECT IDENTIFIER ::= { companyAuthGroup 1 } -- ----------------------------------------------------------------------------- -- swAuthenCtrl -- ----------------------------------------------------------------------------- swAuthStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Static 802.1x." ::= { swAuthenCtrl 1 } swAuthMode OBJECT-TYPE SYNTAX INTEGER { portBase(1), macBase(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the authentication mode of the device." ::= { swAuthenCtrl 2 } authProtocol OBJECT-TYPE SYNTAX INTEGER { authProtocolRadiusEap(1), authProtocolLocal(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The authentication method used to authenticate users." DEFVAL { authProtocolRadiusEap } ::= { swAuthenCtrl 3 } -- start CAMEO_EAP_TRANSPARENT_FILTERING swAuthCtrlPktFwdMode OBJECT-TYPE SYNTAX INTEGER { authForwardEap(1), authDropEap(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When 802.1x disable, this item can decided eap packet be forward or drop." DEFVAL { authForwardEap } ::= { swAuthenCtrl 4 } -- end CAMEO_EAP_TRANSPARENT_FILTERING -- ------------------------------------------------------------- -- groups in the Port Access Control MIB -- ------------------------------------------------------------- swAuthPortAccessCtrl OBJECT IDENTIFIER ::= { companyAuthGroup 2 } -- ----------------------------------------------------------------------------- -- swAuthPortAccessCtrl -- ----------------------------------------------------------------------------- swAuthPortAccessControlTable OBJECT-TYPE SYNTAX SEQUENCE OF SwAuthPortAccessControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself." ::= { swAuthPortAccessCtrl 1 } swAuthPortAccessControlEntry OBJECT-TYPE SYNTAX SwAuthPortAccessControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration information for an Authenticator Port." INDEX { swAuthAuthConfigPortNumber } ::= { swAuthPortAccessControlTable 1 } SwAuthPortAccessControlEntry ::= SEQUENCE { swAuthAuthConfigPortNumber INTEGER, swAuthAuthQuietPeriod INTEGER, swAuthAuthSuppTimeout INTEGER, swAuthAuthServerTimeout INTEGER, swAuthAuthMaxReq INTEGER, swAuthAuthTxPeriod INTEGER, swAuthAuthReAuthPeriod INTEGER, swAuthAuthReAuthentication INTEGER, swAuthAuthConfigPortControl INTEGER, swAuthAuthCapability INTEGER, swAuthAuthDirection INTEGER } swAuthAuthConfigPortNumber OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number." ::= { swAuthPortAccessControlEntry 1 } swAuthAuthQuietPeriod OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine." REFERENCE "9.4.1, quietPeriod." DEFVAL { 60 } ::= { swAuthPortAccessControlEntry 2 } swAuthAuthSuppTimeout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine." REFERENCE "9.4.1, suppTimeout." DEFVAL { 12 } ::= { swAuthPortAccessControlEntry 3 } swAuthAuthServerTimeout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine." REFERENCE "9.4.1, serverTimeout." DEFVAL { 16 } ::= { swAuthPortAccessControlEntry 4 } swAuthAuthMaxReq OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of the maxReq constant currently in use by the Backend Authentication state machine." REFERENCE "9.4.1, maxReq." DEFVAL { 2 } ::= { swAuthPortAccessControlEntry 5 } swAuthAuthTxPeriod OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine." REFERENCE "9.4.1, txPeriod." DEFVAL { 24 } ::= { swAuthPortAccessControlEntry 6 } swAuthAuthReAuthPeriod OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine." REFERENCE "9.4.1, reAuthPerio." DEFVAL { 3600 } ::= { swAuthPortAccessControlEntry 7 } swAuthAuthReAuthentication OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1)." REFERENCE "9.4.1, reAuthEnable." ::= { swAuthPortAccessControlEntry 8 } swAuthAuthConfigPortControl OBJECT-TYPE SYNTAX INTEGER { forceUnauthorized(1), auto(2), forceAuthorized(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The current value of the controlled Port control parameter for the Port." REFERENCE "9.4.1, AuthControlledPortControl." ::= { swAuthPortAccessControlEntry 9 } swAuthAuthCapability OBJECT-TYPE SYNTAX INTEGER { authenticator(1), none(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The current value of the controlled Port control parameter for the Port." REFERENCE "AuthCapability." ::= { swAuthPortAccessControlEntry 10 } swAuthAuthDirection OBJECT-TYPE SYNTAX INTEGER { both(0), in(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The current value of the controlled Port control parameter for the Port." REFERENCE "AuthDirection." ::= { swAuthPortAccessControlEntry 11 } -- ------------------------------------------------------------- -- groups in the 802.1X Local user MIB -- ------------------------------------------------------------- swAuthUser OBJECT IDENTIFIER ::= { companyAuthGroup 3 } -- ----------------------------------------------------------------------------- -- swAuthUser -- ----------------------------------------------------------------------------- swAuthUserTable OBJECT-TYPE SYNTAX SEQUENCE OF SwAuthUserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself." ::= { swAuthUser 1 } swAuthUserEntry OBJECT-TYPE SYNTAX SwAuthUserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration information for an Authenticator Port." INDEX { swAuthUserName } ::= { swAuthUserTable 1 } SwAuthUserEntry ::= SEQUENCE { swAuthUserName SnmpAdminString, swAuthUserPassword DisplayString, swAuthUserStatus RowStatus } swAuthUserName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "The unique index value of a row in this table. This object is used to set 802.1X Local user name, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark." ::= { swAuthUserEntry 1 } swAuthUserPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set 802.1X Local user Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark." ::= { swAuthUserEntry 2 } swAuthUserStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row in the swAuthUserTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthUserName objects must be explicitly set." ::= { swAuthUserEntry 3 } -- ------------------------------------------------------------- -- groups in the Authentication RADIUS Server MIB -- ------------------------------------------------------------- swAuthRadiusServer OBJECT IDENTIFIER ::= { companyAuthGroup 4 } -- ----------------------------------------------------------------------------- -- swAuthRadiusServer -- ----------------------------------------------------------------------------- iPv4swAuthRadiusServerTable OBJECT-TYPE SYNTAX SEQUENCE OF IPv4SwAuthRadiusServerEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself." ::= { swAuthRadiusServer 1 } iPv4swAuthRadiusServerEntry OBJECT-TYPE SYNTAX IPv4SwAuthRadiusServerEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "The configuration information for an Authenticator Port." INDEX { iPv4swAuthRadiusServerIndex } ::= { iPv4swAuthRadiusServerTable 1 } IPv4SwAuthRadiusServerEntry ::= SEQUENCE { iPv4swAuthRadiusServerIndex INTEGER, iPv4swAuthRadiusServerAddress IpAddress, iPv4swAuthRadiusServerAuthenticationPort INTEGER, iPv4swAuthRadiusServerAccountingPort INTEGER, iPv4swAuthRadiusServerTimeout INTEGER, iPv4swAuthRadiusServerRetransmit INTEGER, iPv4swAuthRadiusServerKey DisplayString, iPv4swAuthRadiusServerStatus RowStatus } iPv4swAuthRadiusServerIndex OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-only STATUS obsolete DESCRIPTION "A unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3." ::= { iPv4swAuthRadiusServerEntry 1 } iPv4swAuthRadiusServerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The IP address of the RADIUS server referred to in this table entry." ::= { iPv4swAuthRadiusServerEntry 2 } iPv4swAuthRadiusServerAuthenticationPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The value is for setting UDP Port." DEFVAL { 1812 } ::= { iPv4swAuthRadiusServerEntry 3 } iPv4swAuthRadiusServerAccountingPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The value is for setting UDP Port." DEFVAL { 1813 } ::= { iPv4swAuthRadiusServerEntry 4 } iPv4swAuthRadiusServerTimeout OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The value is for setting UDP Port." DEFVAL { 5 } ::= { iPv4swAuthRadiusServerEntry 5 } iPv4swAuthRadiusServerRetransmit OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The value is for setting UDP Port." DEFVAL { 2 } ::= { iPv4swAuthRadiusServerEntry 6 } iPv4swAuthRadiusServerKey OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "This object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark." ::= { iPv4swAuthRadiusServerEntry 7 } iPv4swAuthRadiusServerStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS obsolete DESCRIPTION "The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthRadiusServerIndex objects must be explicitly set." ::= { iPv4swAuthRadiusServerEntry 8 } -- ----------------------------------------------------------------------------- -- swAuthRadiusServer for IPv6 -- ----------------------------------------------------------------------------- swAuthRadiusServerTable OBJECT-TYPE SYNTAX SEQUENCE OF SwAuthRadiusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself." ::= { swAuthRadiusServer 2 } swAuthRadiusServerEntry OBJECT-TYPE SYNTAX SwAuthRadiusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration information for an Authenticator Port." INDEX { swAuthRadiusServerIndex } ::= { swAuthRadiusServerTable 1 } SwAuthRadiusServerEntry ::= SEQUENCE { swAuthRadiusServerIndex INTEGER, swAuthRadiusIPType INTEGER, swAuthRadiusServerAddress Ipv6Address, swAuthRadiusServerInterfaceName OCTET STRING, swAuthRadiusServerAuthenticationPort INTEGER, swAuthRadiusServerAccountingPort INTEGER, swAuthRadiusServerTimeout INTEGER, swAuthRadiusServerRetransmit INTEGER, swAuthRadiusServerKey DisplayString, swAuthRadiusServerStatus RowStatus } swAuthRadiusServerIndex OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3." ::= { swAuthRadiusServerEntry 1 } swAuthRadiusIPType OBJECT-TYPE SYNTAX INTEGER (1..2) MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the RADIUS server IP type referred to in this table entry." DEFVAL { 1 } ::= { swAuthRadiusServerEntry 2 } swAuthRadiusServerAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the RADIUS server referred to in this table entry." ::= { swAuthRadiusServerEntry 3 } swAuthRadiusServerInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the interface name when the swAuthRadiusServerAddress is linklocal address." ::= { swAuthRadiusServerEntry 4 } swAuthRadiusServerAuthenticationPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value is for setting UDP Port." DEFVAL { 1812 } ::= { swAuthRadiusServerEntry 5 } swAuthRadiusServerAccountingPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value is for setting UDP Port." DEFVAL { 1813 } ::= { swAuthRadiusServerEntry 6 } swAuthRadiusServerTimeout OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The value is for setting UDP Port." DEFVAL { 5 } ::= { swAuthRadiusServerEntry 7 } swAuthRadiusServerRetransmit OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The value is for setting UDP Port." DEFVAL { 2 } ::= { swAuthRadiusServerEntry 8 } swAuthRadiusServerKey OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark." ::= { swAuthRadiusServerEntry 9 } swAuthRadiusServerStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthRadiusServerIndex objects must be explicitly set." ::= { swAuthRadiusServerEntry 10 } -- ------------------------------------------------------------------ -- QoS -- ------------------------------------------------------------------ --1-- cosScheduleMechanism OBJECT-TYPE SYNTAX INTEGER { strictPriority(1), wrr(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority scheduler node that is stacked directly above the port. Queues stacked on top of the strict-priority scheduler node always get bandwidth before other queues. Weighted round-robin scheduling is designed to better handle queues with different processing capacities. Each queue has a weight : Low is 1, Medium is 2, High is 4 and Highest is 8 for WS3 spec. Queues with higher weights get bandwidth before than other queues with less weights. " ::= { companyQoSGroup 1 } --2-- cosOutputSchedule OBJECT IDENTIFIER ::= { companyQoSGroup 2 } cosClassTable OBJECT-TYPE SYNTAX SEQUENCE OF CosClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of cosOutputSchedule." ::= { cosOutputSchedule 1 } cosClassEntry OBJECT-TYPE SYNTAX CosClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of cosOutputClass Weight." INDEX { cosClassIndex } ::= { cosClassTable 1 } CosClassEntry ::= SEQUENCE { cosClassIndex INTEGER, cosWeight INTEGER } cosClassIndex OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "A index of class 0 ~ 7." ::= { cosClassEntry 1 } cosWeight OBJECT-TYPE SYNTAX INTEGER (1..55) MAX-ACCESS read-write STATUS current DESCRIPTION "cos weight " ::= { cosClassEntry 2 } cosBandwidthCtrlSettings OBJECT IDENTIFIER ::= { companyQoSGroup 9 } cosBandwidthCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF CosBandwidthCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of cosBandwidthCtrlEntry default priority Entries." ::= { cosBandwidthCtrlSettings 1 } cosBandwidthCtrlEntry OBJECT-TYPE SYNTAX CosBandwidthCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of cosBandwidthCtrlEntry default priority priorities." INDEX { cosBandwidthCtrlPortIndex, cosBandwidthCtrlClassIndex } ::= { cosBandwidthCtrlTable 1 } CosBandwidthCtrlEntry ::= SEQUENCE { cosBandwidthCtrlPortIndex Integer32, cosBandwidthCtrlClassIndex INTEGER, cosBandwidthValue Integer32 } cosBandwidthCtrlPortIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A port identifier that is in the range of 1 to ifNumber." ::= { cosBandwidthCtrlEntry 1 } cosBandwidthCtrlClassIndex OBJECT-TYPE SYNTAX INTEGER (0..3) MAX-ACCESS read-only STATUS current DESCRIPTION "A BandwidthCtrlClassIndex identifier that is in the range of 1 to ifNumber." ::= { cosBandwidthCtrlEntry 2 } cosBandwidthValue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The BandwidthValue return value." ::= { cosBandwidthCtrlEntry 3 } -- ------------------------------------------------------------------ -- QoS -- ------------------------------------------------------------------ --4 default user priority-- qosDefaultUserPri OBJECT IDENTIFIER ::= { companyQoSGroup 4 } qosDefaultUserPriTable OBJECT-TYPE SYNTAX SEQUENCE OF QosDefaultUserPriEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of 802.1p port default priority Entries." ::= { qosDefaultUserPri 1 } qosDefaultUserPriEntry OBJECT-TYPE SYNTAX QosDefaultUserPriEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of 802.1p port default priority priorities." INDEX { qosDefaultUserPriPortIndex } ::= { qosDefaultUserPriTable 1 } QosDefaultUserPriEntry ::= SEQUENCE { qosDefaultUserPriPortIndex INTEGER, qosDefaultPriority INTEGER, qosEffectiveDefaultPriority INTEGER } qosDefaultUserPriPortIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "A port identifier that is in the range of 1 to ifNumber." ::= { qosDefaultUserPriEntry 1 } qosDefaultPriority OBJECT-TYPE SYNTAX INTEGER { priority0(0), priority1(1), priority2(2), priority3(3), priority4(4), priority5(5), priority6(6), priority7(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled." ::= { qosDefaultUserPriEntry 2 } qosEffectiveDefaultPriority OBJECT-TYPE SYNTAX INTEGER { priority0(0), priority1(1), priority2(2), priority3(3), priority4(4), priority5(5), priority6(6), priority7(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "For ingress untagged packets, the per port 'Effective Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled." ::= { qosDefaultUserPriEntry 3 } --5 vlan tag user priority -- qosUserPriority OBJECT IDENTIFIER ::= { companyQoSGroup 5 } qosUserPriorityTable OBJECT-TYPE SYNTAX SEQUENCE OF QosUserPriEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table mapping evaluated User Priority to Traffic Class, for forwarding by the bridge. Traffic class is a number in the range (0..3)." REFERENCE "ISO/IEC 15802-3 Table 7-2" ::= { qosUserPriority 1 } qosUserPriEntry OBJECT-TYPE SYNTAX QosUserPriEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User Priority to Traffic Class mapping." INDEX {qosUserPriIndex } ::= { qosUserPriorityTable 1 } QosUserPriEntry ::= SEQUENCE { qosUserPriIndex INTEGER, qosUserPriClass INTEGER } qosUserPriIndex OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "For ingress tagged packets, D-Link Smart Switches will refer to these information and prioritize them with 4 different priority queues. If 802.1p is enabled." ::= { qosUserPriEntry 1 } qosUserPriClass OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The User Class the received frame is mapped to." ::= { qosUserPriEntry 2 } --7 priority setting on/off table -- qosPriSettings OBJECT IDENTIFIER ::= { companyQoSGroup 7 } qosPriSettingsTable OBJECT-TYPE SYNTAX SEQUENCE OF QosPriSettingsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of port priority settings." REFERENCE "ISO/IEC 15802-3 Table 7-2" ::= { qosPriSettings 1 } qosPriSettingsEntry OBJECT-TYPE SYNTAX QosPriSettingsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of port priority settings Entries." INDEX {qosPriSetPortIndex } ::= { qosPriSettingsTable 1 } QosPriSettingsEntry ::= SEQUENCE { qosPriSetPortIndex INTEGER, qosPriSetPortType INTEGER } qosPriSetPortIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "A port identifier that is in the range of 1 to ifNumber." ::= { qosPriSettingsEntry 1 } qosPriSetPortType OBJECT-TYPE SYNTAX INTEGER { none(0), ieee8021P(2), dscp-tos(4), ieee8021P_dscp-tos(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "The port priority setting type. (ex. none = 0, 802.1p = 2, DSCP = 4. If you want enable 802.1p & DSCP, the value is 2 + 4 = 6. " ::= { qosPriSettingsEntry 2 } -- ------------------------------------------------------------------ -- QoS -- ------------------------------------------------------------------ qosDiffServTOS OBJECT IDENTIFIER ::= { companyQoSGroup 6 } qosDSCPTOSMode OBJECT-TYPE SYNTAX INTEGER { tos(1), dscp(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Settings of Qos mode: DSCP QoS or TOS Qos. IEEE 802.1p : It specifies a priority(0~7) value to four queues in WS3 : Low(1,2), Medium(0,3), High(4,5) and Highest(6,7), inclusive that can be used by Quality of Service (QoS) disciplines to differentiate traffic. DSCP : Differentiated services enhancements to the Internet protocol are intended to enable scalable service discrimination in the Internet without the need for per-flow state and signaling at every hop. " ::= { qosDiffServTOS 1 } -- ------------------------------------------------------------------ -- DSCP_Mode -- ------------------------------------------------------------------ qosDiffServTypeGroup OBJECT IDENTIFIER ::= { qosDiffServTOS 2 } qosDiffServType00 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 0 : IP ToS value = 0" ::= { qosDiffServTypeGroup 1 } qosDiffServType01 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 01 : IP ToS value = 4" ::= { qosDiffServTypeGroup 2 } qosDiffServType02 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 02 : IP ToS value = 8" ::= { qosDiffServTypeGroup 3 } qosDiffServType03 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 03 : IP ToS value = 12" ::= { qosDiffServTypeGroup 4 } qosDiffServType04 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 04 : IP ToS value = 16" ::= { qosDiffServTypeGroup 5 } qosDiffServType05 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 05 : IP ToS value = 20" ::= { qosDiffServTypeGroup 6 } qosDiffServType06 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 06 : IP ToS value = 24" ::= { qosDiffServTypeGroup 7 } qosDiffServType07 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 07 : IP ToS value = 28" ::= { qosDiffServTypeGroup 8 } qosDiffServType08 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 08 : IP ToS value = 32" ::= { qosDiffServTypeGroup 9 } qosDiffServType09 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 09 : IP ToS value = 36" ::= { qosDiffServTypeGroup 10 } qosDiffServType10 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 10 : IP ToS value = 40" ::= { qosDiffServTypeGroup 11 } qosDiffServType11 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 11 : IP ToS value = 44" ::= { qosDiffServTypeGroup 12 } qosDiffServType12 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 12 : IP ToS value = 48" ::= { qosDiffServTypeGroup 13 } qosDiffServType13 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 13 : IP ToS value = 52" ::= { qosDiffServTypeGroup 14 } qosDiffServType14 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 14 : IP ToS value = 56" ::= { qosDiffServTypeGroup 15 } qosDiffServType15 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 15 : IP ToS value = 60" ::= { qosDiffServTypeGroup 16 } qosDiffServType16 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 16 : IP ToS value = 64" ::= { qosDiffServTypeGroup 17 } qosDiffServType17 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 17 : IP ToS value = 68" ::= { qosDiffServTypeGroup 18 } qosDiffServType18 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 18 : IP ToS value = 72" ::= { qosDiffServTypeGroup 19 } qosDiffServType19 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 19 : IP ToS value = 76" ::= { qosDiffServTypeGroup 20 } qosDiffServType20 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 20 : IP ToS value = 80" ::= { qosDiffServTypeGroup 21 } qosDiffServType21 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 21 : IP ToS value = 84" ::= { qosDiffServTypeGroup 22 } qosDiffServType22 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 22 : IP ToS value = 88" ::= { qosDiffServTypeGroup 23 } qosDiffServType23 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 23 : IP ToS value = 92" ::= { qosDiffServTypeGroup 24 } qosDiffServType24 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 24 : IP ToS value = 96" ::= { qosDiffServTypeGroup 25 } qosDiffServType25 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 25 : IP ToS value = 100" ::= { qosDiffServTypeGroup 26 } qosDiffServType26 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 26 : IP ToS value = 104" ::= { qosDiffServTypeGroup 27 } qosDiffServType27 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 27 : IP ToS value = 108" ::= { qosDiffServTypeGroup 28 } qosDiffServType28 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 28 : IP ToS value = 112" ::= { qosDiffServTypeGroup 29 } qosDiffServType29 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 29 : IP ToS value = 116" ::= { qosDiffServTypeGroup 30 } qosDiffServType30 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 30 : IP ToS value = 120" ::= { qosDiffServTypeGroup 31 } qosDiffServType31 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 31 : IP ToS value = 124" ::= { qosDiffServTypeGroup 32 } qosDiffServType32 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 32 : IP ToS value = 128" ::= { qosDiffServTypeGroup 33 } qosDiffServType33 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 33 : IP ToS value = 132" ::= { qosDiffServTypeGroup 34 } qosDiffServType34 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 34 : IP ToS value = 136" ::= { qosDiffServTypeGroup 35 } qosDiffServType35 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 35 : IP ToS value = 140" ::= { qosDiffServTypeGroup 36 } qosDiffServType36 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 36 : IP ToS value = 144" ::= { qosDiffServTypeGroup 37 } qosDiffServType37 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 37 : IP ToS value = 148" ::= { qosDiffServTypeGroup 38 } qosDiffServType38 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 38 : IP ToS value = 152" ::= { qosDiffServTypeGroup 39 } qosDiffServType39 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 39 : IP ToS value = 156" ::= { qosDiffServTypeGroup 40 } qosDiffServType40 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 40 : IP ToS value = 160" ::= { qosDiffServTypeGroup 41 } qosDiffServType41 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 41 : IP ToS value = 164" ::= { qosDiffServTypeGroup 42 } qosDiffServType42 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 42 : IP ToS value = 168" ::= { qosDiffServTypeGroup 43 } qosDiffServType43 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 43 : IP ToS value = 172" ::= { qosDiffServTypeGroup 44 } qosDiffServType44 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 44 : IP ToS value = 176" ::= { qosDiffServTypeGroup 45 } qosDiffServType45 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 45 : IP ToS value = 180" ::= { qosDiffServTypeGroup 46 } qosDiffServType46 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 46 : IP ToS value = 184" ::= { qosDiffServTypeGroup 47 } qosDiffServType47 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 47 : IP ToS value = 188" ::= { qosDiffServTypeGroup 48 } qosDiffServType48 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 48 : IP ToS value = 192" ::= { qosDiffServTypeGroup 49 } qosDiffServType49 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 49 : IP ToS value = 196" ::= { qosDiffServTypeGroup 50 } qosDiffServType50 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 50 : IP ToS value = 200" ::= { qosDiffServTypeGroup 51 } qosDiffServType51 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 51 : IP ToS value = 204" ::= { qosDiffServTypeGroup 52 } qosDiffServType52 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 52 : IP ToS value = 208" ::= { qosDiffServTypeGroup 53 } qosDiffServType53 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 53 : IP ToS value = 212" ::= { qosDiffServTypeGroup 54 } qosDiffServType54 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 54 : IP ToS value = 216" ::= { qosDiffServTypeGroup 55 } qosDiffServType55 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 55 : IP ToS value = 220" ::= { qosDiffServTypeGroup 56 } qosDiffServType56 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 56 : IP ToS value = 224" ::= { qosDiffServTypeGroup 57 } qosDiffServType57 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 57 : IP ToS value = 228" ::= { qosDiffServTypeGroup 58 } qosDiffServType58 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 58 : IP ToS value = 232" ::= { qosDiffServTypeGroup 59 } qosDiffServType59 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 59 : IP ToS value = 236" ::= { qosDiffServTypeGroup 60 } qosDiffServType60 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 60 : IP ToS value = 240" ::= { qosDiffServTypeGroup 61 } qosDiffServType61 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 61 : IP ToS value = 244" ::= { qosDiffServTypeGroup 62 } qosDiffServType62 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 62 : IP ToS value = 248" ::= { qosDiffServTypeGroup 63 } qosDiffServType63 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "DiffServ Type 63 : IP ToS value = 252" ::= { qosDiffServTypeGroup 64 } -- ------------------------------------------------------------------ -- TOS_Mode -- ------------------------------------------------------------------ qosTOSGroup OBJECT IDENTIFIER ::= { qosDiffServTOS 3 } qosTOSType00 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 0" ::= { qosTOSGroup 1 } qosTOSType01 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 01" ::= { qosTOSGroup 2 } qosTOSType02 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 02" ::= { qosTOSGroup 3 } qosTOSType03 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 03" ::= { qosTOSGroup 4 } qosTOSType04 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 04" ::= { qosTOSGroup 5 } qosTOSType05 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 05" ::= { qosTOSGroup 6 } qosTOSType06 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 06" ::= { qosTOSGroup 7 } qosTOSType07 OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "TOS 07" ::= { qosTOSGroup 8 } qosAclPrioritySettings OBJECT IDENTIFIER ::= { companyQoSGroup 8 } -- ------------------------------------------------------------------ -- ipv4aclQosTable -- ------------------------------------------------------------------ ipv4aclQosTable OBJECT-TYPE SYNTAX SEQUENCE OF Ipv4AclQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of priority by acl setting." ::= { qosAclPrioritySettings 1 } ipv4aclQosEntry OBJECT-TYPE SYNTAX Ipv4AclQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of priority by acl setting entry." INDEX { ipv4aclQosIndex } ::= { ipv4aclQosTable 1 } Ipv4AclQosEntry ::= SEQUENCE { ipv4aclQosIndex Integer32, ipv4aclQosType INTEGER, ipv4aclQosMACAddr MacAddress, ipv4aclQosIPAddr IpAddress, ipv4aclQosTCPUDPPort Integer32, ipv4aclQosVlanID Integer32, ipv4aclQosProtocol Integer32, ipv4aclQosAssignClass INTEGER, ipv4aclQosStatus RowStatus } ipv4aclQosIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Index of priority by acl setting." ::= { ipv4aclQosEntry 1 } ipv4aclQosType OBJECT-TYPE SYNTAX INTEGER { mac(0), ip(1), tcp(2), udp(3), vlanid(4), protocol(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of priority by acl setting." ::= { ipv4aclQosEntry 2 } ipv4aclQosMACAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Dst MAC of priority by acl setting." ::= { ipv4aclQosEntry 3 } ipv4aclQosIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Dst IP of priority by acl setting" ::= { ipv4aclQosEntry 4 } ipv4aclQosTCPUDPPort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Dst TCP/UDP port of priority by acl setting" ::= { ipv4aclQosEntry 5 } ipv4aclQosVlanID OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VLAN ID of priority by acl setting" ::= { ipv4aclQosEntry 6 } ipv4aclQosProtocol OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Ip protocol number of priority by acl setting" ::= { ipv4aclQosEntry 7 } ipv4aclQosAssignClass OBJECT-TYPE SYNTAX INTEGER { class0(0), class1(1), class2(2), class3(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Be mapped class of priority by acl setting." ::= { ipv4aclQosEntry 8 } ipv4aclQosStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Status of priority by acl setting." ::= { ipv4aclQosEntry 9 } -- ------------------------------------------------------------------ -- aclQosTable -- ------------------------------------------------------------------ aclQosTable OBJECT-TYPE SYNTAX SEQUENCE OF AclQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of priority by acl setting." ::= { qosAclPrioritySettings 2 } aclQosEntry OBJECT-TYPE SYNTAX AclQosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of priority by acl setting entry." INDEX { aclQosIndex } ::= { aclQosTable 1 } AclQosEntry ::= SEQUENCE { aclQosIndex Integer32, aclQosType INTEGER, aclQosMACAddr MacAddress, aclQosIPAddr IpAddress, aclQosIPv6Addr Ipv6Address, aclQosTCPUDPPort Integer32, aclQosVlanID Integer32, aclQosProtocol Integer32, --start DLINK_METRO_LIKE_R25QOS_BY_IPV6_TC_ACL aclQosIP6TC Integer32, --end DLINK_METRO_LIKE_R25QOS_BY_IPV6_TC_ACL aclQosAssignClass INTEGER, aclQosStatus RowStatus } aclQosIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Index of priority by acl setting." ::= { aclQosEntry 1 } aclQosType OBJECT-TYPE SYNTAX INTEGER { mac(0), ip(1), tcp(2), udp(3), vlanid(4), protocol(5), ipv6(6), ipv6traffic_class(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of priority by acl setting." ::= { aclQosEntry 2 } aclQosMACAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Dst MAC of priority by acl setting." ::= { aclQosEntry 3 } aclQosIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Dst IP of priority by acl setting" ::= { aclQosEntry 4 } aclQosIPv6Addr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "Dst IP of priority by acl setting. " ::= { aclQosEntry 5 } aclQosTCPUDPPort OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Dst TCP/UDP port of priority by acl setting" ::= { aclQosEntry 6 } aclQosVlanID OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "VLAN ID of priority by acl setting" ::= { aclQosEntry 7 } aclQosProtocol OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Ip protocol number of priority by acl setting" ::= { aclQosEntry 8 } --start DLINK_METRO_LIKE_R25QOS_BY_IPV6_TC_ACL aclQosIP6TC OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Ipv6 Traffic Class number of priority by acl setting" ::= { aclQosEntry 10 } --end DLINK_METRO_LIKE_R25QOS_BY_IPV6_TC_ACL aclQosAssignClass OBJECT-TYPE SYNTAX INTEGER { class0(0), class1(1), class2(2), class3(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Be mapped class of priority by acl setting." ::= { aclQosEntry 98 } aclQosStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Status of priority by acl setting." ::= { aclQosEntry 99 } -- ---------------------------------------------------------- -- The companyTrafficMgmt Groups -- ---------------------------------------------------------- -- Bandwidth Control Group --------------------------------------------- -- bandwidthCtrlSettings OBJECT IDENTIFIER ::= { companyTrafficMgmt 1 } bandwidthCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF BandwidthCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control the rate limiting parameters either for the entire switch or for each interface in the switch." ::= { bandwidthCtrlSettings 2 } bandwidthCtrlEntry OBJECT-TYPE SYNTAX BandwidthCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each physical interface in the switch." INDEX { bandwidthCtrlIndex } ::= { bandwidthCtrlTable 1 } BandwidthCtrlEntry ::= SEQUENCE { bandwidthCtrlIndex Integer32, bandwidthCtrlTxThreshold Integer32, bandwidthCtrlRxThreshold Integer32 } bandwidthCtrlIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index for which the configuration in this entry applies." ::= { bandwidthCtrlEntry 1 } bandwidthCtrlTxThreshold OBJECT-TYPE SYNTAX Integer32 (0 | 64..1024000) MAX-ACCESS read-write STATUS current DESCRIPTION "Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000 (Kbits per second) in GE port." ::= { bandwidthCtrlEntry 2 } bandwidthCtrlRxThreshold OBJECT-TYPE SYNTAX Integer32 (0 | 64..1024000) MAX-ACCESS read-write STATUS current DESCRIPTION "Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000(Kbits per second) in GE port." ::= { bandwidthCtrlEntry 3} -- Traffic Control Group --------------------------------------------- -- trafficCtrlSettings OBJECT IDENTIFIER ::= { companyTrafficMgmt 4 } trafficCtrlTrap OBJECT-TYPE SYNTAX INTEGER { none(0), stormOccurred(1), stormCleared(2), both(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The trap setting of traffic control." ::= { trafficCtrlSettings 1 } trafficCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF TrafficCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The traffic control table." ::= { trafficCtrlSettings 2 } trafficCtrlEntry OBJECT-TYPE SYNTAX TrafficCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The traffic control entry." INDEX { trafficCtrlIndex } ::= { trafficCtrlTable 1 } TrafficCtrlEntry ::= SEQUENCE { trafficCtrlIndex Integer32, trafficCtrlActionMode INTEGER, trafficCtrlType INTEGER, trafficCtrlThreshold Integer32, trafficCtrlCountDown Integer32, trafficCtrlTimeInterval Integer32 } trafficCtrlIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The traffic control index." ::= { trafficCtrlEntry 1 } trafficCtrlActionMode OBJECT-TYPE SYNTAX INTEGER { drop(0), shutdown(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The action mode of traffic control." ::= { trafficCtrlEntry 2 } trafficCtrlType OBJECT-TYPE SYNTAX INTEGER { none(0), b(1), m(2), mb(3), u(4), ub(5), um(6), umb(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The control type of traffic control. (b: Broadcast, m: Multicast, u: Unknown Unicast)" ::= { trafficCtrlEntry 3 } trafficCtrlThreshold OBJECT-TYPE SYNTAX Integer32 (1..102400) MAX-ACCESS read-write STATUS current DESCRIPTION "The threshold of traffic control." ::= { trafficCtrlEntry 4 } trafficCtrlCountDown OBJECT-TYPE SYNTAX Integer32 (0..30) MAX-ACCESS read-write STATUS current DESCRIPTION "The count down value of traffic control." ::= { trafficCtrlEntry 5 } trafficCtrlTimeInterval OBJECT-TYPE SYNTAX Integer32 (5..30) MAX-ACCESS read-write STATUS current DESCRIPTION "The time interval of traffic control." ::= { trafficCtrlEntry 6 } -- ------------------------------------------------------------------ -- companySecurity -- ------------------------------------------------------------------ -- Trusted Host securityTrustedHost OBJECT IDENTIFIER ::= { companySecurity 1 } trustedHostStatus OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which you trust to access and control the switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection." DEFVAL { disabled } ::= { securityTrustedHost 1 } ipv4trustedHostTable OBJECT-TYPE SYNTAX SEQUENCE OF Ipv4TrustedHostEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A table to configure trusted host in the system." ::= { securityTrustedHost 2 } ipv4trustedHostEntry OBJECT-TYPE SYNTAX Ipv4TrustedHostEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "Each entry in this table represents rules for particular trusted host." INDEX { ipv4trustedHostIpAddr, ipv4trustedHostIpMask } ::= { ipv4trustedHostTable 1 } Ipv4TrustedHostEntry ::= SEQUENCE { ipv4trustedHostIpAddr IpAddress, ipv4trustedHostIpMask IpAddress, ipv4trustedHostRowStatus RowStatus } ipv4trustedHostIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection." ::= { ipv4trustedHostEntry 1 } ipv4trustedHostIpMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS obsolete DESCRIPTION "Used to mask with IP address, it allow you set a subnet as a trusted host entry." ::= { ipv4trustedHostEntry 2 } ipv4trustedHostRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS obsolete DESCRIPTION "The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available." ::= { ipv4trustedHostEntry 3 } -- ipv6 trustedHostTable OBJECT-TYPE SYNTAX SEQUENCE OF TrustedHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to configure trusted host for in the system." ::= { securityTrustedHost 3 } trustedHostEntry OBJECT-TYPE SYNTAX TrustedHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents rules for particular trusted host." INDEX { trustedHostIPType, trustedHostIpAddr, trustedHostIpMask } ::= { trustedHostTable 1 } TrustedHostEntry ::= SEQUENCE { trustedHostIPType INTEGER, trustedHostIpAddr Ipv6Address, trustedHostIpMask Ipv6Address, trustedHostRowStatus RowStatus } trustedHostIPType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of IP interface." ::= { trustedHostEntry 1 } trustedHostIpAddr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of host you allow to access to D-Link Smart Switch. Your local host IPv4/6 Addresses must be one of the IP Addresses to avoid disconnection." ::= { trustedHostEntry 2 } trustedHostIpMask OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "Used to mask with IPv4/6 address, it allow you set a subnet as a trusted host entry." ::= { trustedHostEntry 3 } trustedHostRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available." ::= { trustedHostEntry 4 } securityARPSpoofPrevent OBJECT IDENTIFIER ::= { companySecurity 3} -- aRPSpoofPrevent Control Table aRPSpoofPreventTable OBJECT-TYPE SYNTAX SEQUENCE OF ARPSpoofPreventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control ARP Spoofing prevention for the entire switch or for each interface in the switch." ::= { securityARPSpoofPrevent 1 } aRPSpoofPreventEntry OBJECT-TYPE SYNTAX ARPSpoofPreventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system." INDEX { aRPSpoofPreventIpAddr } ::= { aRPSpoofPreventTable 1 } ARPSpoofPreventEntry ::= SEQUENCE { aRPSpoofPreventIpAddr IpAddress, aRPSpoofPreventMacAddress MacAddress, aRPSpoofPreventPortList PortList, aRPSpoofPreventRowStatus RowStatus } aRPSpoofPreventIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'." ::= { aRPSpoofPreventEntry 1 } aRPSpoofPreventMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Ethernet Mac Address." DEFVAL { '000102030405'h } ::= { aRPSpoofPreventEntry 2 } aRPSpoofPreventPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports." ::= { aRPSpoofPreventEntry 3 } aRPSpoofPreventRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { aRPSpoofPreventEntry 4 } -- ------------------------------------------------------------------ -- companySecurity -- ------------------------------------------------------------------ securitySSL OBJECT IDENTIFIER ::= { companySecurity 5 } sslSecurityHttpStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling secure HTTP in the system." DEFVAL { disable } ::= { securitySSL 1 } sslCiphers OBJECT IDENTIFIER ::= { securitySSL 2 } sslCipherSuiteList OBJECT-TYPE SYNTAX BITS { rsa-null-md5(0), rsa-null-sha(1), rsa-des-sha(2), rsa-3des-sha(3), dh-rsa-des-sha(4), dh-rsa-3des-sha(5), rsa-exp1024-des-sha(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is to configure the cipher-suites list." ::= { sslCiphers 1} -- ------------------------------------------------------------------ -- companySecurity -- ------------------------------------------------------------------ securitySSH OBJECT IDENTIFIER ::= { companySecurity 8 } sshSecurityStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling ssh in the system." DEFVAL { disable } ::= { securitySSH 1} sshMaxAuthFailAttempts OBJECT-TYPE SYNTAX INTEGER (2..20) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the max auth fail retry attempt times." ::= {securitySSH 2} sshSessionKeyRekeying OBJECT-TYPE SYNTAX INTEGER { never(0), ten-min(1), thirty-min(2), sixty-min(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates one SSH session rekey time interval." ::= {securitySSH 3} sshMaxSession OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates max SSH session number supported in system." ::= {securitySSH 4} sshConnectionTimeout OBJECT-TYPE SYNTAX INTEGER (120..600) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates SSH connection timeout value." ::= {securitySSH 5} --************************************************************************ -- SSH encryption algorithm group configuration --************************************************************************ sshAuthenMethodPassWordAdmin OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object indicates authen method password is enabled or disabled." ::= {securitySSH 6} sshAuthenMethodPubKeyAdmin OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object indicates authen method public-key is enabled or disabled." ::= {securitySSH 7} sshAuthenMethodHostKeyAdmin OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object indicates authen method host-key is enabled or disabled." ::= {securitySSH 8} sshCipherSuiteList OBJECT-TYPE SYNTAX BITS { tripleDESCBC(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object is to configure the cipher-suites list." ::= { securitySSH 9} sshMacSuiteList OBJECT-TYPE SYNTAX BITS { hMAC-SHA1(0), hMAC-MD5(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is to configure the MAC-list." ::= { securitySSH 10} sshPublKeyRSAAdmin OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object indicates Public key generating algorithm RSA is enabled or disabled." ::= {securitySSH 11} --************************************************************************ -- SSH User Auth Info. --************************************************************************ sshUserInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF SshUserInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to configure SSH user auth in the system." ::= { securitySSH 12 } sshUserInfoEntry OBJECT-TYPE SYNTAX SshUserInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry to configure user auth in the system." INDEX { sshUserInfoID } ::= { sshUserInfoTable 1 } SshUserInfoEntry ::= SEQUENCE { sshUserInfoID Integer32, sshUserInfoUserName DisplayString, sshUserInfoAuth INTEGER, sshUserInfoHostName DisplayString, sshUserInfoHostIp IpAddress } sshUserInfoID OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS read-only STATUS current DESCRIPTION "The Schedule identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 8." ::= { sshUserInfoEntry 1 } sshUserInfoUserName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The ssh user name associated with the SSH suer Info. entry (e.g., `admin, user')." ::= { sshUserInfoEntry 2} sshUserInfoAuth OBJECT-TYPE SYNTAX INTEGER { publickey(4), password(2), hostbased(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object indicates which auth used by the user." ::= {sshUserInfoEntry 3} sshUserInfoHostName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The ssh host name associated with the SSH suer Info. entry (e.g., `DUT1, DUT2')." ::= { sshUserInfoEntry 4} sshUserInfoHostIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "SSH HostBased IP Address of the system." ::= { sshUserInfoEntry 5 } -- ---------------------------------------------------------- -- The companySecurity Groups -- ---------------------------------------------------------- securityPortSecurity OBJECT IDENTIFIER ::= { companySecurity 2 } -- Port Security Group --------------------------------------------- -- portSecTable OBJECT-TYPE SYNTAX SEQUENCE OF PortSecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control port security features of the device." ::= { securityPortSecurity 1 } portSecEntry OBJECT-TYPE SYNTAX PortSecEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in port security table for each interface in the system." INDEX { portSecIndex } ::= { portSecTable 1 } PortSecEntry ::= SEQUENCE { portSecIndex Integer32, portSecState INTEGER, portSecMLA Integer32 -- start DLINK_METRO_LIKE_LOCK_ADDRESS_MODE , portSecLockAddrMode INTEGER -- end DLINK_METRO_LIKE_LOCK_ADDRESS_MODE } portSecIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index for which the configuration in this entry applies." ::= { portSecEntry 1 } portSecState OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled." ::= { portSecEntry 2 } portSecMLA OBJECT-TYPE SYNTAX Integer32 (0..64) MAX-ACCESS read-write STATUS current DESCRIPTION "Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number. The number can be set 0 to 64. Note: Set value 0 means cannot learn MAC address." ::= {portSecEntry 3} -- start DLINK_METRO_LIKE_LOCK_ADDRESS_MODE portSecLockAddrMode OBJECT-TYPE SYNTAX INTEGER { deleteOnReset (1), deleteOnTimeout (2), permanent(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures port security lock address mode for the interface. deleteOnReset : The locked addresses will not age out until the Switch has been reset. deleteOnTimeout : The locked addresses will age out after the aging timer expires. Permanent : The locked addresses will not age out after the aging timer expires." ::= { portSecEntry 4 } portSecFDBPermanentTable OBJECT-TYPE SYNTAX SEQUENCE OF PortSecFDBPermanentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control port security FDB Permanent of the device." ::= { securityPortSecurity 2 } portSecFDBPermanentEntry OBJECT-TYPE SYNTAX PortSecFDBPermanentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in port security table for each interface in the system." INDEX { portSecFDBPermPort, portSecFDBPermIndex} ::= { portSecFDBPermanentTable 1 } PortSecFDBPermanentEntry ::= SEQUENCE { portSecFDBPermIndex INTEGER, portSecFDBPermVlanID INTEGER, portSecFDBPermMac MacAddress, portSecFDBPermPort INTEGER } portSecFDBPermIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port security MAC entry." ::= { portSecFDBPermanentEntry 1 } portSecFDBPermVlanID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the port security MAC entry." ::= { portSecFDBPermanentEntry 2 } portSecFDBPermMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the port security MAC entry." ::= { portSecFDBPermanentEntry 3 } portSecFDBPermPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The forwarding port of the port security MAC entry." ::= { portSecFDBPermanentEntry 4 } -- end DLINK_METRO_LIKE_LOCK_ADDRESS_MODE -- ---------------------------------------------------------- -- The companyCableDiagnostic Groups -- ---------------------------------------------------------- -- Cable Diagnostics Group --------------------------------------------- -- cableDiagTable OBJECT-TYPE SYNTAX SEQUENCE OF CableDiagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the cable situation for each port." ::= {companyCableDiagnostic 1 } cableDiagEntry OBJECT-TYPE SYNTAX CableDiagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of cable situations for each port on the device." INDEX { cableDiagPortIndex } ::= { cableDiagTable 1 } CableDiagEntry ::= SEQUENCE { cableDiagPortIndex Integer32, cableDiagPortType INTEGER, cableDiagLinkStatus INTEGER, cableDiagPair1Status INTEGER, cableDiagPair2Status INTEGER, cableDiagPair3Status INTEGER, cableDiagPair4Status INTEGER, cableDiagPair1Length Integer32, cableDiagPair2Length Integer32, cableDiagPair3Length Integer32, cableDiagPair4Length Integer32, cableDiagAction INTEGER, cableDiagStatus INTEGER } cableDiagPortIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index for which the configuration in this entry applies." ::= { cableDiagEntry 1 } cableDiagPortType OBJECT-TYPE SYNTAX INTEGER { fastEthernet(0), gigaEthernet(1), other(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the supported port data rate classification." ::= { cableDiagEntry 2 } cableDiagLinkStatus OBJECT-TYPE SYNTAX INTEGER { linkdown(0), linkup(1), other(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the link status." ::= { cableDiagEntry 3 } cableDiagPair1Status OBJECT-TYPE SYNTAX INTEGER { ok(0), open(1), short(2), open-short(3), crosstalk(4), unknown(5), count(6), no-cable(7), other(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 1 test result." ::= {cableDiagEntry 4 } cableDiagPair2Status OBJECT-TYPE SYNTAX INTEGER { ok(0), open(1), short(2), open-short(3), crosstalk(4), unknown(5), count(6), no-cable(7), other(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 2 test result." ::= {cableDiagEntry 5 } cableDiagPair3Status OBJECT-TYPE SYNTAX INTEGER { ok(0), open(1), short(2), open-short(3), crosstalk(4), unknown(5), count(6), no-cable(7), other(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 3 test result." ::= {cableDiagEntry 6 } cableDiagPair4Status OBJECT-TYPE SYNTAX INTEGER { ok(0), open(1), short(2), open-short(3), crosstalk(4), unknown(5), count(6), no-cable(7), other(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 4 test result." ::= {cableDiagEntry 7} cableDiagPair1Length OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Cable Diagnostics pair 1 fault distance." ::= {cableDiagEntry 8} cableDiagPair2Length OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 2 fault distance." ::= {cableDiagEntry 9} cableDiagPair3Length OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 3 fault distance." ::= {cableDiagEntry 10} cableDiagPair4Length OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Cable diagnostics pair 4 fault distance." ::= {cableDiagEntry 11} cableDiagAction OBJECT-TYPE SYNTAX INTEGER { action(1), processing(2), other(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Function to run the cable diagnostic on selected port. Can not detect fiber ports" ::= { cableDiagEntry 12} cableDiagStatus OBJECT-TYPE SYNTAX INTEGER { notrun(1), processing(2), lasttestok(3), lasttestfailed(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the status of cable diagnostics on the port. not-run - cable diagnostics has never been run for this port processing - cable diagnostics is currently running on the port last-test-ok - the last cable diagnostics done on the port was successful last-test-failed - the last cable diagnostics done on the port failed" ::= { cableDiagEntry 13 } -- ------------------------------------------------------------------ -- companyACLGroup -- ------------------------------------------------------------------ -- ACL Profile Group -------------------------------------------------- aclProfile OBJECT IDENTIFIER ::= { companyACLGroup 1 } ipv4aclProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF Ipv4AclProfileEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION " A table to ACL profile . " ::= { aclProfile 1 } ipv4aclProfileEntry OBJECT-TYPE SYNTAX Ipv4AclProfileEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION " Each entry in this table is a ACL profile. Index to the table is ACL profile ID. " INDEX { ipv4aclProfileNo} ::= { ipv4aclProfileTable 1 } Ipv4AclProfileEntry ::= SEQUENCE { ipv4aclProfileNo Integer32, ipv4aclProfileType INTEGER, ipv4aclProfileRuleCount Integer32, ipv4aclProfileMask OCTET STRING, ipv4aclProfileDstMacAddrMask MacAddress, ipv4aclProfileSrcMacAddrMask MacAddress, ipv4aclProfileIPProtocol INTEGER, ipv4aclProfileIPProtocolMask OCTET STRING, ipv4aclProfileDstIpAddrMask IpAddress, ipv4aclProfileSrcIpAddrMask IpAddress, ipv4aclProfileDstPortMask OCTET STRING, ipv4aclProfileSrcPortMask OCTET STRING, ipv4aclProfileArpSenderMacAddrMask MacAddress, ipv4aclProfileArpSenderIpAddrMask IpAddress, ipv4aclProfileUdfOffsetMap OCTET STRING, ipv4aclUdfOffsetChunk1 Integer32, ipv4aclUdfOffsetMask1 OCTET STRING, ipv4aclUdfOffsetChunk2 Integer32, ipv4aclUdfOffsetMask2 OCTET STRING, ipv4aclUdfOffsetChunk3 Integer32, ipv4aclUdfOffsetMask3 OCTET STRING, ipv4aclUdfOffsetChunk4 Integer32, ipv4aclUdfOffsetMask4 OCTET STRING, ipv4aclProfileStatus RowStatus } ipv4aclProfileNo OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only." ::= { ipv4aclProfileEntry 1 } ipv4aclProfileType OBJECT-TYPE SYNTAX INTEGER { l2 (1), l3 (2), impb (3), arpSP_permit(4), arpSP_deny(5), aclQos (8) , userDefined(9) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, arpSP_permit(4) - for ARP Spoofing prevention entry, arpSP_deny(5) - for ARP Spoofing prevention entry, voiceVlan(6) - for Voice VLAN OUI entry. userDefined(9) - for User Defined entry. Note that only l2, l3 and userDefined could be set by user, other is reserved for system to show information. " ::= { ipv4aclProfileEntry 2 } ipv4aclProfileRuleCount OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The number of rules in this profile." ::= { ipv4aclProfileEntry 3 } ipv4aclProfileMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID 2 L2 8021P_PRIORITY 3 L2 ETHER_TYPE 4 L3 DSCP 5 L3 ICMP_TYPE 6 L3 ICMP_CODE 7 L3 IGMP_TYPE 8 L3 DST_IP 9 L3 SRC_IP 10 L3 DST_PORT 11 L3 SRC_PORT 12 L3 TCPFLAG 13 ARP-SP ARP_SENDER_MAC 14 ARP-SP ARP_SENDER_IP 15 L3 TOS 16 UDF UDF1 17 UDF UDF2 18 UDF UDF3 19 UDF UDF4 20 L3v6 TRAFFIC_CLASS 21 L3v6 DST_IPV6 22 L3v6 SRC_IPV6 23 (MSB) ------------------------------------------- The value is in Hex format. " ::= { ipv4aclProfileEntry 4 } ipv4aclProfileDstMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The ACL Profile destination MAC address mask. If DST_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate a range of MAC address which is really care. " ::= { ipv4aclProfileEntry 5 } ipv4aclProfileSrcMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The ACL Profile source MAC address mask. If SRC_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a range of MAC address which is really care. " ::= { ipv4aclProfileEntry 6 } ipv4aclProfileIPProtocol OBJECT-TYPE SYNTAX INTEGER { none(0), icmp(1), igmp(2), tcp(6), udp(17), icmpv6(58) ,ipProtocolMask(256) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. " ::= { ipv4aclProfileEntry 7 } ipv4aclProfileIPProtocolMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The ACL Profile IP protocol mask. If aclProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format. " DEFVAL { 'FF'h } ::= { ipv4aclProfileEntry 8 } ipv4aclProfileDstIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The ACL Profile destination IP address mask. If DST_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00' " DEFVAL { 'FFFFFFFF'h } ::= { ipv4aclProfileEntry 9 } ipv4aclProfileSrcIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The ACL Profile source IP address mask. If SRC_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00' " DEFVAL { 'FFFFFFFF'h } ::= { ipv4aclProfileEntry 10 } ipv4aclProfileDstPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The ACL Profile UDP/TCP destination port mask. If DST_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format. " DEFVAL { 'FFFF'h } ::= { ipv4aclProfileEntry 11 } ipv4aclProfileSrcPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The ACL Profile UDP/TCP source port mask. If SRC_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format. " DEFVAL { 'FFFF'h } ::= { ipv4aclProfileEntry 12 } ipv4aclProfileArpSenderMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format. " DEFVAL { 'FFFFFFFFFF'h } ::= { ipv4aclProfileEntry 13 } ipv4aclProfileArpSenderIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format. " DEFVAL { 'FFFFFFFF'h } ::= { ipv4aclProfileEntry 14 } ipv4aclProfileUdfOffsetMap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Indicate which Udf field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ UDF Offset1 0 (LSB) UDF Offset2 1 UDF Offset3 2 UDF Offset4 3 ------------------------------------------- The value is in Hex format. " ::= { ipv4aclProfileEntry 15 } ipv4aclUdfOffsetChunk1 OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The value of offset Chunk." ::= { ipv4aclProfileEntry 17 } ipv4aclUdfOffsetMask1 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The value of offset MAsk." DEFVAL { 'FFFFFFFF'h } ::= { ipv4aclProfileEntry 18 } ipv4aclUdfOffsetChunk2 OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The value of offset Chunk." ::= { ipv4aclProfileEntry 20 } ipv4aclUdfOffsetMask2 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The value of offset MAsk." DEFVAL { 'FFFFFFFF'h } ::= { ipv4aclProfileEntry 21 } ipv4aclUdfOffsetChunk3 OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The value of offset Chunk." ::= { ipv4aclProfileEntry 23 } ipv4aclUdfOffsetMask3 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The value of offset MAsk." DEFVAL { 'FFFFFFFF'h } ::= { ipv4aclProfileEntry 24 } ipv4aclUdfOffsetChunk4 OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The value of offset Chunk." ::= { ipv4aclProfileEntry 26 } ipv4aclUdfOffsetMask4 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The value of offset MAsk." DEFVAL { 'FFFFFFFF'h } ::= { ipv4aclProfileEntry 27 } ipv4aclProfileStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS obsolete DESCRIPTION " This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted. " ::= { ipv4aclProfileEntry 28 } -- IPv6 ACL Profile Group -------------------------------------------------- aclProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AclProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A table to ACL profile . " ::= { aclProfile 2 } aclProfileEntry OBJECT-TYPE SYNTAX AclProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Each entry in this table is a ACL profile. Index to the table is ACL profile ID. " INDEX { aclProfileNo} ::= { aclProfileTable 1 } AclProfileEntry ::= SEQUENCE { aclProfileNo Integer32, aclProfileType INTEGER, aclProfileRuleCount Integer32, aclProfileMask OCTET STRING, aclProfileDstMacAddrMask MacAddress, aclProfileSrcMacAddrMask MacAddress, aclProfileIPProtocol INTEGER, aclProfileIPProtocolMask OCTET STRING, aclProfileDstIpAddrMaskType INTEGER, aclProfileDstIpAddrMask Ipv6Address, aclProfileSrcIpAddrMaskType INTEGER, aclProfileSrcIpAddrMask Ipv6Address, aclProfileDstPortMask OCTET STRING, aclProfileSrcPortMask OCTET STRING, aclProfileArpSenderMacAddrMask MacAddress, aclProfileArpSenderIpAddrMask Ipv6Address, aclProfileUdfOffsetMap OCTET STRING, aclUdfOffsetChunk1 Integer32, aclUdfOffsetMask1 OCTET STRING, aclUdfOffsetChunk2 Integer32, aclUdfOffsetMask2 OCTET STRING, aclUdfOffsetChunk3 Integer32, aclUdfOffsetMask3 OCTET STRING, aclUdfOffsetChunk4 Integer32, aclUdfOffsetMask4 OCTET STRING, aclProfileStatus RowStatus } aclProfileNo OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS read-only STATUS current DESCRIPTION "The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only." ::= { aclProfileEntry 1 } aclProfileType OBJECT-TYPE SYNTAX INTEGER { l2 (1), l3v4 (2), l3v6 (11), impb (3), arpSP_permit(4), arpSP_deny(5), aclQos (8) , userDefined(9) } MAX-ACCESS read-write STATUS current DESCRIPTION "The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3v4 (2) - for IPv4-based rule, l3v6 (11) - for IPv6-based rule, arpSP_permit(4) - for ARP Spoofing prevention entry, arpSP_deny(5) - for ARP Spoofing prevention entry, voiceVlan(6) - for Voice VLAN OUI entry. userDefined(9) - for User Defined entry. Note that only l2, l3 and userDefined could be set by user, other is reserved for system to show information. " ::= { aclProfileEntry 2 } aclProfileRuleCount OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of rules in this profile." ::= { aclProfileEntry 3 } aclProfileMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID 2 L2 8021P_PRIORITY 3 L2 ETHER_TYPE 4 L3 DSCP 5 L3 ICMP_TYPE 6 L3 ICMP_CODE 7 L3 IGMP_TYPE 8 L3 DST_IP 9 L3 SRC_IP 10 L3 DST_PORT 11 L3 SRC_PORT 12 L3 TCPFLAG 13 ARP-SP ARP_SENDER_MAC 14 ARP-SP ARP_SENDER_IP 15 L3 TRAFFIC_CLASS 21 L3 TOS 16 UDF UDF1 17 UDF UDF2 18 UDF UDF3 19 UDF UDF4 20 L3v6 TRAFFIC_CLASS 21 L3v6 DST_IPV6 22 L3v6 SRC_IPV6 23 (MSB) ------------------------------------------- The value is in Hex format. " ::= { aclProfileEntry 4 } aclProfileDstMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The ACL Profile destination MAC address mask. If DST_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate a range of MAC address which is really care. " ::= { aclProfileEntry 5 } aclProfileSrcMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The ACL Profile source MAC address mask. If SRC_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a range of MAC address which is really care. " ::= { aclProfileEntry 6 } aclProfileIPProtocol OBJECT-TYPE SYNTAX INTEGER { none(0), icmp(1), igmp(2), tcp(6), udp(17), icmpv6(58) ,ipProtocolMask(256) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. " ::= { aclProfileEntry 7 } aclProfileIPProtocolMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The ACL Profile IP protocol mask. If aclProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format. " DEFVAL { 'FF'h } ::= { aclProfileEntry 8 } aclProfileDstIpAddrMaskType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "IPv6 Address type." ::= { aclProfileEntry 9 } aclProfileDstIpAddrMask OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The ACL Profile destination IP address mask. If DST_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00' " DEFVAL { 'FFFFFFFF'h } ::= { aclProfileEntry 10 } aclProfileSrcIpAddrMaskType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "IPv6 Address type." ::= { aclProfileEntry 11 } aclProfileSrcIpAddrMask OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The ACL Profile source IP address mask. If SRC_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00' " DEFVAL { 'FFFFFFFF'h } ::= { aclProfileEntry 12 } aclProfileDstPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The ACL Profile UDP/TCP destination port mask. If DST_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format. " DEFVAL { 'FFFF'h } ::= { aclProfileEntry 13 } aclProfileSrcPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The ACL Profile UDP/TCP source port mask. If SRC_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format. " DEFVAL { 'FFFF'h } ::= { aclProfileEntry 14 } aclProfileArpSenderMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format. " DEFVAL { 'FFFFFFFFFF'h } ::= { aclProfileEntry 15 } aclProfileArpSenderIpAddrMask OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format. " DEFVAL { 'FFFFFFFF'h } ::= { aclProfileEntry 16 } aclProfileUdfOffsetMap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Indicate which Udf field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ UDF Offset1 0 (LSB) UDF Offset2 1 UDF Offset3 2 UDF Offset4 3 ------------------------------------------- The value is in Hex format. " ::= { aclProfileEntry 17 } aclUdfOffsetChunk1 OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of offset Chunk." ::= { aclProfileEntry 19 } aclUdfOffsetMask1 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The value of offset MAsk." DEFVAL { 'FFFFFFFF'h } ::= { aclProfileEntry 20 } aclUdfOffsetChunk2 OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of offset Chunk." ::= { aclProfileEntry 22 } aclUdfOffsetMask2 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The value of offset MAsk." DEFVAL { 'FFFFFFFF'h } ::= { aclProfileEntry 23 } aclUdfOffsetChunk3 OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of offset Chunk." ::= { aclProfileEntry 25 } aclUdfOffsetMask3 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The value of offset MAsk." DEFVAL { 'FFFFFFFF'h } ::= { aclProfileEntry 26 } aclUdfOffsetChunk4 OBJECT-TYPE SYNTAX Integer32 (0..31) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of offset Chunk." ::= { aclProfileEntry 28 } aclUdfOffsetMask4 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The value of offset MAsk." DEFVAL { 'FFFFFFFF'h } ::= { aclProfileEntry 29 } aclProfileStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted. " ::= { aclProfileEntry 30 } -- ------------------------------------------------------------------ -- L2 Filter Group -------------------------------------------------- aclL2Rule OBJECT IDENTIFIER ::= { companyACLGroup 2 } aclL2RuleTable OBJECT-TYPE SYNTAX SEQUENCE OF AclL2RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to configure L2 filter rules in the system." ::= { aclL2Rule 1 } aclL2RuleEntry OBJECT-TYPE SYNTAX AclL2RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID." INDEX {aclL2ProfileID, aclL2AccessID} ::= { aclL2RuleTable 1 } AclL2RuleEntry ::= SEQUENCE { aclL2AccessID Integer32, aclL2ProfileID Integer32, aclL2RuleEtherType Integer32, aclL2RuleDstMacAddr MacAddress, aclL2RuleSrcMacAddr MacAddress, aclL2RuleVlanId Integer32, aclL2Rule1pPriority Integer32, aclL2RuleDstMacAddrMask MacAddress, aclL2RuleSrcMacAddrMask MacAddress, aclL2RuleAction INTEGER, aclL2RuleRateLimit Unsigned32, aclL2RuleReplaceDSCP Integer32, aclL2RuleReplace1P Integer32, aclL2RuleReplaceQueue Integer32, aclL2RuleFilterTimeRange OCTET STRING, aclL2RuleInPortList PortList, aclL2RuleInVlanList OCTET STRING, aclL2RuleVlanIdMask OCTET STRING, aclL2RuleStatus RowStatus } aclL2AccessID OBJECT-TYPE SYNTAX Integer32 (0..250) MAX-ACCESS read-only STATUS current DESCRIPTION "L2 Filter rule ID. 0 means auto assign." ::= { aclL2RuleEntry 1 } aclL2ProfileID OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS read-only STATUS current DESCRIPTION "ACL Profile ID which this rule join." DEFVAL { 1 } ::= { aclL2RuleEntry 2 } aclL2RuleEtherType OBJECT-TYPE SYNTAX Integer32 (-1 | 1501..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL2RuleEntry 3 } aclL2RuleDstMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition." ::= { aclL2RuleEntry 4 } aclL2RuleSrcMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address" ::= { aclL2RuleEntry 5 } aclL2RuleVlanId OBJECT-TYPE SYNTAX Integer32 (-1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL2RuleEntry 6 } aclL2Rule1pPriority OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL2RuleEntry 7 } aclL2RuleDstMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting." ::= { aclL2RuleEntry 8 } aclL2RuleSrcMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting." ::= { aclL2RuleEntry 9 } aclL2RuleAction OBJECT-TYPE SYNTAX INTEGER { allow (1) ,drop (2) ,mirror (3) ,rateLimit(4) ,replaceDSCP(5) ,replace1P(6) ,replaceQueue(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded." DEFVAL { allow } ::= { aclL2RuleEntry 11 } aclL2RuleRateLimit OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Rate limit for matched packet." ::= { aclL2RuleEntry 12 } aclL2RuleReplaceDSCP OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Replace DSCP for matched packet." ::= { aclL2RuleEntry 13 } aclL2RuleReplace1P OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Replace DSCP for matched packet." ::= { aclL2RuleEntry 14 } aclL2RuleReplaceQueue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "ACL L2 Rule Replace Queue." ::= { aclL2RuleEntry 15 } aclL2RuleFilterTimeRange OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "ACL L2 Filter Time Range" ::= { aclL2RuleEntry 16 } aclL2RuleVlanIdMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition." DEFVAL { 'FFFF'h } ::= { aclL2RuleEntry 17 } aclL2RuleInPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list." ::= { aclL2RuleEntry 51 } aclL2RuleInVlanList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the complete set of Vlan over which this filter is applied for packets ingress at vlan . Notice : Only support one VLAN." ::= { aclL2RuleEntry 52 } aclL2RuleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aclL2RuleEntry 99 } -- ------------------------------------------------------------------ -- L3 Filter Group -------------------------------------------------- aclL3Rule OBJECT IDENTIFIER ::= { companyACLGroup 3 } aclL3RuleTable OBJECT-TYPE SYNTAX SEQUENCE OF AclL3RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A table to configure L3 filter rules in the system. " ::= { aclL3Rule 1 } aclL3RuleEntry OBJECT-TYPE SYNTAX AclL3RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID." INDEX {aclL3RuleProfileNo, aclL3RuleAccessID } ::= { aclL3RuleTable 1 } AclL3RuleEntry ::= SEQUENCE { aclL3RuleAccessID Integer32, aclL3RuleProfileNo Integer32, aclL3RuleProtocol INTEGER, aclL3RuleProtocolMask OCTET STRING, aclL3RuleICMPMessageType Integer32, aclL3RuleICMPMessageCode Integer32, aclL3RuleDstIpAddr IpAddress, aclL3RuleSrcIpAddr IpAddress, aclL3RuleDstIpAddrMask IpAddress, aclL3RuleSrcIpAddrMask IpAddress, aclL3RuleTcpUdpDstPort Integer32, aclL3RuleTcpUdpSrcPort Integer32, aclL3RuleTcpUdpDstPortMask OCTET STRING, aclL3RuleTcpUdpSrcPortMask OCTET STRING, aclL3RuleTcpAckBit INTEGER, aclL3RuleTcpRstBit INTEGER, aclL3RuleTcpUrgBit INTEGER, aclL3RuleTcpPshBit INTEGER, aclL3RuleTcpSynBit INTEGER, aclL3RuleTcpFinBit INTEGER, aclL3RuleDscp Integer32, aclL3RuleTos Integer32, aclL3RuleIgmpType Integer32, aclL3RuleAction INTEGER, aclL3RuleRateLimit Unsigned32, aclL3RuleReplaceDSCP Integer32, aclL3RuleReplace1P Integer32, aclL3RuleReplaceQueue Integer32, aclL3RuleFilterTimeRange OCTET STRING, aclL3RulePortList PortList, aclL3RuleVlanList OCTET STRING, aclL3RuleStatus RowStatus } aclL3RuleAccessID OBJECT-TYPE SYNTAX Integer32 (0..250) MAX-ACCESS read-only STATUS current DESCRIPTION "L3 Filter rule ID. 0 means auto assign." ::= { aclL3RuleEntry 1 } aclL3RuleProfileNo OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS read-only STATUS current DESCRIPTION "The Profile ID which this rule join." ::= { aclL3RuleEntry 2 } aclL3RuleProtocol OBJECT-TYPE SYNTAX INTEGER { icmp(1), igmp(2), tcp(6), udp(17) } MAX-ACCESS read-write STATUS current DESCRIPTION " The type of protocol to be checked against the packet." ::= { aclL3RuleEntry 3 } aclL3RuleProtocolMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format. " DEFVAL { 'FF'h } ::= { aclL3RuleEntry 4 } aclL3RuleICMPMessageType OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18), " DEFVAL { -1 } ::= { aclL3RuleEntry 5 } aclL3RuleICMPMessageCode OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12), " DEFVAL { -1 } ::= { aclL3RuleEntry 6 } aclL3RuleDstIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition." DEFVAL { '00000000'h } ::= { aclL3RuleEntry 7 } aclL3RuleSrcIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition." DEFVAL { '00000000'h } ::= { aclL3RuleEntry 8 } aclL3RuleDstIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting. " DEFVAL { 'FFFFFFFF'h } ::= { aclL3RuleEntry 9 } aclL3RuleSrcIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting. " DEFVAL { 'FFFFFFFF'h } ::= { aclL3RuleEntry 10 } aclL3RuleTcpUdpDstPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3RuleEntry 11 } aclL3RuleTcpUdpSrcPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP source port. The default value is -1, which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3RuleEntry 12 } aclL3RuleTcpUdpDstPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting. " ::= { aclL3RuleEntry 13 } aclL3RuleTcpUdpSrcPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting. " ::= { aclL3RuleEntry 14 } aclL3RuleTcpAckBit OBJECT-TYPE SYNTAX INTEGER { dont_care(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP ACK bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition." DEFVAL { dont_care } ::= { aclL3RuleEntry 15 } aclL3RuleTcpRstBit OBJECT-TYPE SYNTAX INTEGER { dont_care(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP RST bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition." DEFVAL { dont_care } ::= { aclL3RuleEntry 16 } aclL3RuleTcpUrgBit OBJECT-TYPE SYNTAX INTEGER { dont_care(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Urg bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition." DEFVAL { dont_care } ::= { aclL3RuleEntry 17 } aclL3RuleTcpPshBit OBJECT-TYPE SYNTAX INTEGER { dont_care(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Psh bit to be checked against the packet. The default value is 'dont_care'(-1). which means the rule don't care this condition." DEFVAL { dont_care } ::= { aclL3RuleEntry 18 } aclL3RuleTcpSynBit OBJECT-TYPE SYNTAX INTEGER { dont_care(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Syn bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition." DEFVAL { dont_care } ::= { aclL3RuleEntry 19 } aclL3RuleTcpFinBit OBJECT-TYPE SYNTAX INTEGER { dont_care(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Fin bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition." DEFVAL { dont_care } ::= { aclL3RuleEntry 20 } aclL3RuleDscp OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-create STATUS current DESCRIPTION " The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3RuleEntry 21 } aclL3RuleTos OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-create STATUS current DESCRIPTION " The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3RuleEntry 22 } aclL3RuleIgmpType OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclL3RuleEntry 23 } aclL3RuleAction OBJECT-TYPE SYNTAX INTEGER { allow (1) ,drop (2) ,mirror (3) ,rateLimit(4) ,replaceDSCP(5) ,replace1P(6) ,replaceQueue(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to be taken on the packet if the filter rule matches." DEFVAL { allow } ::= { aclL3RuleEntry 25 } aclL3RuleRateLimit OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Rate limit for matched packet." ::= { aclL3RuleEntry 26 } aclL3RuleReplaceDSCP OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-write STATUS current DESCRIPTION "ReplaceDSCP for matched packet." ::= { aclL3RuleEntry 27 } aclL3RuleReplace1P OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "ReplaceDSCP for matched packet." ::= { aclL3RuleEntry 28 } aclL3RuleReplaceQueue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Acl L3 Rule Replace Queue." ::= { aclL3RuleEntry 29 } aclL3RuleFilterTimeRange OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "ACL L3 Filter Time Range" ::= { aclL3RuleEntry 30 } aclL3RulePortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable." ::= { aclL3RuleEntry 51 } aclL3RuleVlanList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the complete set of vlan over which if the packet arrives this filter rule will be applicable. Notice : only support one vlan." ::= { aclL3RuleEntry 52 } aclL3RuleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aclL3RuleEntry 99 } ---------------------------------------------------------------------------------------- aclv6L3RuleTable OBJECT-TYPE SYNTAX SEQUENCE OF Aclv6L3RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A table to configure L3 filter rules in the system. " ::= { aclL3Rule 2 } aclv6L3RuleEntry OBJECT-TYPE SYNTAX Aclv6L3RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID." INDEX {aclv6L3RuleProfileNo, aclv6L3RuleAccessID } ::= { aclv6L3RuleTable 1 } Aclv6L3RuleEntry ::= SEQUENCE { aclv6L3RuleAccessID Integer32, aclv6L3RuleProfileNo Integer32, aclv6L3RuleProtocol INTEGER, aclv6L3RuleProtocolMask OCTET STRING, aclv6L3RuleICMPMessageType Integer32, aclv6L3RuleICMPMessageCode Integer32, aclv6L3RuleDstIpAddr Ipv6Address, aclv6L3RuleSrcIpAddr Ipv6Address, aclv6L3RuleDstIpAddrMask Ipv6Address, aclv6L3RuleSrcIpAddrMask Ipv6Address, aclv6L3RuleTcpUdpDstPort Integer32, aclv6L3RuleTcpUdpSrcPort Integer32, aclv6L3RuleTcpUdpDstPortMask OCTET STRING, aclv6L3RuleTcpUdpSrcPortMask OCTET STRING, aclv6L3RuleTcpAckBit INTEGER, aclv6L3RuleTcpRstBit INTEGER, aclv6L3RuleTcpUrgBit INTEGER, aclv6L3RuleTcpPshBit INTEGER, aclv6L3RuleTcpSynBit INTEGER, aclv6L3RuleTcpFinBit INTEGER, aclv6L3RuleTrafficClass Integer32, aclv6L3RuleAction INTEGER, aclv6L3RuleRateLimit Unsigned32, aclv6L3RuleReplaceDSCP Integer32, aclv6L3RuleReplace1P Integer32, aclv6L3RuleReplaceQueue Integer32, aclv6L3RuleFilterTimeRange OCTET STRING, aclv6L3RulePortList PortList, aclv6L3RuleVlanList OCTET STRING, aclv6L3RuleStatus RowStatus } aclv6L3RuleAccessID OBJECT-TYPE SYNTAX Integer32 (0..250) MAX-ACCESS read-only STATUS current DESCRIPTION "L3 Filter rule ID. 0 means auto assign." ::= { aclv6L3RuleEntry 1 } aclv6L3RuleProfileNo OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS read-only STATUS current DESCRIPTION "The Profile ID which this rule join." ::= { aclv6L3RuleEntry 2 } aclv6L3RuleProtocol OBJECT-TYPE SYNTAX INTEGER { tcp(6), udp(17), icmpv6(58) } MAX-ACCESS read-write STATUS current DESCRIPTION " The type of protocol to be checked against the packet." ::= { aclv6L3RuleEntry 3 } aclv6L3RuleProtocolMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format. " DEFVAL { 'FF'h } ::= { aclv6L3RuleEntry 4 } aclv6L3RuleICMPMessageType OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18), " DEFVAL { -1 } ::= { aclv6L3RuleEntry 5 } aclv6L3RuleICMPMessageCode OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12), " DEFVAL { -1 } ::= { aclv6L3RuleEntry 6 } aclv6L3RuleDstIpAddr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition." DEFVAL { '00000000'h } ::= { aclv6L3RuleEntry 7 } aclv6L3RuleSrcIpAddr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition." DEFVAL { '00000000'h } ::= { aclv6L3RuleEntry 8 } aclv6L3RuleDstIpAddrMask OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting. " DEFVAL { 'FFFFFFFF'h } ::= { aclv6L3RuleEntry 9 } aclv6L3RuleSrcIpAddrMask OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting. " DEFVAL { 'FFFFFFFF'h } ::= { aclv6L3RuleEntry 10 } aclv6L3RuleTcpUdpDstPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition." DEFVAL { -1 } ::= { aclv6L3RuleEntry 11 } aclv6L3RuleTcpUdpSrcPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP source port. The default value is -1, which means the rule don't care this condition." DEFVAL { -1 } ::= { aclv6L3RuleEntry 12 } aclv6L3RuleTcpUdpDstPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting. " ::= { aclv6L3RuleEntry 13 } aclv6L3RuleTcpUdpSrcPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting. " ::= { aclv6L3RuleEntry 14 } aclv6L3RuleTcpAckBit OBJECT-TYPE SYNTAX INTEGER { dont_care(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP ACK bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition." DEFVAL { dont_care } ::= { aclv6L3RuleEntry 15 } aclv6L3RuleTcpRstBit OBJECT-TYPE SYNTAX INTEGER { dont_care(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP RST bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition." DEFVAL { dont_care } ::= { aclv6L3RuleEntry 16 } aclv6L3RuleTcpUrgBit OBJECT-TYPE SYNTAX INTEGER { dont_care(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Urg bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition." DEFVAL { dont_care } ::= { aclv6L3RuleEntry 17 } aclv6L3RuleTcpPshBit OBJECT-TYPE SYNTAX INTEGER { dont_care(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Psh bit to be checked against the packet. The default value is 'dont_care'(-1). which means the rule don't care this condition." DEFVAL { dont_care } ::= { aclv6L3RuleEntry 18 } aclv6L3RuleTcpSynBit OBJECT-TYPE SYNTAX INTEGER { dont_care(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Syn bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition." DEFVAL { dont_care } ::= { aclv6L3RuleEntry 19 } aclv6L3RuleTcpFinBit OBJECT-TYPE SYNTAX INTEGER { dont_care(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Fin bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition." DEFVAL { dont_care } ::= { aclv6L3RuleEntry 20 } aclv6L3RuleTrafficClass OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-create STATUS current DESCRIPTION " The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { aclv6L3RuleEntry 21 } aclv6L3RuleAction OBJECT-TYPE SYNTAX INTEGER { allow (1) ,drop (2) ,mirror (3) ,rateLimit(4) ,replaceDSCP(5) ,replace1P(6) ,replaceQueue(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to be taken on the packet if the filter rule matches." DEFVAL { allow } ::= { aclv6L3RuleEntry 24 } aclv6L3RuleRateLimit OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Rate limit for matched packet." ::= { aclv6L3RuleEntry 25 } aclv6L3RuleReplaceDSCP OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Replace DSCP for matched packet." ::= { aclv6L3RuleEntry 26 } aclv6L3RuleReplace1P OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Replace DSCP for matched packet." ::= { aclv6L3RuleEntry 27 } aclv6L3RuleReplaceQueue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Acl IPV6 L3 Rule Replace Queue." ::= { aclv6L3RuleEntry 28 } aclv6L3RuleFilterTimeRange OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "ACL IPV6 L3 Filter Time Range" ::= { aclv6L3RuleEntry 29 } aclv6L3RulePortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable." ::= { aclv6L3RuleEntry 51 } aclv6L3RuleVlanList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the complete set of vlan over which if the packet arrives this filter rule will be applicable. Notice : only support one vlan." ::= { aclv6L3RuleEntry 52 } aclv6L3RuleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aclv6L3RuleEntry 99 } -- ------------------------------------------------------------------ -- PacketContent Filter Group -------------------------------------------------- aclPacketRule OBJECT IDENTIFIER ::= { companyACLGroup 4 } aclPacketRuleTable OBJECT-TYPE SYNTAX SEQUENCE OF AclPacketRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to configure Packet Content filter rules in the system." ::= { aclPacketRule 1 } aclPacketRuleEntry OBJECT-TYPE SYNTAX AclPacketRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table is a Packet filter rule. Index to the table is the Packet filter number and Profile ID." INDEX {aclPacketProfileID, aclPacketAccessID} ::= { aclPacketRuleTable 1 } AclPacketRuleEntry ::= SEQUENCE { aclPacketAccessID Integer32, aclPacketProfileID Integer32, aclPacketRuleOffsetValue1 OCTET STRING, aclPacketRuleOffsetValue2 OCTET STRING, aclPacketRuleOffsetValue3 OCTET STRING, aclPacketRuleOffsetValue4 OCTET STRING, aclPacketRuleAction INTEGER, aclPacketRuleRateLimit Unsigned32, aclPacketRuleReplaceDSCP Integer32, aclPacketRuleReplace1P Integer32, aclPacketRuleReplaceQueue Integer32, aclPacketRuleFilterTimeRange OCTET STRING, aclPacketRuleOffsetValue1Mask OCTET STRING, aclPacketRuleOffsetValue2Mask OCTET STRING, aclPacketRuleOffsetValue3Mask OCTET STRING, aclPacketRuleOffsetValue4Mask OCTET STRING, aclPacketRuleInPortList PortList, aclPacketRuleInVlanList OCTET STRING, aclPacketRuleStatus RowStatus } aclPacketAccessID OBJECT-TYPE SYNTAX Integer32 (0..250) MAX-ACCESS read-only STATUS current DESCRIPTION "Packet Filter rule ID. 0 means auto assign." ::= { aclPacketRuleEntry 1 } aclPacketProfileID OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS read-only STATUS current DESCRIPTION "ACL Profile ID which this rule join." ::= { aclPacketRuleEntry 2 } aclPacketRuleOffsetValue1 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The filter value of Offset 1." ::= { aclPacketRuleEntry 3 } aclPacketRuleOffsetValue2 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The filter value of Offset 2." ::= { aclPacketRuleEntry 4 } aclPacketRuleOffsetValue3 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The filter value of Offset 3." ::= { aclPacketRuleEntry 5 } aclPacketRuleOffsetValue4 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The filter value of Offset 4." ::= { aclPacketRuleEntry 6 } aclPacketRuleAction OBJECT-TYPE SYNTAX INTEGER { allow (1) ,drop (2) ,mirror (3) ,rateLimit(4) ,replaceDSCP(5) ,replace1P(6) ,replaceQueue(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded." DEFVAL { allow } ::= { aclPacketRuleEntry 8 } aclPacketRuleRateLimit OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Rate limit for matched packet." ::= { aclPacketRuleEntry 9 } aclPacketRuleReplaceDSCP OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Replace DSCP for matched packet." ::= { aclPacketRuleEntry 10 } aclPacketRuleReplace1P OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Replace 1p for matched packet." ::= { aclPacketRuleEntry 11 } aclPacketRuleReplaceQueue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Acl Rule Replace Queue." ::= { aclPacketRuleEntry 12 } aclPacketRuleFilterTimeRange OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "Acl Filter Time Range" ::= { aclPacketRuleEntry 13 } aclPacketRuleOffsetValue1Mask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The filter Mask of Offset 1." DEFVAL { 'FFFF'h } ::= { aclPacketRuleEntry 14 } aclPacketRuleOffsetValue2Mask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The filter Mask of Offset 2." DEFVAL { 'FFFF'h } ::= { aclPacketRuleEntry 15 } aclPacketRuleOffsetValue3Mask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The filter Mask of Offset 3." DEFVAL { 'FFFF'h } ::= { aclPacketRuleEntry 16 } aclPacketRuleOffsetValue4Mask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The filter Mask of Offset 4." DEFVAL { 'FFFF'h } ::= { aclPacketRuleEntry 17 } aclPacketRuleInPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list." ::= { aclPacketRuleEntry 51 } aclPacketRuleInVlanList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the complete set of vlan over which this filter is applied for packets ingress at vlan. Notice : Only support one vlan." ::= { aclPacketRuleEntry 52 } aclPacketRuleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aclPacketRuleEntry 99 } -- Flow Meter Group -------------------------------------------------- aclFlowMeterRule OBJECT IDENTIFIER ::= { companyACLGroup 10 } aclFlowMeterTable OBJECT-TYPE SYNTAX SEQUENCE OF AclFlowMeterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to configure L2 filter rules in the system." ::= { aclFlowMeterRule 1 } aclFlowMeterEntry OBJECT-TYPE SYNTAX AclFlowMeterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID." INDEX {aclFlowMeterProfileID, aclFlowMeterAccessID} ::= { aclFlowMeterTable 1 } AclFlowMeterEntry ::= SEQUENCE { aclFlowMeterProfileID Integer32, aclFlowMeterAccessID Integer32, aclFlowMeterRate Integer32, aclFlowMeterBurstSize Integer32, aclFlowMeterReplaceDscp Integer32, aclFlowMeterAction INTEGER, aclFlowMeterStatus RowStatus } aclFlowMeterProfileID OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS read-only STATUS current DESCRIPTION "ACL Profile ID which this flow meter join." ::= { aclFlowMeterEntry 1 } aclFlowMeterAccessID OBJECT-TYPE SYNTAX Integer32 (1..250) MAX-ACCESS read-only STATUS current DESCRIPTION "ACL Access ID which this flow meter join." ::= { aclFlowMeterEntry 2 } aclFlowMeterRate OBJECT-TYPE SYNTAX Integer32 (64..1024000) MAX-ACCESS read-write STATUS current DESCRIPTION "The rate limiter of meter." ::= { aclFlowMeterEntry 3 } aclFlowMeterBurstSize OBJECT-TYPE SYNTAX Integer32 (0..1016) MAX-ACCESS read-write STATUS current DESCRIPTION "The burst size of meter." ::= { aclFlowMeterEntry 4 } aclFlowMeterReplaceDscp OBJECT-TYPE SYNTAX Integer32 (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Replace DSCP for matched out-band packets when aclFlowMeterAction is replace DSCP." ::= { aclFlowMeterEntry 5 } aclFlowMeterAction OBJECT-TYPE SYNTAX INTEGER { drop (2) ,replaceDSCP(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to be taken on the out-band packet if the filter rule matches. If the action is 'drop', the packet will be discarded." DEFVAL { drop } ::= { aclFlowMeterEntry 6 } aclFlowMeterStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aclFlowMeterEntry 99 } -- Vlan Based Profile Group -------------------------------------------------- -- aclVlanBasedProfile OBJECT IDENTIFIER ::= { companyACLGroup 20 } -- -- aclVlanBasedProfileTable OBJECT-TYPE -- -- SYNTAX SEQUENCE OF AclVlanBasedProfileEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "A table to configure L2 filter rules in the system." -- ::= { aclVlanBasedProfile 1 } -- -- aclVlanBasedProfileEntry OBJECT-TYPE -- SYNTAX AclVlanBasedProfileEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "Each entry in this table is a L2 filter rule. -- Index to the table is the L2 filter number and Profile ID." -- INDEX {aclVlanBasedProfileNo} -- ::= { aclVlanBasedProfileTable 1 } -- -- AclVlanBasedProfileEntry ::= -- SEQUENCE { -- aclVlanBasedProfileNo -- Integer32, -- aclVlanBasedProfileActiveVlan -- Integer32, -- aclVlanBasedProfileActivePortList -- PortList -- } -- -- aclVlanBasedProfileNo OBJECT-TYPE -- SYNTAX Integer32 (1..50) -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "ACL Profile ID which this flow meter join." -- ::= { aclVlanBasedProfileEntry 1 } -- -- aclVlanBasedProfileActiveVlan OBJECT-TYPE -- SYNTAX Integer32 (0..4094) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "ACL Access ID which this flow meter join." -- ::= { aclVlanBasedProfileEntry 2 } -- -- aclVlanBasedProfileActivePortList OBJECT-TYPE -- SYNTAX PortList -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The rate limiter of meter." -- ::= { aclVlanBasedProfileEntry 3 } -- ------------------------------------------------------------------ -- companyCPUInterfaceFilterGroup -- ------------------------------------------------------------------ -- CPU Interface Filter Profile Group -------------------------------------------------- cpuFilterProfile OBJECT IDENTIFIER ::= { companyCPUInterfaceFilterGroup 1 } ipv4cpuFilterProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF Ipv4CpuFilterProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A table to CPUInterfaceFilter profile . " ::= { cpuFilterProfile 1 } ipv4cpuFilterProfileEntry OBJECT-TYPE SYNTAX Ipv4CpuFilterProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Each entry in this table is a CPUInterfaceFilter profile. Index to the table is CPUInterfaceFilter profile ID. " INDEX { ipv4cpuFilterProfileNo} ::= { ipv4cpuFilterProfileTable 1 } Ipv4CpuFilterProfileEntry ::= SEQUENCE { ipv4cpuFilterProfileNo Integer32, ipv4cpuFilterProfileType INTEGER, ipv4cpuFilterProfileRuleCount Integer32, ipv4cpuFilterProfileMask OCTET STRING, ipv4cpuFilterProfileDstMacAddrMask MacAddress, ipv4cpuFilterProfileSrcMacAddrMask MacAddress, ipv4cpuFilterProfileIPProtocol INTEGER, ipv4cpuFilterProfileIPProtocolMask OCTET STRING, ipv4cpuFilterProfileDstIpAddrMask IpAddress, ipv4cpuFilterProfileSrcIpAddrMask IpAddress, ipv4cpuFilterProfileDstPortMask OCTET STRING, ipv4cpuFilterProfileSrcPortMask OCTET STRING, ipv4cpuFilterProfileStatus RowStatus } ipv4cpuFilterProfileNo OBJECT-TYPE SYNTAX Integer32 (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "The CPUInterfaceFilter Profile ID. The ID 1 to 50 is user-defined CPUInterfaceFilter, and the ID more than 50 is reserved for system-defined CPUInterfaceFilter. The user only allow to create user-defined CPUInterfaceFilter ID. And system-defined CPUInterfaceFilter is read only." ::= { ipv4cpuFilterProfileEntry 1 } ipv4cpuFilterProfileType OBJECT-TYPE SYNTAX INTEGER { l2 (1), l3 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, " ::= { ipv4cpuFilterProfileEntry 2 } ipv4cpuFilterProfileRuleCount OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of rules in this profile." ::= { ipv4cpuFilterProfileEntry 3 } ipv4cpuFilterProfileMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID 2 L2 8021P_PRIORITY 3 L2 ETHER_TYPE 4 L3 DSCP 5 L3 ICMP_TYPE 6 L3 ICMP_CODE 7 L3 IGMP_TYPE 8 L3 DST_IP 9 L3 SRC_IP 10 L3 DST_PORT 11 L3 SRC_PORT 12 L3 TCPFLAG 13 (MSB) ------------------------------------------- The value is in Hex format. " ::= { ipv4cpuFilterProfileEntry 4 } ipv4cpuFilterProfileDstMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile destination MAC address mask. If DST_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleDstMacAddr, to caculate a range of MAC address which is really care. " ::= { ipv4cpuFilterProfileEntry 5 } ipv4cpuFilterProfileSrcMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile source MAC address mask. If SRC_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleSrcMacAddr, to caculate a range of MAC address which is really care. " ::= { ipv4cpuFilterProfileEntry 6 } ipv4cpuFilterProfileIPProtocol OBJECT-TYPE SYNTAX INTEGER { none(0), icmp(1), igmp(2), tcp(6), udp(17) ,ipMask(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. " ::= { ipv4cpuFilterProfileEntry 7 } ipv4cpuFilterProfileIPProtocolMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile IP protocol mask. If cpuFilterProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,cpuFilterL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format. " DEFVAL { 'FF'h } ::= { ipv4cpuFilterProfileEntry 8 } ipv4cpuFilterProfileDstIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile destination IP address mask. If DST_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00' " DEFVAL { 'FFFFFFFF'h } ::= { ipv4cpuFilterProfileEntry 9 } ipv4cpuFilterProfileSrcIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile source IP address mask. If SRC_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00' " DEFVAL { 'FFFFFFFF'h } ::= { ipv4cpuFilterProfileEntry 10 } ipv4cpuFilterProfileDstPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile UDP/TCP destination port mask. If DST_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format. " DEFVAL { 'FFFF'h } ::= { ipv4cpuFilterProfileEntry 11 } ipv4cpuFilterProfileSrcPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile UDP/TCP source port mask. If SRC_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format. " DEFVAL { 'FFFF'h } ::= { ipv4cpuFilterProfileEntry 12 } ipv4cpuFilterProfileStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of cpuFilterProfileType, cpuFilterProfileMask and ProtocolType are not conflicted. " ::= { ipv4cpuFilterProfileEntry 15 } ------------------------------------------------------------------------------------------- cpuFilterProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF CpuFilterProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A table to CPUInterfaceFilter profile . " ::= { cpuFilterProfile 2 } cpuFilterProfileEntry OBJECT-TYPE SYNTAX CpuFilterProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Each entry in this table is a CPUInterfaceFilter profile. Index to the table is CPUInterfaceFilter profile ID. " INDEX { cpuFilterProfileNo} ::= { cpuFilterProfileTable 1 } CpuFilterProfileEntry ::= SEQUENCE { cpuFilterProfileNo Integer32, cpuFilterProfileType INTEGER, cpuFilterProfileRuleCount Integer32, cpuFilterProfileMask OCTET STRING, cpuFilterProfileDstMacAddrMask MacAddress, cpuFilterProfileSrcMacAddrMask MacAddress, cpuFilterProfileIPProtocol INTEGER, cpuFilterProfileIPProtocolMask OCTET STRING, cpuFilterProfileDstIpAddrMaskType INTEGER, cpuFilterProfileDstIpAddrMask Ipv6Address, cpuFilterProfileSrcIpAddrMaskType INTEGER, cpuFilterProfileSrcIpAddrMask Ipv6Address, cpuFilterProfileDstPortMask OCTET STRING, cpuFilterProfileSrcPortMask OCTET STRING, cpuFilterProfileStatus RowStatus } cpuFilterProfileNo OBJECT-TYPE SYNTAX Integer32 (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "The CPUInterfaceFilter Profile ID. The ID 1 to 50 is user-defined CPUInterfaceFilter, and the ID more than 50 is reserved for system-defined CPUInterfaceFilter. The user only allow to create user-defined CPUInterfaceFilter ID. And system-defined CPUInterfaceFilter is read only." ::= { cpuFilterProfileEntry 1 } cpuFilterProfileType OBJECT-TYPE SYNTAX INTEGER { l2 (1), l3 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, " ::= { cpuFilterProfileEntry 2 } cpuFilterProfileRuleCount OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of rules in this profile." ::= { cpuFilterProfileEntry 3 } cpuFilterProfileMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID 2 L2 8021P_PRIORITY 3 L2 ETHER_TYPE 4 L3 DSCP 5 L3 ICMP_TYPE 6 L3 ICMP_CODE 7 L3 IGMP_TYPE 8 L3 DST_IP 9 L3 SRC_IP 10 L3 DST_PORT 11 L3 SRC_PORT 12 L3 TCPFLAG 13 (MSB) L3 TRAFFIC_CLASS 21 ------------------------------------------- The value is in Hex format. " ::= { cpuFilterProfileEntry 4 } cpuFilterProfileDstMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile destination MAC address mask. If DST_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleDstMacAddr, to caculate a range of MAC address which is really care. " ::= { cpuFilterProfileEntry 5 } cpuFilterProfileSrcMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile source MAC address mask. If SRC_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleSrcMacAddr, to caculate a range of MAC address which is really care. " ::= { cpuFilterProfileEntry 6 } cpuFilterProfileIPProtocol OBJECT-TYPE SYNTAX INTEGER { none(0), icmp(1), igmp(2), tcp(6), udp(17) ,ipMask(255) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. " ::= { cpuFilterProfileEntry 7 } cpuFilterProfileIPProtocolMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile IP protocol mask. If cpuFilterProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,cpuFilterL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format. " DEFVAL { 'FF'h } ::= { cpuFilterProfileEntry 8 } cpuFilterProfileDstIpAddrMaskType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "IPv6 Address type." ::= { cpuFilterProfileEntry 9 } cpuFilterProfileDstIpAddrMask OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile destination IP address mask. If DST_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00' " DEFVAL { 'FFFFFFFF'h } ::= { cpuFilterProfileEntry 10 } cpuFilterProfileSrcIpAddrMaskType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "IPv6 Address type." ::= { cpuFilterProfileEntry 11 } cpuFilterProfileSrcIpAddrMask OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile source IP address mask. If SRC_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00' " DEFVAL { 'FFFFFFFF'h } ::= { cpuFilterProfileEntry 12 } cpuFilterProfileDstPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile UDP/TCP destination port mask. If DST_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format. " DEFVAL { 'FFFF'h } ::= { cpuFilterProfileEntry 13 } cpuFilterProfileSrcPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The CPUInterfaceFilter Profile UDP/TCP source port mask. If SRC_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format. " DEFVAL { 'FFFF'h } ::= { cpuFilterProfileEntry 14 } cpuFilterProfileStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of cpuFilterProfileType, cpuFilterProfileMask and ProtocolType are not conflicted. " ::= { cpuFilterProfileEntry 15 } -- ------------------------------------------------------------------ -- L2 Filter Group -------------------------------------------------- cpuFilterL2Rule OBJECT IDENTIFIER ::= { companyCPUInterfaceFilterGroup 2 } cpuFilterL2RuleTable OBJECT-TYPE SYNTAX SEQUENCE OF CpuFilterL2RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to configure L2 filter rules in the system." ::= { cpuFilterL2Rule 1 } cpuFilterL2RuleEntry OBJECT-TYPE SYNTAX CpuFilterL2RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID." INDEX { cpuFilterL2ProfileID, cpuFilterL2AccessID} ::= { cpuFilterL2RuleTable 1 } CpuFilterL2RuleEntry ::= SEQUENCE { cpuFilterL2ProfileID Integer32, cpuFilterL2AccessID Integer32, cpuFilterL2RuleEtherType Integer32, cpuFilterL2RuleDstMacAddr MacAddress, cpuFilterL2RuleSrcMacAddr MacAddress, cpuFilterL2RuleVlanId Integer32, cpuFilterL2Rule1pPriority Integer32, cpuFilterL2RuleDstMacAddrMask MacAddress, cpuFilterL2RuleSrcMacAddrMask MacAddress, cpuFilterL2RuleInPortList PortList, cpuFilterL2RuleAction INTEGER, cpuFilterL2RuleStatus RowStatus } cpuFilterL2ProfileID OBJECT-TYPE SYNTAX Integer32 (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "L2 Filter rule ID." ::= { cpuFilterL2RuleEntry 1 } cpuFilterL2AccessID OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS read-only STATUS current DESCRIPTION "CPUInterfaceFilter Profile ID which this rule join." DEFVAL { 1 } ::= { cpuFilterL2RuleEntry 2 } cpuFilterL2RuleEtherType OBJECT-TYPE SYNTAX Integer32 (-1 | 1501..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { cpuFilterL2RuleEntry 3 } cpuFilterL2RuleDstMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition." ::= { cpuFilterL2RuleEntry 4 } cpuFilterL2RuleSrcMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address" ::= { cpuFilterL2RuleEntry 5 } cpuFilterL2RuleVlanId OBJECT-TYPE SYNTAX Integer32 (-1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { cpuFilterL2RuleEntry 6 } cpuFilterL2Rule1pPriority OBJECT-TYPE SYNTAX Integer32 (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { cpuFilterL2RuleEntry 7 } cpuFilterL2RuleDstMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting." ::= { cpuFilterL2RuleEntry 8 } cpuFilterL2RuleSrcMacAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting." ::= { cpuFilterL2RuleEntry 9 } cpuFilterL2RuleInPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list." ::= { cpuFilterL2RuleEntry 10 } cpuFilterL2RuleAction OBJECT-TYPE SYNTAX INTEGER { allow (1) ,drop (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded." DEFVAL { allow } ::= { cpuFilterL2RuleEntry 11 } cpuFilterL2RuleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { cpuFilterL2RuleEntry 14 } -- ------------------------------------------------------------------ -- L3 Filter Group -------------------------------------------------- cpuFilterL3Rule OBJECT IDENTIFIER ::= { companyCPUInterfaceFilterGroup 3 } cpuFilterL3RuleTable OBJECT-TYPE SYNTAX SEQUENCE OF CpuFilterL3RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A table to configure L3 filter rules in the system. " ::= { cpuFilterL3Rule 1 } cpuFilterL3RuleEntry OBJECT-TYPE SYNTAX CpuFilterL3RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID." INDEX { cpuFilterL3RuleProfileNo, cpuFilterL3RuleAccessID} ::= { cpuFilterL3RuleTable 1 } CpuFilterL3RuleEntry ::= SEQUENCE { cpuFilterL3RuleProfileNo Integer32, cpuFilterL3RuleAccessID Integer32, cpuFilterL3RuleProtocol INTEGER, cpuFilterL3RuleProtocolMask OCTET STRING, cpuFilterL3RuleICMPMessageType Integer32, cpuFilterL3RuleICMPMessageCode Integer32, cpuFilterL3RuleDstIpAddr IpAddress, cpuFilterL3RuleSrcIpAddr IpAddress, cpuFilterL3RuleDstIpAddrMask IpAddress, cpuFilterL3RuleSrcIpAddrMask IpAddress, cpuFilterL3RuleTcpUdpDstPort Integer32, cpuFilterL3RuleTcpUdpSrcPort Integer32, cpuFilterL3RuleTcpUdpDstPortMask OCTET STRING, cpuFilterL3RuleTcpUdpSrcPortMask OCTET STRING, cpuFilterL3RuleTcpAckBit INTEGER, cpuFilterL3RuleTcpRstBit INTEGER, cpuFilterL3RuleTcpUrgBit INTEGER, cpuFilterL3RuleTcpPshBit INTEGER, cpuFilterL3RuleTcpSynBit INTEGER, cpuFilterL3RuleTcpFinBit INTEGER, cpuFilterL3RuleDscp Integer32, cpuFilterL3RuleIgmpType Integer32, cpuFilterL3RulePortList PortList, cpuFilterL3RuleAction INTEGER, cpuFilterL3RuleStatus RowStatus } cpuFilterL3RuleProfileNo OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS read-only STATUS current DESCRIPTION "L3 Filter rule ID." ::= { cpuFilterL3RuleEntry 1 } cpuFilterL3RuleAccessID OBJECT-TYPE SYNTAX Integer32 (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "The Profile ID which this rule join." ::= { cpuFilterL3RuleEntry 2 } cpuFilterL3RuleProtocol OBJECT-TYPE SYNTAX INTEGER { icmp(1), igmp(2), tcp(6), udp(17) } MAX-ACCESS read-write STATUS current DESCRIPTION " The type of protocol to be checked against the packet." ::= { cpuFilterL3RuleEntry 3 } cpuFilterL3RuleProtocolMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,cpuFilterL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format. " DEFVAL { 'FF'h } ::= { cpuFilterL3RuleEntry 4 } cpuFilterL3RuleICMPMessageType OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in cpuFilterL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18), " DEFVAL { -1 } ::= { cpuFilterL3RuleEntry 5 } cpuFilterL3RuleICMPMessageCode OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in cpuFilterL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12), " DEFVAL { -1 } ::= { cpuFilterL3RuleEntry 6 } cpuFilterL3RuleDstIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition." DEFVAL { '00000000'h } ::= { cpuFilterL3RuleEntry 7 } cpuFilterL3RuleSrcIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition." DEFVAL { '00000000'h } ::= { cpuFilterL3RuleEntry 8 } cpuFilterL3RuleDstIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting. " DEFVAL { 'FFFFFFFF'h } ::= { cpuFilterL3RuleEntry 9 } cpuFilterL3RuleSrcIpAddrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting. " DEFVAL { 'FFFFFFFF'h } ::= { cpuFilterL3RuleEntry 10 } cpuFilterL3RuleTcpUdpDstPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition." DEFVAL { -1 } ::= { cpuFilterL3RuleEntry 11 } cpuFilterL3RuleTcpUdpSrcPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP source port. The default value is -1, which means the rule don't care this condition." DEFVAL { -1 } ::= { cpuFilterL3RuleEntry 12 } cpuFilterL3RuleTcpUdpDstPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting. " ::= { cpuFilterL3RuleEntry 13 } cpuFilterL3RuleTcpUdpSrcPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting. " ::= { cpuFilterL3RuleEntry 14 } cpuFilterL3RuleTcpAckBit OBJECT-TYPE SYNTAX INTEGER { dontcare(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP ACK bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition." DEFVAL { dontcare } ::= { cpuFilterL3RuleEntry 15 } cpuFilterL3RuleTcpRstBit OBJECT-TYPE SYNTAX INTEGER { dontcare(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP RST bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition." DEFVAL { dontcare } ::= { cpuFilterL3RuleEntry 16 } cpuFilterL3RuleTcpUrgBit OBJECT-TYPE SYNTAX INTEGER { dontcare(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Urg bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition." DEFVAL { dontcare } ::= { cpuFilterL3RuleEntry 17 } cpuFilterL3RuleTcpPshBit OBJECT-TYPE SYNTAX INTEGER { dontcare(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Psh bit to be checked against the packet. The default value is 'dontcare'(-1). which means the rule don't care this condition." DEFVAL { dontcare } ::= { cpuFilterL3RuleEntry 18 } cpuFilterL3RuleTcpSynBit OBJECT-TYPE SYNTAX INTEGER { dontcare(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Syn bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition." DEFVAL { dontcare } ::= { cpuFilterL3RuleEntry 19 } cpuFilterL3RuleTcpFinBit OBJECT-TYPE SYNTAX INTEGER { dontcare(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Fin bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition." DEFVAL { dontcare } ::= { cpuFilterL3RuleEntry 20 } cpuFilterL3RuleDscp OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-create STATUS current DESCRIPTION " The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { cpuFilterL3RuleEntry 21 } cpuFilterL3RuleIgmpType OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { cpuFilterL3RuleEntry 22 } cpuFilterL3RulePortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable." ::= { cpuFilterL3RuleEntry 23 } cpuFilterL3RuleAction OBJECT-TYPE SYNTAX INTEGER { allow (1) ,drop (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to be taken on the packet if the filter rule matches." DEFVAL { allow } ::= { cpuFilterL3RuleEntry 24 } cpuFilterL3RuleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { cpuFilterL3RuleEntry 27 } -- L3 IPv6 Filter Group -------------------------------------------------- cpuFilterv6L3RuleTable OBJECT-TYPE SYNTAX SEQUENCE OF CpuFilterv6L3RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " A table to configure L3 filter rules in the system. " ::= { cpuFilterL3Rule 2 } cpuFilterv6L3RuleEntry OBJECT-TYPE SYNTAX CpuFilterv6L3RuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID." INDEX { cpuFilterv6L3RuleProfileNo, cpuFilterv6L3RuleAccessID} ::= { cpuFilterv6L3RuleTable 1 } CpuFilterv6L3RuleEntry ::= SEQUENCE { cpuFilterv6L3RuleProfileNo Integer32, cpuFilterv6L3RuleAccessID Integer32, cpuFilterv6L3RuleProtocol INTEGER, cpuFilterv6L3RuleProtocolMask OCTET STRING, cpuFilterv6L3RuleICMPMessageType Integer32, cpuFilterv6L3RuleICMPMessageCode Integer32, cpuFilterv6L3RuleDstIpAddr Ipv6Address, cpuFilterv6L3RuleSrcIpAddr Ipv6Address, cpuFilterv6L3RuleDstIpAddrMask Ipv6Address, cpuFilterv6L3RuleSrcIpAddrMask Ipv6Address, cpuFilterv6L3RuleTcpUdpDstPort Integer32, cpuFilterv6L3RuleTcpUdpSrcPort Integer32, cpuFilterv6L3RuleTcpUdpDstPortMask OCTET STRING, cpuFilterv6L3RuleTcpUdpSrcPortMask OCTET STRING, cpuFilterv6L3RuleTcpAckBit INTEGER, cpuFilterv6L3RuleTcpRstBit INTEGER, cpuFilterv6L3RuleTcpUrgBit INTEGER, cpuFilterv6L3RuleTcpPshBit INTEGER, cpuFilterv6L3RuleTcpSynBit INTEGER, cpuFilterv6L3RuleTcpFinBit INTEGER, cpuFilterv6L3RuleTrafficClass Integer32, cpuFilterv6L3RulePortList PortList, cpuFilterv6L3RuleAction INTEGER, cpuFilterv6L3RuleStatus RowStatus } cpuFilterv6L3RuleProfileNo OBJECT-TYPE SYNTAX Integer32 (1..5) MAX-ACCESS read-only STATUS current DESCRIPTION "L3 Filter rule ID." ::= { cpuFilterv6L3RuleEntry 1 } cpuFilterv6L3RuleAccessID OBJECT-TYPE SYNTAX Integer32 (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "The Profile ID which this rule join." ::= { cpuFilterv6L3RuleEntry 2 } cpuFilterv6L3RuleProtocol OBJECT-TYPE SYNTAX INTEGER { icmp(1), tcp(6), udp(17) } MAX-ACCESS read-write STATUS current DESCRIPTION " The type of protocol to be checked against the packet." ::= { cpuFilterv6L3RuleEntry 3 } cpuFilterv6L3RuleProtocolMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,cpuFilterL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format. " DEFVAL { 'FF'h } ::= { cpuFilterv6L3RuleEntry 4 } cpuFilterv6L3RuleICMPMessageType OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in cpuFilterL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18), " DEFVAL { -1 } ::= { cpuFilterv6L3RuleEntry 5 } cpuFilterv6L3RuleICMPMessageCode OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION " The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in cpuFilterL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12), " DEFVAL { -1 } ::= { cpuFilterv6L3RuleEntry 6 } cpuFilterv6L3RuleDstIpAddr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition." DEFVAL { '00000000'h } ::= { cpuFilterv6L3RuleEntry 7 } cpuFilterv6L3RuleSrcIpAddr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition." DEFVAL { '00000000'h } ::= { cpuFilterv6L3RuleEntry 8 } cpuFilterv6L3RuleDstIpAddrMask OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting. " DEFVAL { 'FFFFFFFF'h } ::= { cpuFilterv6L3RuleEntry 9 } cpuFilterv6L3RuleSrcIpAddrMask OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting. " DEFVAL { 'FFFFFFFF'h } ::= { cpuFilterv6L3RuleEntry 10 } cpuFilterv6L3RuleTcpUdpDstPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition." DEFVAL { -1 } ::= { cpuFilterv6L3RuleEntry 11 } cpuFilterv6L3RuleTcpUdpSrcPort OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP / UDP source port. The default value is -1, which means the rule don't care this condition." DEFVAL { -1 } ::= { cpuFilterv6L3RuleEntry 12 } cpuFilterv6L3RuleTcpUdpDstPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting. " ::= { cpuFilterv6L3RuleEntry 13 } cpuFilterv6L3RuleTcpUdpSrcPortMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting. " ::= { cpuFilterv6L3RuleEntry 14 } cpuFilterv6L3RuleTcpAckBit OBJECT-TYPE SYNTAX INTEGER { dontcare(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP ACK bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition." DEFVAL { dontcare } ::= { cpuFilterv6L3RuleEntry 15 } cpuFilterv6L3RuleTcpRstBit OBJECT-TYPE SYNTAX INTEGER { dontcare(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP RST bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition." DEFVAL { dontcare } ::= { cpuFilterv6L3RuleEntry 16 } cpuFilterv6L3RuleTcpUrgBit OBJECT-TYPE SYNTAX INTEGER { dontcare(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Urg bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition." DEFVAL { dontcare } ::= { cpuFilterv6L3RuleEntry 17 } cpuFilterv6L3RuleTcpPshBit OBJECT-TYPE SYNTAX INTEGER { dontcare(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Psh bit to be checked against the packet. The default value is 'dontcare'(-1). which means the rule don't care this condition." DEFVAL { dontcare } ::= { cpuFilterv6L3RuleEntry 18 } cpuFilterv6L3RuleTcpSynBit OBJECT-TYPE SYNTAX INTEGER { dontcare(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Syn bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition." DEFVAL { dontcare } ::= { cpuFilterv6L3RuleEntry 19 } cpuFilterv6L3RuleTcpFinBit OBJECT-TYPE SYNTAX INTEGER { dontcare(-1), establish(1), notEstablish(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The TCP Fin bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition." DEFVAL { dontcare } ::= { cpuFilterv6L3RuleEntry 20 } cpuFilterv6L3RuleTrafficClass OBJECT-TYPE SYNTAX Integer32 (-1..63) MAX-ACCESS read-create STATUS current DESCRIPTION " The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition." DEFVAL { -1 } ::= { cpuFilterv6L3RuleEntry 21 } cpuFilterv6L3RulePortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable." ::= { cpuFilterv6L3RuleEntry 22 } cpuFilterv6L3RuleAction OBJECT-TYPE SYNTAX INTEGER { allow (1) ,drop (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the action to be taken on the packet if the filter rule matches." DEFVAL { allow } ::= { cpuFilterv6L3RuleEntry 23 } cpuFilterv6L3RuleStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { cpuFilterv6L3RuleEntry 24 } snmpGlobalState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling SNMP Community function." ::= { companySNMPV3 1 } snmpV3User OBJECT IDENTIFIER ::= { companySNMPV3 2 } snmpV3Group OBJECT IDENTIFIER ::= { companySNMPV3 3 } snmpV3ViewTree OBJECT IDENTIFIER ::= { companySNMPV3 4 } snmpV3Community OBJECT IDENTIFIER ::= { companySNMPV3 5 } snmpV3Host OBJECT IDENTIFIER ::= { companySNMPV3 6 } snmpV3EngineID OBJECT-TYPE SYNTAX SnmpEngineID MAX-ACCESS read-write STATUS current DESCRIPTION "An SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the value of the snmpEngineID of a remote SNMP engine with which this user can communicate." ::= { companySNMPV3 7 } snmpV3Trap OBJECT IDENTIFIER ::= { companySNMPV3 8 } -- ---------------------------------------------------------------- -- The snmpV3User group -- ---------------------------------------------------------------- snmpV3UserTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpV3UserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { snmpV3User 1 } snmpV3UserEntry OBJECT-TYPE SYNTAX SnmpV3UserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { snmpV3UserName , snmpV3UserVersion} ::= { snmpV3UserTable 1 } SnmpV3UserEntry ::= SEQUENCE { snmpV3UserName SnmpAdminString, snmpV3UserVersion INTEGER, snmpV3UserGroupName SnmpAdminString, snmpV3UserAuthProtocol INTEGER, snmpV3UserAuthProtocolPassword SnmpAdminString, snmpV3UserPrivProtocol INTEGER, snmpV3UserPrivProtocolPassword SnmpAdminString, snmpV3UserStatus RowStatus } snmpV3UserName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. " ::= { snmpV3UserEntry 1 } snmpV3UserVersion OBJECT-TYPE SYNTAX INTEGER { v1 (1), v2c (2), v3 (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. " ::= { snmpV3UserEntry 2 } snmpV3UserGroupName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable. " ::= { snmpV3UserEntry 3 } snmpV3UserAuthProtocol OBJECT-TYPE SYNTAX INTEGER { none (1), md5 (2), sha (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type of authentication protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of UserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoAuthProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoAuthProtocol, then an 'inconsistentValue' error must be returned. If a set operation tries to set the value to the NoAuthProtocol while the UserPrivProtocol value in the same row is not equal to NoPrivProtocol, then an 'inconsistentValue' error must be returned. That means that an SNMP command generator application must first ensure that the UserPrivProtocol is set to the NoPrivProtocol value before it can set the UserAuthProtocol value to NoAuthProtocol. " ::= { snmpV3UserEntry 4 } snmpV3UserAuthProtocolPassword OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "" ::= { snmpV3UserEntry 5 } snmpV3UserPrivProtocol OBJECT-TYPE SYNTAX INTEGER { none (1), des (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if so, the type of privacy protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of usmUserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoPrivProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoPrivProtocol, then an 'inconsistentValue' error must be returned. Note that if any privacy protocol is used, then you must also use an authentication protocol. In other words, if usmUserPrivProtocol is set to anything else than NoPrivProtocol, then the corresponding instance of usmUserAuthProtocol cannot have a value of usmNoAuthProtocol. If it does, then an 'inconsistentValue' error must be returned. " ::= { snmpV3UserEntry 6 } snmpV3UserPrivProtocolPassword OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "" ::= { snmpV3UserEntry 7 } snmpV3UserStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the usmUserStatus column is 'notReady'. In particular, a newly created row for a user who employs authentication, cannot be made active until the corresponding usmUserCloneFrom and usmUserAuthKeyChange have been set. Further, a newly created row for a user who also employs privacy, cannot be made active until the usmUserPrivKeyChange has been set. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified, except for usmUserOwnAuthKeyChange and usmUserOwnPrivKeyChange. For these 2 objects, the value of usmUserStatus MUST be active. " ::= { snmpV3UserEntry 8 } -- ---------------------------------------------------------------- -- The snmpV3Group group -- ---------------------------------------------------------------- snmpV3GroupTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpV3GroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { snmpV3Group 1 } snmpV3GroupEntry OBJECT-TYPE SYNTAX SnmpV3GroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { snmpV3GroupName ,snmpV3GroupSecurityModel ,snmpV3GroupSecurityLevel} ::= { snmpV3GroupTable 1 } SnmpV3GroupEntry ::= SEQUENCE { snmpV3GroupName SnmpAdminString, snmpV3GroupSecurityModel INTEGER, snmpV3GroupSecurityLevel SnmpSecurityLevel, snmpV3GroupReadViewName SnmpAdminString, snmpV3GroupWriteViewName SnmpAdminString, snmpV3GroupNotifyViewName SnmpAdminString, snmpV3GroupStatus RowStatus } snmpV3GroupName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable. " ::= { snmpV3GroupEntry 1 } snmpV3GroupSecurityModel OBJECT-TYPE SYNTAX INTEGER { v1 (1), v2c (2), v3 (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "In order to gain the access rights allowed by this conceptual row, this securityModel must be in use. " ::= { snmpV3GroupEntry 2 } snmpV3GroupSecurityLevel OBJECT-TYPE SYNTAX SnmpSecurityLevel MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPriv which in turn is less than authPriv. If multiple entries are equally indexed except for this vacmAccessSecurityLevel index, then the entry which has the highest value for vacmAccessSecurityLevel is selected. " ::= { snmpV3GroupEntry 3 } snmpV3GroupReadViewName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted. " -- DEFVAL { ''H } -- -- the empty string -- ::= { snmpV3GroupEntry 4 } snmpV3GroupWriteViewName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted. " -- DEFVAL { ''H } -- -- the empty string -- ::= { snmpV3GroupEntry 5 } snmpV3GroupNotifyViewName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted. " -- DEFVAL { ''H } -- -- the empty string -- ::= { snmpV3GroupEntry 6 } snmpV3GroupStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified. " ::= { snmpV3GroupEntry 7 } -- ---------------------------------------------------------------- -- The snmpV3ViewTree group -- ---------------------------------------------------------------- snmpV3ViewTreeTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpV3ViewTreeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { snmpV3ViewTree 1 } snmpV3ViewTreeEntry OBJECT-TYPE SYNTAX SnmpV3ViewTreeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { snmpV3viewTreeName ,snmpV3viewTreeSubtree } ::= { snmpV3ViewTreeTable 1 } SnmpV3ViewTreeEntry ::= SEQUENCE { snmpV3viewTreeName SnmpAdminString, snmpV3viewTreeSubtree OBJECT IDENTIFIER, snmpV3viewTreeMask OCTET STRING, snmpV3viewTreeType INTEGER, snmpV3viewTreeStatus RowStatus } snmpV3viewTreeName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The human readable name for a family of view subtrees. " ::= { snmpV3ViewTreeEntry 1 } snmpV3viewTreeSubtree OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "The MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees. " ::= { snmpV3ViewTreeEntry 2 } snmpV3viewTreeMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask corresponds to a sub-identifier of vacmViewTreeFamilySubtree, with the most significant bit of the i-th octet of this octet string value (extended if necessary, see below) corresponding to the (8*i - 7)-th sub-identifier, and the least significant bit of the i-th octet of this octet string corresponding to the (8*i)-th sub-identifier, where i is in the range 1 through 16. Each bit of this bit mask specifies whether or not the corresponding sub-identifiers must match when determining if an OBJECT IDENTIFIER is in this family of view subtrees; a '1' indicates that an exact match must occur; a '0' indicates 'wild card', i.e., any sub-identifier value matches. Thus, the OBJECT IDENTIFIER X of an object instance is contained in a family of view subtrees if, for each sub-identifier of the value of vacmViewTreeFamilySubtree, either: the i-th bit of vacmViewTreeFamilyMask is 0, or the i-th sub-identifier of X is equal to the i-th sub-identifier of the value of vacmViewTreeFamilySubtree. If the value of this bit mask is M bits long and there are more than M sub-identifiers in the corresponding instance of vacmViewTreeFamilySubtree, then the bit mask is extended with 1's to be the required length. Note that when the value of this object is the zero-length string, this extension rule results in a mask of all-1's being used (i.e., no 'wild card'), and the family of view subtrees is the one view subtree uniquely identified by the corresponding instance of vacmViewTreeFamilySubtree. Note that masks of length greater than zero length do not need to be supported. In this case this object is made read-only. " -- DEFVAL { ''H } ::= { snmpV3ViewTreeEntry 3 } snmpV3viewTreeType OBJECT-TYPE SYNTAX INTEGER { included(1), excluded(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or excluded from the MIB view. " -- DEFVAL { included } ::= { snmpV3ViewTreeEntry 4 } snmpV3viewTreeStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified. " ::= { snmpV3ViewTreeEntry 5 } -- ---------------------------------------------------------------- -- The snmpV3Community group -- ---------------------------------------------------------------- snmpV3CommunityTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpV3CommunityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { snmpV3Community 1 } snmpV3CommunityEntry OBJECT-TYPE SYNTAX SnmpV3CommunityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { snmpV3CommunityName } ::= { snmpV3CommunityTable 1 } SnmpV3CommunityEntry ::= SEQUENCE { snmpV3CommunityName OCTET STRING, snmpV3CommunityPolicy SnmpAdminString, snmpV3CommunityStatus RowStatus } snmpV3CommunityName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The unique index value of a row in this table." ::= { snmpV3CommunityEntry 1 } snmpV3CommunityPolicy OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "A human readable string representing the corresponding value of snmpCommunityName in a Security Model independent format." ::= { snmpV3CommunityEntry 2 } snmpV3CommunityStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The snmpCommunityName and snmpCommunitySecurityName objects must be explicitly set. There is no restriction on setting columns in this table when the value of snmpCommunityStatus is active(1)." ::= { snmpV3CommunityEntry 3 } -- ---------------------------------------------------------------- -- The snmpV3Host group -- ---------------------------------------------------------------- ipv4snmpV3HostTable OBJECT-TYPE SYNTAX SEQUENCE OF Ipv4snmpV3HostEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "" ::= { snmpV3Host 1 } ipv4snmpV3HostEntry OBJECT-TYPE SYNTAX Ipv4snmpV3HostEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "" INDEX { ipv4snmpV3HostAddress } ::= { ipv4snmpV3HostTable 1 } Ipv4snmpV3HostEntry ::= SEQUENCE { ipv4snmpV3HostAddress IpAddress, ipv4snmpV3HostCommunityName SnmpAdminString, ipv4snmpV3HostVersion INTEGER, ipv4snmpV3HostStatus RowStatus } ipv4snmpV3HostAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS obsolete DESCRIPTION "This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry." ::= { ipv4snmpV3HostEntry 1 } ipv4snmpV3HostCommunityName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS obsolete DESCRIPTION "The locally arbitrary." ::= { ipv4snmpV3HostEntry 2 } ipv4snmpV3HostVersion OBJECT-TYPE SYNTAX INTEGER { v1 (1), v2c (2), v3NoAuthNoPriv (3), v3AuthNoPriv (4), v3AuthPriv (5) } MAX-ACCESS read-create STATUS obsolete DESCRIPTION "The Level of Security to be used when generating SNMP messages using this entry." ::= { ipv4snmpV3HostEntry 3 } ipv4snmpV3HostStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS obsolete DESCRIPTION "" ::= { ipv4snmpV3HostEntry 4 } -- ---------------------------------------------------------------- -- The snmpV3Host group -- ---------------------------------------------------------------- snmpV3HostTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpV3HostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { snmpV3Host 2 } snmpV3HostEntry OBJECT-TYPE SYNTAX SnmpV3HostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { snmpV3HostAddress, snmpV3IPType } ::= { snmpV3HostTable 1 } SnmpV3HostEntry ::= SEQUENCE { snmpV3HostAddress Ipv6Address, snmpV3IPType INTEGER, snmpV3HostCommunityName SnmpAdminString, snmpV3HostVersion INTEGER, snmpV3HostInterfaceName OCTET STRING, snmpV3HostStatus RowStatus } snmpV3HostAddress OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry." ::= { snmpV3HostEntry 1 } snmpV3IPType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of IP interface." ::= { snmpV3HostEntry 2 } snmpV3HostCommunityName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The locally arbitrary." ::= { snmpV3HostEntry 3 } snmpV3HostVersion OBJECT-TYPE SYNTAX INTEGER { v1 (1), v2c (2), v3NoAuthNoPriv (3), v3AuthNoPriv (4), v3AuthPriv (5) } MAX-ACCESS read-create STATUS current DESCRIPTION "The Level of Security to be used when generating SNMP messages using this entry." ::= { snmpV3HostEntry 4 } snmpV3HostInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the interface name when the syslogSrvIP is linklocal address." ::= { snmpV3HostEntry 5 } snmpV3HostStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "" ::= { snmpV3HostEntry 6 } -- ---------------------------------------------------------------- -- The snmpV3Trap group -- ---------------------------------------------------------------- snmpV3TrapSNMPAuthentication OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling SNMP login fail event trap in the system." ::= { snmpV3Trap 1 } snmpV3TrapColdStart OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling devie Bootup event trap in the system." ::= { snmpV3Trap 2 } snmpV3TrapWarmStart OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling devie Bootup event trap in the system." ::= { snmpV3Trap 3 } snmpV3TrapLinkUpDown OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling Copper link up / link down event trap in the system." ::= { snmpV3Trap 4 } snmpV3TrapRSTPStateChange OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling RSTP topology change event trap in the system." ::= { snmpV3Trap 5 } snmpV3TrapFirmUpgrade OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling Firmware upgrade suess or fail event trap in the system." ::= { snmpV3Trap 6 } snmpV3TrapBPDUAttack OBJECT-TYPE SYNTAX INTEGER { none(1), attackDetected(2), attackCleared(3), both(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Used to configure trap settings for BPDU attack protection events." DEFVAL { none } ::= { snmpV3Trap 11 } -- start CAMEO_PORT_SECURITY snmpV3TrapPortSecurity OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "" ::= { snmpV3Trap 12 } -- end CAMEO_PORT_SECURITY -- start CAMEO_IMPBv2 snmpV3TrapIMPBViolation OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "" ::= { snmpV3Trap 13 } -- end CAMEO_IMPBv2 -- start CAMEO_LBD snmpV3TrapLBD OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "" ::= { snmpV3Trap 14 } -- end CAMEO_LBD -- start CAMEO_DHCP_SCREEN snmpV3TrapDHCPServerScreening OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "" ::= { snmpV3Trap 15 } -- end CAMEO_DHCP_SCREEN snmpV3TrapDuplicateIPDetected OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling send gratuitous trap when IP address conflicted in the network." ::= { snmpV3Trap 16 } snmpV3CommunityEncryption OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling community encryption." ::= { companySNMPV3 9 } -- ------------------------------------------------------------------ -- companySyslog -- ------------------------------------------------------------------ syslogSettingGroup OBJECT IDENTIFIER ::= { companySyslog 1 } syslogEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling syslog alert features in the system and the syslog will save to flash or send to remote syslog server. System Logs record and manage events, as well as report errors and informational messages." DEFVAL { disabled } ::= { syslogSettingGroup 1 } syslogSaveMode OBJECT-TYPE SYNTAX INTEGER { onDemand(0), timeInterval(1), logTrigger(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for choosing the method to save syslog into flash." DEFVAL { logTrigger } ::= { syslogSettingGroup 2 } syslogSaveMinutes OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "When savemode is time interval, it's used to set the interval minutes of system save syslog to flash." DEFVAL { 30 } ::= { syslogSettingGroup 3 } -- ------------------------------------------------------------------ -- smtpRecvMailAddrTable -- ------------------------------------------------------------------ ipv4syslogServerGroup OBJECT IDENTIFIER ::= { companySyslog 2 } ipv4syslogServTable OBJECT-TYPE SYNTAX SEQUENCE OF Ipv4SyslogServEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of syslog remote server." ::= { ipv4syslogServerGroup 1 } ipv4syslogServEntry OBJECT-TYPE SYNTAX Ipv4SyslogServEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The list of syslog remote server entry." INDEX { ipv4syslogServIndex } ::= { ipv4syslogServTable 1 } Ipv4SyslogServEntry ::= SEQUENCE { ipv4syslogServIndex INTEGER, ipv4syslogServAddr IpAddress, ipv4syslogServSeverity INTEGER, ipv4syslogServFacility INTEGER, ipv4syslogServUDPport INTEGER, ipv4syslogServSrvStatus INTEGER, ipv4syslogServSrvRowStatus RowStatus } ipv4syslogServIndex OBJECT-TYPE SYNTAX INTEGER (1..4) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of syslog remote server." ::= { ipv4syslogServEntry 1 } ipv4syslogServAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP Address of syslog remote server." ::= { ipv4syslogServEntry 2 } ipv4syslogServSeverity OBJECT-TYPE SYNTAX INTEGER{ warning(4), -- For logging warning messages. information(6), -- For logging informational messages. all(7) -- For logging debug messages. } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the log level option to be set for a specific server." ::= { ipv4syslogServEntry 3 } ipv4syslogServFacility OBJECT-TYPE SYNTAX INTEGER { local0(128), -- Reserved local use local1(136), -- Reserved local use local2(144), -- Reserved local use local3(152), -- Reserved local use local4(160), -- Reserved local use local5(168), -- Reserved local use local6(176), -- Reserved local use local7(184) -- Reserved local use } MAX-ACCESS read-create STATUS current DESCRIPTION "The Syslog standard facilities. The facility to be used when sending Syslog messages to this server." DEFVAL { local0 } ::= { ipv4syslogServEntry 4 } ipv4syslogServUDPport OBJECT-TYPE SYNTAX INTEGER (514 | 6000..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The value is for setting UDP Port." ::= { ipv4syslogServEntry 5 } ipv4syslogServSrvStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The status for this server. If enable, system will send message to this server." ::= { ipv4syslogServEntry 6 } ipv4syslogServSrvRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Row status of this server entry." ::= { ipv4syslogServEntry 7 } -- ------------------------------------------------------------------ -- syslogServTable -- ------------------------------------------------------------------ syslogServerGroup OBJECT IDENTIFIER ::= { companySyslog 3 } syslogServTable OBJECT-TYPE SYNTAX SEQUENCE OF SyslogServEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of syslog remote server." ::= { syslogServerGroup 1 } syslogServEntry OBJECT-TYPE SYNTAX SyslogServEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The list of syslog remote server entry." INDEX { syslogServIndex } ::= { syslogServTable 1 } SyslogServEntry ::= SEQUENCE { syslogServIndex INTEGER, syslogServAddrType INTEGER, syslogServAddr Ipv6Address, syslogServInterfaceName OCTET STRING, syslogServSeverity INTEGER, syslogServFacility INTEGER, syslogServUDPport INTEGER, syslogServSrvStatus INTEGER, syslogServSrvRowStatus RowStatus } syslogServIndex OBJECT-TYPE SYNTAX INTEGER (1..4) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of syslog remote server." ::= { syslogServEntry 1 } syslogServAddrType OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the Address type of server.Address type shall be ipv4 or ipv6." ::= { syslogServEntry 2 } syslogServAddr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the ServerIP to which the syslog shall be forwarded." ::= { syslogServEntry 3 } syslogServInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the interface name when the syslogServInterfaceName is linklocal address." ::= { syslogServEntry 4 } syslogServSeverity OBJECT-TYPE SYNTAX INTEGER{ warning(4), -- For logging warning messages. information(6), -- For logging informational messages. all(7) -- For logging debug messages. } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the log level option to be set for a specific server." ::= { syslogServEntry 5 } syslogServFacility OBJECT-TYPE SYNTAX INTEGER { local0(128), -- Reserved local use local1(136), -- Reserved local use local2(144), -- Reserved local use local3(152), -- Reserved local use local4(160), -- Reserved local use local5(168), -- Reserved local use local6(176), -- Reserved local use local7(184) -- Reserved local use } MAX-ACCESS read-create STATUS current DESCRIPTION "The Syslog standard facilities. The facility to be used when sending Syslog messages to this server." DEFVAL { local0 } ::= { syslogServEntry 6 } syslogServUDPport OBJECT-TYPE SYNTAX INTEGER (514 | 6000..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The value is for setting UDP Port." ::= { syslogServEntry 7 } syslogServSrvStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The status for this server. If enable, system will send message to this server." ::= { syslogServEntry 8 } syslogServSrvRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Row status of this server entry." ::= { syslogServEntry 9 } -- LBD Group ------------------------------------------------------ sysLBDStateEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Loopback detection function. The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree Protocol (STP) is not enabled in the network, especially when the down links are hubs or unmanaged switchs.The Switch will automatically shutdown the port and sends a log to the administrator." DEFVAL { disabled } ::= { companyLBD 1 } sysLBDMode OBJECT-TYPE SYNTAX INTEGER { port(1), vlan(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Loopback detection function mode." DEFVAL { port } ::= { companyLBD 2 } sysLBDInterval OBJECT-TYPE SYNTAX Integer32 (1..32767) MAX-ACCESS read-write STATUS current DESCRIPTION "Set a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds. This time interval to be used at counting time seconds to resend the CTP packet automatically." DEFVAL { 2 } ::= { companyLBD 3 } sysLBDRecoverTime OBJECT-TYPE SYNTAX Integer32 (0 | 60..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "This time interval to be used at counting time seconds to recover the disabled port automatically. The Loop Detection Recover Time can be set at 0 seconds, or 60 to 1000000 seconds. Entering 0 will disable the Loop Detection Recover Time. The default is 60 seconds." DEFVAL { 60 } ::= { companyLBD 4 } -- LBD Port Control Table sysLBDCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF SysLBDCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control Loopback detection features either for the entire switch or for each interface in the switch." ::= { companyLBD 5 } sysLBDCtrlEntry OBJECT-TYPE SYNTAX SysLBDCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system." INDEX { sysLBDCtrlIndex } ::= { sysLBDCtrlTable 1 } SysLBDCtrlEntry ::= SEQUENCE { sysLBDCtrlIndex Integer32, sysLBDPortStatus INTEGER, sysLBDPortLoopStatus INTEGER } sysLBDCtrlIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index of the port for which the configuration in this entry applies." ::= { sysLBDCtrlEntry 1 } sysLBDPortStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Provides control to per port enable or disable the loopback detection function. Default is disabled." DEFVAL { disabled } ::= { sysLBDCtrlEntry 2 } sysLBDPortLoopStatus OBJECT-TYPE SYNTAX INTEGER { normal(1), loop(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The loop status for this port." ::= { sysLBDCtrlEntry 3 } -- LBD Vlan Loop Table sysLBDVlanLoopTable OBJECT-TYPE SYNTAX SEQUENCE OF SysLBDVlanLoopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to display Loopback detection features by vlan mode ." ::= { companyLBD 6 } sysLBDVlanLoopEntry OBJECT-TYPE SYNTAX SysLBDVlanLoopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system." INDEX { sysLBDVlanLoopIndex } ::= { sysLBDVlanLoopTable 1 } SysLBDVlanLoopEntry ::= SEQUENCE { sysLBDVlanLoopIndex Integer32, sysLBDVlanLoopPorts PortList } sysLBDVlanLoopIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Display port lists loop status by vlan." ::= { sysLBDVlanLoopEntry 1 } sysLBDVlanLoopPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "Display port lists loop status by vlan." ::= { sysLBDVlanLoopEntry 2 } -- ------------------------------------------------------------------ -- Mirror Group -- ------------------------------------------------------------------ sysMirrorStatus OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Port Mirroring function. Default is disabled. Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another port where the packet can be studied." -- "Provides control over the mirroring feature in the switch." -- DEFVAL { disabled } ::= { companyMirror 1 } sysMirrorTargetPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the port to which the mirrored traffic in the system is to be copied." ::= { companyMirror 2 } sysMirrorCtrlIngressMirroring OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port." ::= { companyMirror 3 } sysMirrorCtrlEgressMirroring OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port." ::= { companyMirror 4 } -- ------------------------------------------------------------------ -- SNTP Timesetting -- ------------------------------------------------------------------ ipv4sysSNTPTimeSeconds OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS obsolete DESCRIPTION "This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UTC, January 1, 2009) and smaller than 2145916799 (23:59:59 UTC, December 31, 2037)." ::= { companySNTPSetting 1 } ipv4sysSNTPFirstServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "SNTP First Server's IP Address" ::= { companySNTPSetting 2 } ipv4sysSNTPSecondServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "SNTP Second Server's IP Address" ::= { companySNTPSetting 3 } ipv4sysSNTPPollInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS obsolete DESCRIPTION "SNTP Poll Interval In Seconds (30-99999) " ::= { companySNTPSetting 4 } ipv4sysSNTPState OBJECT-TYPE SYNTAX INTEGER { sntp(1), local(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Enable/Disable SNTP function in the system." ::= { companySNTPSetting 5 } -- SNTP TimeZonesetting ipv4sysSNTPDSTOffset OBJECT-TYPE SYNTAX INTEGER { offset30min (30), offset60min (60), offset90min (90), offset120min (120) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes." ::= { companySNTPSetting 6 } ipv4sysSNTPGMTMinutes OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)" ::= { companySNTPSetting 7 } ipv4sysSNTPDSTStartMon OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The start month of Daylight Saving Time." ::= { companySNTPSetting 8 } ipv4sysSNTPDSTStartDay OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The start day of Daylight Saving Time." ::= { companySNTPSetting 9 } ipv4sysSNTPDSTStartHour OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The start hour of Daylight Saving Time." ::= { companySNTPSetting 10 } ipv4sysSNTPDSTStartMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The start minute of Daylight Saving Time." ::= { companySNTPSetting 11 } ipv4sysSNTPDSTEndMon OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The end month of Daylight Saving Time." ::= { companySNTPSetting 12 } ipv4sysSNTPDSTEndDay OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The end day of Daylight Saving Time." ::= { companySNTPSetting 13 } ipv4sysSNTPDSTEndHour OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The end hour of Daylight Saving Time." ::= { companySNTPSetting 14 } ipv4sysSNTPDSTEndMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The end minute of Daylight Saving Time." ::= { companySNTPSetting 15 } ipv4sysSNTPDSTState OBJECT-TYPE SYNTAX INTEGER { annual(1), disabled(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "This object is for Annual(1) or Disabled(2) DST state in the system." ::= { companySNTPSetting 16 } --IPv6 sntp server Table sysSNTPServerTable OBJECT IDENTIFIER ::= { companySNTPSetting 17 } sysSNTPTimeSeconds OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UTC, January 1, 2009) and smaller than 2145916799 (23:59:59 UTC, December 31, 2037)." ::= { sysSNTPServerTable 1 } sysSNTPFirstServer OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP First Server's IPv6 Address" ::= { sysSNTPServerTable 2 } sysSNTPFirstType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP First Server's IPv6 Address type." ::= { sysSNTPServerTable 3 } sysSNTPFirstInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the interface name when the sysSNTPFirstServer is linklocal address." ::= { sysSNTPServerTable 4 } sysSNTPSecondServer OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP Second Server's IPv6 Address" ::= { sysSNTPServerTable 5 } sysSNTPSecondType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP First Server's IPv6 Address type." ::= { sysSNTPServerTable 6 } sysSNTPSecondInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the interface name when the sysSNTPSecondServer is linklocal address." ::= { sysSNTPServerTable 7 } sysSNTPPollInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP Poll Interval In Seconds (30-99999) " ::= { sysSNTPServerTable 8 } sysSNTPState OBJECT-TYPE SYNTAX INTEGER { sntp(1), local(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable SNTP function in the system." ::= { sysSNTPServerTable 9 } -- SNTPv6 TimeZonesetting sysSNTPDSTOffset OBJECT-TYPE SYNTAX INTEGER { offset30min (30), offset60min (60), offset90min (90), offset120min (120) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes." ::= { sysSNTPServerTable 10 } sysSNTPGMTMinutes OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)" ::= { sysSNTPServerTable 11 } sysSNTPDSTStartMon OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The start month of Daylight Saving Time." ::= { sysSNTPServerTable 12 } sysSNTPDSTStartDay OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The start day of Daylight Saving Time." ::= { sysSNTPServerTable 13 } sysSNTPDSTStartHour OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The start hour of Daylight Saving Time." ::= { sysSNTPServerTable 14 } sysSNTPDSTStartMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The start minute of Daylight Saving Time." ::= { sysSNTPServerTable 15 } sysSNTPDSTEndMon OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The end month of Daylight Saving Time." ::= { sysSNTPServerTable 16 } sysSNTPDSTEndDay OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The end day of Daylight Saving Time." ::= { sysSNTPServerTable 17 } sysSNTPDSTEndHour OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The end hour of Daylight Saving Time." ::= { sysSNTPServerTable 18 } sysSNTPDSTEndMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The end minute of Daylight Saving Time." ::= { sysSNTPServerTable 19 } sysSNTPDSTState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for Enabled(1) or Disabled(2) DST state in the system." ::= { sysSNTPServerTable 20 } sysSNTPDSTMethod OBJECT-TYPE SYNTAX INTEGER { annual(1), repeating(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for Annual(1) or Repeating(2) DST method in the system." ::= { sysSNTPServerTable 30 } sysSNTPDSTRepeatStartMon OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The start month of Daylight Saving Time in Repeating mode." ::= { sysSNTPServerTable 31 } sysSNTPDSTRepeatStartWeek OBJECT-TYPE SYNTAX INTEGER { last(0), first(1), second(2), third(3), fourth(4), fifth(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "The start week of Daylight Saving Time in Repeating mode." ::= { sysSNTPServerTable 32 } sysSNTPDSTRepeatStartWeekDay OBJECT-TYPE SYNTAX INTEGER { sun(0), mon(1), tue(2), wed(3), thu(4), fri(5), sat(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "The start weekday of Daylight Saving Time in Repeating mode." ::= { sysSNTPServerTable 33 } sysSNTPDSTRepeatStartHour OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The start hour of Daylight Saving Time in Repeating mode.." ::= { sysSNTPServerTable 34 } sysSNTPDSTRepeatStartMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The start minute of Daylight Saving Time in Repeating mode." ::= { sysSNTPServerTable 35 } sysSNTPDSTRepeatEndMon OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The end month of Daylight Saving Time in Repeating mode." ::= { sysSNTPServerTable 36 } sysSNTPDSTRepeatEndWeek OBJECT-TYPE SYNTAX INTEGER { last(0), first(1), second(2), third(3), fourth(4), fifth(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "The end week of Daylight Saving Time in Repeating mode." ::= { sysSNTPServerTable 37 } sysSNTPDSTRepeatEndWeekDay OBJECT-TYPE SYNTAX INTEGER { sun(0), mon(1), tue(2), wed(3), thu(4), fri(5), sat(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "The end weekday of Daylight Saving Time in Repeating mode." ::= { sysSNTPServerTable 38 } sysSNTPDSTRepeatEndHour OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The end hour of Daylight Saving Time in Repeating mode.." ::= { sysSNTPServerTable 39 } sysSNTPDSTRepeatEndMin OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The end minute of Daylight Saving Time in Repeating mode." ::= { sysSNTPServerTable 40 } -- ------------------------------------------------------------------ -- Limit IP multicast Group -- ------------------------------------------------------------------ limitIpMulticastProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF LimitIpMulticastProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the limit ip multicast Profile Table." ::= { companyLimitIp 1 } limitIpMulticastProfileEntry OBJECT-TYPE SYNTAX LimitIpMulticastProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A limit ip multicast entry maintain by the start IP Address, end ip address, profile id." INDEX { limitIpMulticastIPType, limitIpMulticastProfileID } ::= { limitIpMulticastProfileTable 1 } LimitIpMulticastProfileEntry ::= SEQUENCE { limitIpMulticastIPType INTEGER, limitIpMulticastProfileID INTEGER, limitIpMulticastProfileName DisplayString, limitIpMulticastProfileStatus RowStatus } limitIpMulticastIPType OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate the IP type of profile." ::= { limitIpMulticastProfileEntry 1 } limitIpMulticastProfileID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The ProfileID of the limit ip multicast profile entry." ::= { limitIpMulticastProfileEntry 2 } limitIpMulticastProfileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The ProfileName of the limit ip multicast profile entry." ::= { limitIpMulticastProfileEntry 3 } limitIpMulticastProfileStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of an entry in the limit ip multicast profile Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available." ::= { limitIpMulticastProfileEntry 4 } limitIpMulticastEntryTable OBJECT-TYPE SYNTAX SEQUENCE OF LimitIpMulticastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the limit ip multicast entry Table." ::= { companyLimitIp 2 } limitIpMulticastEntry OBJECT-TYPE SYNTAX LimitIpMulticastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A limit ip multicast entry maintain by the start IP Address, end ip address, profile id." INDEX { limitIpMulticastEntryIPType, limitIpMulticastEntryProfileID, limitIpMulticaststartIpAddr, limitIpMulticastendIpAddr} ::= { limitIpMulticastEntryTable 1 } LimitIpMulticastEntry ::= SEQUENCE { limitIpMulticastEntryIPType INTEGER, limitIpMulticastEntryProfileID INTEGER, limitIpMulticaststartIpAddr DisplayString, limitIpMulticastendIpAddr DisplayString, limitIpMulticastStatus RowStatus } limitIpMulticastEntryIPType OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate the IP type of entry." ::= { limitIpMulticastEntry 1 } limitIpMulticastEntryProfileID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The ProfileID of the limit ip multicast entry." ::= { limitIpMulticastEntry 2 } limitIpMulticaststartIpAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(1..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The limit ip multicast IP address is used to set start ip" ::= { limitIpMulticastEntry 3 } limitIpMulticastendIpAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(1..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The limit ip multicast IP address is used to set end ip" ::= { limitIpMulticastEntry 4 } limitIpMulticastStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of an entry in the limit ip multicast entry Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available." ::= { limitIpMulticastEntry 5 } limitIpMulticastPortTable OBJECT-TYPE SYNTAX SEQUENCE OF LimitIpMulticastPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the limit ip multicast Port entry Table." ::= { companyLimitIp 3 } limitIpMulticastPortEntry OBJECT-TYPE SYNTAX LimitIpMulticastPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A limit ip multicast entry maintain by the Port Index." INDEX { limitIpMulticastPortIPType, limitIpMulticastPortID } ::= { limitIpMulticastPortTable 1 } LimitIpMulticastPortEntry ::= SEQUENCE { limitIpMulticastPortIPType INTEGER, limitIpMulticastPortID INTEGER, limitIpMulticastPortState INTEGER, limitIpMulticastPortProfileID PortList, limitIpMulticastPortMaxGrp INTEGER } limitIpMulticastPortIPType OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate the IP type of entry." ::= { limitIpMulticastPortEntry 1 } limitIpMulticastPortID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The Port Index of the limit ip multicast port entry." ::= { limitIpMulticastPortEntry 2 } limitIpMulticastPortState OBJECT-TYPE SYNTAX INTEGER { permit (1), deny (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The limit ip multicast port state" ::= { limitIpMulticastPortEntry 3 } limitIpMulticastPortProfileID OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The limit ip multicast port mapping profileID list." ::= { limitIpMulticastPortEntry 4 } limitIpMulticastPortMaxGrp OBJECT-TYPE SYNTAX INTEGER (1..256) MAX-ACCESS read-write STATUS current DESCRIPTION "The limit ip multicast per-port max group." ::= { limitIpMulticastPortEntry 5 } -- ----------------------------------------------------------------------------- -- The Guest Vlan Group -- ----------------------------------------------------------------------------- guestVlanName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN name of guest VLAN." ::= { companyGuestVlan 1 } guestVlanPort OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the guest VLAN port members of this device." ::= { companyGuestVlan 2 } guestVlanDelState OBJECT-TYPE SYNTAX INTEGER{ none(1), start(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Used to delete the guest VLAN." ::= { companyGuestVlan 3 } -- ----------------------------------------------------------------------------- -- The Protocol Group Name Table -- ----------------------------------------------------------------------------- protocolGroupNameTable OBJECT-TYPE SYNTAX SEQUENCE OF ProtocolGroupNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control protocol group name features of the device." ::= { companyProtocolVlan 1 } protocolGroupNameEntry OBJECT-TYPE SYNTAX ProtocolGroupNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in protocol group name table for each interface in the system." INDEX {protocolGroupGID} ::= { protocolGroupNameTable 1 } ProtocolGroupNameEntry ::= SEQUENCE { protocolGroupGID Integer32, protocolGroupName DisplayString } protocolGroupGID OBJECT-TYPE SYNTAX Integer32 (1..16) MAX-ACCESS read-only STATUS current DESCRIPTION "The group ID of protocol group name table." ::= { protocolGroupNameEntry 1 } protocolGroupName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The group name of protocol group name table." ::= { protocolGroupNameEntry 2 } -- ----------------------------------------------------------------------------- -- The Protocol Group Table -- ----------------------------------------------------------------------------- protocolGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF ProtocolGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control protocol group features of the device." ::= { companyProtocolVlan 2 } protocolGroupEntry OBJECT-TYPE SYNTAX ProtocolGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in protocol group table for each interface in the system." INDEX {protocolGroupId, protocolGroupFrameType, protocolGroupProtocolValue} ::= { protocolGroupTable 1 } ProtocolGroupEntry ::= SEQUENCE { protocolGroupId Integer32, protocolGroupFrameType INTEGER, protocolGroupProtocolValue Integer32, protocolGroupRowStatus RowStatus } protocolGroupId OBJECT-TYPE SYNTAX Integer32 (1..16) MAX-ACCESS read-only STATUS current DESCRIPTION "The group ID of protocol group table." ::= { protocolGroupEntry 1 } protocolGroupFrameType OBJECT-TYPE SYNTAX INTEGER { ethernet (1), ieee8023_snap (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The frame type of protocol group table." ::= { protocolGroupEntry 2 } protocolGroupProtocolValue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol value of protocol group table." ::= { protocolGroupEntry 3 } protocolGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of protocol group table." ::= { protocolGroupEntry 99 } -- ----------------------------------------------------------------------------- -- The Protocol Vlan Table -- ----------------------------------------------------------------------------- protocolVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF ProtocolVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control protocol vlan features of the device." ::= { companyProtocolVlan 3 } protocolVlanEntry OBJECT-TYPE SYNTAX ProtocolVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in protocol vlan table for each interface in the system." INDEX {protocolVlanPort, protocolVlanVID, protocolVlanGroupID} ::= { protocolVlanTable 1 } ProtocolVlanEntry ::= SEQUENCE { protocolVlanPort Integer32, protocolVlanVID Integer32, protocolVlanGroupID Integer32, protocolVlanRowStatus RowStatus } protocolVlanPort OBJECT-TYPE SYNTAX Integer32 (1..28) MAX-ACCESS read-only STATUS current DESCRIPTION "The interface number of protocol vlan table." ::= { protocolVlanEntry 1 } protocolVlanVID OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan ID of protocol vlan table." ::= { protocolVlanEntry 2 } protocolVlanGroupID OBJECT-TYPE SYNTAX Integer32 (1..16) MAX-ACCESS read-only STATUS current DESCRIPTION "The group ID of protocol vlan table." ::= { protocolVlanEntry 3 } protocolVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of protocol vlan table." ::= { protocolVlanEntry 99 } -- --------------------------------------------------------------------- -- MacNotify Function -- --------------------------------------------------------------------- macNotifyState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object can enabled or disabled MAC Notification." ::= { companyMacNotify 1 } macNotifyInterval OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the time interval in second for trigger the MAC notify message. " --DEFVAL { 1 } ::= { companyMacNotify 2 } macNotifyHistorySize OBJECT-TYPE SYNTAX INTEGER (1..500) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the history size of variation MAC in address table. The default value is 1 ." --DEFVAL { 1 } ::= { companyMacNotify 3 } -- Mac Notify Port Control Table macNotifyCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF MacNotifyCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control Loopback detection features either for the entire switch or for each interface in the switch." ::= { companyMacNotify 4 } macNotifyCtrlEntry OBJECT-TYPE SYNTAX MacNotifyCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system." INDEX { macNotifyCtrlIndex } ::= { macNotifyCtrlTable 1 } MacNotifyCtrlEntry ::= SEQUENCE { macNotifyCtrlIndex Integer32, macNotifyPortStatus INTEGER } macNotifyCtrlIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index of the port for which the configuration in this entry applies." ::= { macNotifyCtrlEntry 1 } macNotifyPortStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Provides control to per port enable or disable the loopback detection function. Default is disabled." DEFVAL { disabled } ::= { macNotifyCtrlEntry 2 } macNotifyInfo OBJECT IDENTIFIER ::= { companyMacNotify 5 } macNotifyInfoDiscription OBJECT-TYPE SYNTAX OCTET STRING(SIZE (1..1024)) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the information for the device MAC address changes. And the detailed information include: Operation Code + MAC address + Box ID + Port Number + Zero... Operation Code: 1, 2 and 3 1 means learned a new MAC address 2 means deleted an old MAC address. 3 means station movement. Box ID: The switch box ID, for standalone device, it always 1. Port Number: The port number learned or deleted for the box. Zero: Used to separate each message (Operate Code + MAC address + Box ID + Port Number)." ::= { macNotifyInfo 1 } -- ------------------------------------------------------------------ -- BPDU Attack Protection Group -- ------------------------------------------------------------------ sysBPDUAttackStateEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Use this to enable BPDU attack protection. The BPDU Attack Protection function and Spanning Tree Protocol for ports are mutually exclusive. When the STP function is enabled on a particular port, BPDU Attack Protection cannot be enabled." DEFVAL { disabled } ::= { companyBPDUAttack 1 } sysBPDUAttackRecoverTime OBJECT-TYPE SYNTAX Integer32 (0 | 60..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "When a port enters under attack state, it can be disabled or blocked based on the configuration. The state can be recovered manually or by the auto recovery mechanism. This command is used to configure the auto-recovery timer. To manually recover the port, the user needs to disable and re-enable the port." DEFVAL { 60 } ::= { companyBPDUAttack 2 } -- BPDUAttack Port Control Table sysBPDUAttackCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF SysBPDUAttackCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control BPDU Attack features either for the entire switch or for each interface in the switch." ::= { companyBPDUAttack 3 } sysBPDUAttackCtrlEntry OBJECT-TYPE SYNTAX SysBPDUAttackCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system." INDEX { sysBPDUAttackCtrlIndex } ::= { sysBPDUAttackCtrlTable 1 } SysBPDUAttackCtrlEntry ::= SEQUENCE { sysBPDUAttackCtrlIndex Integer32, sysBPDUAttackPortState INTEGER, sysBPDUAttackPortMode INTEGER , sysBPDUAttackPortStatus INTEGER } sysBPDUAttackCtrlIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index of the port for which the configuration in this entry applies." ::= { sysBPDUAttackCtrlEntry 1 } sysBPDUAttackPortState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Used to configure the BPDU Attack Protection state of a port. The default state is disable." DEFVAL { disabled } ::= { sysBPDUAttackCtrlEntry 2 } sysBPDUAttackPortMode OBJECT-TYPE SYNTAX INTEGER { drop(1), block(2), shutdown(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Used to configure the BPDU Attack Protection mode of a port." ::= { sysBPDUAttackCtrlEntry 3 } sysBPDUAttackPortStatus OBJECT-TYPE SYNTAX INTEGER { normal(1), underAttack(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Use this to view per port BPDU attack protection status." DEFVAL { normal } ::= { sysBPDUAttackCtrlEntry 4 } sysBPDUAttackLog OBJECT-TYPE SYNTAX INTEGER { none(1), attackDetected(2), attackCleared(3), both(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Used to configure log settings for BPDU attack protection events." DEFVAL { none } ::= { companyBPDUAttack 4 } -- --------------------------------------------------------------------- -- VLAN Trunk Function -- --------------------------------------------------------------------- vlanTrunkSystem OBJECT IDENTIFIER ::= { companyVLANTrunk 1 } -- ------------------------------------------------------------------ -- The La System Group -- ------------------------------------------------------------------ vlanTrunkGlobalStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This indicates the global state of the VLAN trunking feature of the device." ::= { vlanTrunkSystem 1 } vlanTrunkTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanTrunkConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to manage the VLAN trunking feature of the device." ::= { vlanTrunkSystem 2 } vlanTrunkEntry OBJECT-TYPE SYNTAX VlanTrunkConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each created port-channel port." INDEX { vlanTrunkIfIndex } ::= { vlanTrunkTable 1 } VlanTrunkConfigEntry ::= SEQUENCE { vlanTrunkIfIndex InterfaceIndex, vlanTrunkState INTEGER } vlanTrunkIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port. " ::= { vlanTrunkEntry 1 } vlanTrunkState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the VLAN trunk status as enabled or disabled." ::= { vlanTrunkEntry 2 } -- --------------------------------------------------------------------- -- QinQ Function -- --------------------------------------------------------------------- qinqSystem OBJECT IDENTIFIER ::= { companyQinQ 1 } qinqVLANTranslation OBJECT IDENTIFIER ::= { companyQinQ 2 } -- ------------------------------------------------------------------ -- The QinQ System Group -- ------------------------------------------------------------------ qinqGlobalStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to enable/disable the Q-in-Q status." ::= { qinqSystem 1 } qinqInnerTPID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set the Q-in-Q inner TPID." ::= { qinqSystem 2 } qinqTable OBJECT-TYPE SYNTAX SEQUENCE OF QinQConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains Q-in-Q information about each port." ::= { qinqSystem 3 } qinqEntry OBJECT-TYPE SYNTAX QinQConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Q-in-Q information for each port." INDEX { qinqIfIndex } ::= { qinqTable 1 } QinQConfigEntry ::= SEQUENCE { qinqIfIndex InterfaceIndex, qinqRoleState INTEGER, qinqMissDropState INTEGER, qinqOuterTPID Unsigned32, qinqAddInnerTagState INTEGER, qinqAddInnerTagValue Unsigned32 } qinqIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port. " ::= { qinqEntry 1 } qinqRoleState OBJECT-TYPE SYNTAX INTEGER { nni(1), uni(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the QinQ Role as NNI or UNI." ::= { qinqEntry 2 } qinqMissDropState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the QinQ Miss Drop state as enabled or disabled." ::= { qinqEntry 3 } qinqOuterTPID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the QinQ Outer TPID value." ::= { qinqEntry 4 } qinqAddInnerTagState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the QinQ Add Inner Tag state as enabled or disabled." ::= { qinqEntry 5 } qinqAddInnerTagValue OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the QinQ Add Inner Tag value." ::= { qinqEntry 6 } -- -- Vlan Translation Table -- qinqVlanTranslationTable OBJECT-TYPE SYNTAX SEQUENCE OF QinQVlanTranslationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains VLAN translation information." ::= { qinqVLANTranslation 1 } qinqVlanTranslationEntry OBJECT-TYPE SYNTAX QinQVlanTranslationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of VLAN translation information." INDEX {qinqVlanTranslationIfIndex, qinqVlanTranslationCVID} ::= { qinqVlanTranslationTable 1 } QinQVlanTranslationEntry ::= SEQUENCE { qinqVlanTranslationIfIndex InterfaceIndex, qinqVlanTranslationCVID Unsigned32, qinqVlanTranslationSVID Unsigned32, qinqVlanTranslationPriority Integer32, qinqVlanTranslationSVIDOperation INTEGER, qinqVlanTranslationRowStatus RowStatus } qinqVlanTranslationIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index." ::= { qinqVlanTranslationEntry 1 } qinqVlanTranslationCVID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The customer VLAN identifier in a C-TAG." ::= { qinqVlanTranslationEntry 2 } qinqVlanTranslationSVID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "A VLAN identifier conveyed in an S-TAG." ::= { qinqVlanTranslationEntry 3 } qinqVlanTranslationPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The priority of TAG." ::= { qinqVlanTranslationEntry 4 } qinqVlanTranslationSVIDOperation OBJECT-TYPE SYNTAX INTEGER { add(1), replace(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The 'add' action indicates to add a tag for the assigned SP-VLAN before the C-VLAN tag. If there is S-TAG in the packet, this rule will not take effect. The 'replace' action indicates to replace the C-VLAN in the tag by the SP-VLAN. If there is no C-TAG in the packet, this rule will not take effect." ::= { qinqVlanTranslationEntry 5 } qinqVlanTranslationRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { qinqVlanTranslationEntry 99 } -- --------------------------------------------------------------------- -- EOAM Function -- --------------------------------------------------------------------- eoamSystem OBJECT IDENTIFIER ::= { companyEoam 1 } eoamLinkMonitor OBJECT IDENTIFIER ::= { companyEoam 2 } -- ------------------------------------------------------------------ -- The EOAM System Group -- ------------------------------------------------------------------ -- eoamGlobalStatus OBJECT-TYPE -- SYNTAX INTEGER { enabled(1), disabled(2) } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "This object is used to enable/disable the EOAM status." -- ::= { eoamSystem 1 } eoamTable OBJECT-TYPE SYNTAX SEQUENCE OF EOAMConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains EOAM mode information about each port." ::= { eoamSystem 2 } eoamEntry OBJECT-TYPE SYNTAX EOAMConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of EOAM mode information for each port." INDEX { eoamIfIndex } ::= { eoamTable 1 } EOAMConfigEntry ::= SEQUENCE { eoamIfIndex InterfaceIndex, eoamState INTEGER, eoamMode INTEGER, eoamReceivedRemoteLoopback INTEGER, eoamRemoteLoopback INTEGER, eoamDyingGaspEnable INTEGER, eoamCriticalEventEnable INTEGER } eoamIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port. " ::= { eoamEntry 1 } eoamState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM state enabled or disabled." ::= { eoamEntry 2 } eoamMode OBJECT-TYPE SYNTAX INTEGER { passive(1), active(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM mode as active or passive." ::= { eoamEntry 3 } eoamReceivedRemoteLoopback OBJECT-TYPE SYNTAX INTEGER { ignore(1), process(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM received or ignore remote loopback packets." ::= { eoamEntry 4 } eoamRemoteLoopback OBJECT-TYPE SYNTAX INTEGER { noLoopBack(1), startLoopBack(2), remoteLoopBack(3), stopLoopBack(4), localLoopBack(5), unknownLoopBack(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM remote loopback start or stop." ::= { eoamEntry 5 } eoamDyingGaspEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM dying gasp state enabled or disabled." ::= { eoamEntry 6 } eoamCriticalEventEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM critical event state enabled or disabled." ::= { eoamEntry 7 } -- ------------------------------------------------------------------ -- The EOAM Link Monitor Group -- ------------------------------------------------------------------ eoamLinkMonitorTable OBJECT-TYPE SYNTAX SEQUENCE OF EOAMConfigLinkMonitorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains EOAM link monitor information about each port." ::= { eoamLinkMonitor 1 } eoamLinkMonitorEntry OBJECT-TYPE SYNTAX EOAMConfigLinkMonitorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of EOAM link monitor information for each port." INDEX { eoamLinkMonitorIfIndex } ::= { eoamLinkMonitorTable 1 } EOAMConfigLinkMonitorEntry ::= SEQUENCE { eoamLinkMonitorIfIndex InterfaceIndex, errorSymbolNotifyState INTEGER, errorSymbolThreshold Unsigned32, errorSymbolWindow Unsigned32, errorFrameNotifyState INTEGER, errorFrameThreshold Unsigned32, errorFrameWindow Unsigned32, errorFrameSecondsNotifyState INTEGER, errorFrameSecondsThreshold Unsigned32, errorFrameSecondsWindow Unsigned32, errorFramePeriodNotifyState INTEGER, errorFramePeriodThreshold Unsigned32, errorFramePeriodWindow Unsigned32 } eoamLinkMonitorIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port. " ::= { eoamLinkMonitorEntry 1 } errorSymbolNotifyState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM error symbol notify state enabled or disabled." ::= { eoamLinkMonitorEntry 2 } errorSymbolThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM error symbol threshold." ::= { eoamLinkMonitorEntry 3 } errorSymbolWindow OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM error symbol window." ::= { eoamLinkMonitorEntry 4 } errorFrameNotifyState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM error frame notify state enabled or disabled." ::= { eoamLinkMonitorEntry 5 } errorFrameThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM error frame threshold." ::= { eoamLinkMonitorEntry 6 } errorFrameWindow OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM error symbol window." ::= { eoamLinkMonitorEntry 7 } errorFrameSecondsNotifyState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM error symbol notify state enabled or disabled." ::= { eoamLinkMonitorEntry 8 } errorFrameSecondsThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM error symbol threshold." ::= { eoamLinkMonitorEntry 9 } errorFrameSecondsWindow OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM error symbol window." ::= { eoamLinkMonitorEntry 10 } errorFramePeriodNotifyState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM error symbol notify state enabled or disabled." ::= { eoamLinkMonitorEntry 11 } errorFramePeriodThreshold OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM error symbol threshold." ::= { eoamLinkMonitorEntry 12 } errorFramePeriodWindow OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the EOAM error symbol window." ::= { eoamLinkMonitorEntry 13 } -- --------------------------------------------------------------------- -- EOAM Function -- --------------------------------------------------------------------- duldSystem OBJECT IDENTIFIER ::= { companyDuld 1 } -- ------------------------------------------------------------------ -- The DULD System Group -- ------------------------------------------------------------------ duldTable OBJECT-TYPE SYNTAX SEQUENCE OF DULDConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains DULD mode information about each port." ::= { duldSystem 1 } duldEntry OBJECT-TYPE SYNTAX DULDConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of DULD mode information for each port." INDEX { duldIfIndex } ::= { duldTable 1 } DULDConfigEntry ::= SEQUENCE { duldIfIndex InterfaceIndex, duldState INTEGER, duldOperState INTEGER, duldMode INTEGER, duldLinkStatus INTEGER, duldDiscoveryTime Unsigned32 } duldIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port. " ::= { duldEntry 1 } duldState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the DULD admin state enabled or disabled." ::= { duldEntry 2 } duldOperState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Gets the DULD Oper state enabled or disabled." ::= { duldEntry 3 } duldMode OBJECT-TYPE SYNTAX INTEGER { shutdown(1), normal(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the DULD mode as shutdown or normal." ::= { duldEntry 4 } duldLinkStatus OBJECT-TYPE SYNTAX INTEGER { unknow(1), bidirectional(2), txFault(3), rxFault(4), linkDown(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Gets the DULD link status." ::= { duldEntry 5 } duldDiscoveryTime OBJECT-TYPE SYNTAX Unsigned32 (5..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the DULD discovery time." ::= { duldEntry 6 } duldRecoverTime OBJECT-TYPE SYNTAX Integer32 (0 | 60..1000000) MAX-ACCESS read-write STATUS current DESCRIPTION "Duld auto recover time." DEFVAL { 60 } ::= { duldSystem 2 } -- ---------------------------------------------------------- -- The companyDoSCtrl Groups -- ---------------------------------------------------------- -- Dos prevention Group ----------------------------------------------- doSCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF DoSCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that holds the DoS prevention settings of the device." ::= { companyDoSCtrl 1 } doSCtrlEntry OBJECT-TYPE SYNTAX DoSCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of DoS prevention settings of the device." INDEX { doSCtrlType } ::= { doSCtrlTable 1 } DoSCtrlEntry ::= SEQUENCE { doSCtrlType INTEGER, doSCtrlState INTEGER, doSCtrlActionType INTEGER } doSCtrlType OBJECT-TYPE SYNTAX INTEGER { land-attack(1), blat-attack(2), tcp-null-scan(4), tcp-xmascan(5), tcp-synfin(6), tcp-syn-srcport-less-1024(7), ping-death-attack(8), tcp-tiny-fragment(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the DoS prevention type." ::= { doSCtrlEntry 1 } doSCtrlState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of the DoS prevention type." ::= { doSCtrlEntry 2 } doSCtrlActionType OBJECT-TYPE SYNTAX INTEGER { drop(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the action for the DoS prevention type. If this object is set to 'mirror' and DoSCtrlState is set to 'enable', the configuration will not take effect until a valid mirror port is specified. If mirror port is not valid the behavior will be the same as 'drop'" ::= { doSCtrlEntry 3 } dosCtrlTrapLogState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Dos Trap Log function. Default is disabled." DEFVAL { disabled } ::= { companyDoSCtrl 2 } -- ------------------------------------------------------------------ -- The Time Range Setting -- ------------------------------------------------------------------ swTimeRangeSettingTable OBJECT-TYPE SYNTAX SEQUENCE OF SwTimeRangeSettingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to configure time Range in the system." ::= { companyTimeRangeMgmt 1 } swTimeRangeSettingEntry OBJECT-TYPE SYNTAX SwTimeRangeSettingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A schedule entry to configure time Range in the system." INDEX { swTimeRangeIndex } ::= { swTimeRangeSettingTable 1 } SwTimeRangeSettingEntry ::= SEQUENCE { swTimeRangeIndex Integer32, swTimeRangeName DisplayString, swTimeRangeDate INTEGER, swTimeRangeStartYear INTEGER, swTimeRangeStartMonth INTEGER, swTimeRangeStartDay Integer32, swTimeRangeStartHour Integer32, swTimeRangeStartMinute Integer32, swTimeRangeEndYear INTEGER, swTimeRangeEndMonth INTEGER, swTimeRangeEndDay Integer32, swTimeRangeEndHour Integer32, swTimeRangeEndMinute Integer32, swTimeRangeMonday INTEGER, swTimeRangeTuesday INTEGER, swTimeRangeWednesday INTEGER, swTimeRangeThursday INTEGER, swTimeRangeFriday INTEGER, swTimeRangeSaturday INTEGER, swTimeRangeSunday INTEGER, swTimeRangeRowStatus RowStatus } swTimeRangeIndex OBJECT-TYPE SYNTAX Integer32 (1..52) MAX-ACCESS read-only STATUS current DESCRIPTION "The Time Range identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 52." ::= { swTimeRangeSettingEntry 1 } swTimeRangeName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Schedule name associated with the Schedule entry (e.g., `abc, bbb')." ::= { swTimeRangeSettingEntry 2} swTimeRangeDate OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable date range checking while executing time base PoE." ::= { swTimeRangeSettingEntry 3} swTimeRangeStartYear OBJECT-TYPE SYNTAX INTEGER { y2009(2009), y2010(2010), y2011(2011), y2012(2012), y2013(2013), y2014(2014), y2015(2015), y2016(2016), y2017(2017), y2018(2018), y2019(2019), y2020(2020), y2021(2021), y2022(2022), y2023(2023), y2024(2024), y2025(2025), y2026(2026), y2027(2027), y2028(2028), y2029(2029), y2030(2030), y2031(2031), y2032(2032), y2033(2033), y2034(2034), y2035(2035), y2036(2036), y2037(2037) } MAX-ACCESS read-write STATUS current DESCRIPTION "Start year of the Schedule entry." ::= { swTimeRangeSettingEntry 4 } swTimeRangeStartMonth OBJECT-TYPE SYNTAX INTEGER { january(1), february(2), march(3), april(4), may(5), june(6), july(7), august(8), september(9), october(10), november(11), december(12) } MAX-ACCESS read-write STATUS current DESCRIPTION "Start month of the Schedule entry." ::= { swTimeRangeSettingEntry 5 } swTimeRangeStartDay OBJECT-TYPE SYNTAX Integer32 (1..31) MAX-ACCESS read-write STATUS current DESCRIPTION "Start day of the Schedule entry. The value must be from 1 to 31." ::= { swTimeRangeSettingEntry 6 } swTimeRangeStartHour OBJECT-TYPE SYNTAX Integer32 (0..23) MAX-ACCESS read-write STATUS current DESCRIPTION "Start hour of the Schedule entry. The value must be from 0 to 23." ::= { swTimeRangeSettingEntry 7 } swTimeRangeStartMinute OBJECT-TYPE SYNTAX Integer32 (0..59) MAX-ACCESS read-write STATUS current DESCRIPTION "Start minute of the Schedule entry. The value must be from 0 to 59." ::= { swTimeRangeSettingEntry 8 } swTimeRangeEndYear OBJECT-TYPE SYNTAX INTEGER { y2009(2009), y2010(2010), y2011(2011), y2012(2012), y2013(2013), y2014(2014), y2015(2015), y2016(2016), y2017(2017), y2018(2018), y2019(2019), y2020(2020), y2021(2021), y2022(2022), y2023(2023), y2024(2024), y2025(2025), y2026(2026), y2027(2027), y2028(2028), y2029(2029), y2030(2030), y2031(2031), y2032(2032), y2033(2033), y2034(2034), y2035(2035), y2036(2036), y2037(2037) } MAX-ACCESS read-write STATUS current DESCRIPTION "End year of the Schedule entry." ::= { swTimeRangeSettingEntry 9 } swTimeRangeEndMonth OBJECT-TYPE SYNTAX INTEGER { january(1), february(2), march(3), april(4), may(5), june(6), july(7), august(8), september(9), october(10), november(11), december(12) } MAX-ACCESS read-write STATUS current DESCRIPTION "End month of the Schedule entry." ::= { swTimeRangeSettingEntry 10 } swTimeRangeEndDay OBJECT-TYPE SYNTAX Integer32 (1..31) MAX-ACCESS read-write STATUS current DESCRIPTION "End day of the Schedule entry. The value must be from 1 to 31." ::= { swTimeRangeSettingEntry 11 } swTimeRangeEndHour OBJECT-TYPE SYNTAX Integer32 (0..23) MAX-ACCESS read-write STATUS current DESCRIPTION "End hour of the Schedule entry. The value must be from 0 to 23." ::= { swTimeRangeSettingEntry 12 } swTimeRangeEndMinute OBJECT-TYPE SYNTAX Integer32 (0..59) MAX-ACCESS read-write STATUS current DESCRIPTION "End minute of the Schedule entry. The value must be from 0 to 59." ::= { swTimeRangeSettingEntry 13 } swTimeRangeMonday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Monday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 14 } swTimeRangeTuesday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Tuesday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 15 } swTimeRangeWednesday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Wednesday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 16 } swTimeRangeThursday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Thursday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 17 } swTimeRangeFriday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Friday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 18 } swTimeRangeSaturday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Saturday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 19 } swTimeRangeSunday OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disble scheduling Sunday." DEFVAL { disable } ::= { swTimeRangeSettingEntry 20 } swTimeRangeRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of an entry in the Time Range Information Table. Only a subset of the rowstatus variables (active, notinservice, createAndWait, destroy) are available." ::= { swTimeRangeSettingEntry 21 } -- -- LLDP Settings -- dlinklldpState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used for enabling or disabling LLDP in the system." DEFVAL { disable } ::= { companyLLDPSetting 1 } dlinklldpMsgHoldMultiplier OBJECT-TYPE SYNTAX INTEGER (2..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The time-to-live value expressed as a multiple of the lldpMessageTxInterval object.The actual time-to-live value used in LLDP frames, transmitted on behalf of this LLDP agent, can be expressed by the following formula: TTL = min(65535, (lldpMessageTxInterval * lldpMessageTxHoldMultiplier))" --DEFVAL { 4 } ::= { companyLLDPSetting 2 } dlinklldpMsgTxInterval OBJECT-TYPE SYNTAX INTEGER (5..32768) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used for LLDP packet update frequency. The timer in units of seconds." --DEFVAL { 30 } ::= { companyLLDPSetting 3 } dlinklldpReinitDelay OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used for LLDP Reinitialization Delay. The timer in units of seconds." --DEFVAL { 2 } ::= { companyLLDPSetting 4 } dlinklldpTxDelay OBJECT-TYPE SYNTAX INTEGER (1..8192) MAX-ACCESS read-write STATUS current DESCRIPTION "The lldpTxDelay indicates the delay (in units of seconds) between successive LLDP frame transmissions initiated by value/status changes in the LLDP local systems MIB. The recommended value for the lldpTxDelay is set by the following formula: 1 <= lldpTxDelay <= (0.25 * lldpMessageTxInterval)." --DEFVAL { 2 } ::= { companyLLDPSetting 5 } -- -- lldpManAddrConfigTxPortsTable : selection of management addresses -- to be transmitted on a specified set -- of ports. -- dlinklldpConfigManAddrPortsTxEnable OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "A set of ports that are identified by a PortList, in which each port is represented as a bit. The corresponding local system management address instance will be transmitted on the member ports of the lldpManAddrPortsTxEnable. The default value for lldpConfigManAddrPortsTxEnable object is empty binary string, which means no ports are specified for advertising indicated management address instance." REFERENCE "IEEE 802.1AB-2005 10.2.1.1" ::= { companyLLDPSetting 6 } -- -- D-Link Defined LLDP Port Configuration Table -- -- textual conventions LldpPortNumber ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "Each port contained in the chassis (that is known to the LLDP agent) is uniquely identified by a port number. A port number has no mandatory relationship to an InterfaceIndex object (of the interfaces MIB, IETF RFC 2863). If the LLDP agent is a IEEE 802.1D, IEEE 802.1Q bridge, the LldpPortNumber will have the same value as the dot1dBasePort object (defined in IETF RFC 1493) associated corresponding bridge port. If the system hosting LLDP agent is not an IEEE 802.1D or an IEEE 802.1Q bridge, the LldpPortNumber will have the same value as the corresponding interface's InterfaceIndex object. Port numbers should be in the range of 1 and 4096 since a particular port is also represented by the corresponding port number bit in LldpPortList." SYNTAX Integer32(1..4096) -- textual conventions end lldpPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table that controls LLDP frame transmission on individual ports." ::= { companyLLDPSetting 11 } lldpPortConfigEntry OBJECT-TYPE SYNTAX LldpPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP configuration information for a particular port. This configuration parameter controls the transmission and the reception of LLDP frames on those ports whose rows are created in this table." INDEX { lldpPortConfigPortNum } ::= { lldpPortConfigTable 1 } LldpPortConfigEntry ::= SEQUENCE { lldpPortConfigPortNum LldpPortNumber, lldpPortConfigAdminStatus INTEGER, lldpPortConfigNotificationEnable TruthValue, lldpPortConfigTLVsTxEnable BITS } lldpPortConfigPortNum OBJECT-TYPE SYNTAX LldpPortNumber MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The value of this object is used as a port index to the lldpPortConfigTable." ::= { lldpPortConfigEntry 1 } lldpPortConfigAdminStatus OBJECT-TYPE SYNTAX INTEGER { txOnly(1), rxOnly(2), txAndRx(3), disabled(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The administratively desired status of the local LLDP agent. If the associated lldpPortConfigAdminStatus object has a value of 'txOnly(1)', then LLDP agent will transmit LLDP frames on this port and it will not store any information about the remote systems connected. If the associated lldpPortConfigAdminStatus object has a value of 'rxOnly(2)', then the LLDP agent will receive, but it will not transmit LLDP frames on this port. If the associated lldpPortConfigAdminStatus object has a value of 'txAndRx(3)', then the LLDP agent will transmit and receive LLDP frames on this port. If the associated lldpPortConfigAdminStatus object has a value of 'disabled(4)', then LLDP agent will not transmit or receive LLDP frames on this port. If there is remote systems information which is received on this port and stored in other tables, before the port's lldpPortConfigAdminStatus becomes disabled, then the information will naturally age out." REFERENCE "IEEE 802.1AB-2005 10.5.1" DEFVAL { txAndRx } ::= { lldpPortConfigEntry 2 } lldpPortConfigNotificationEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The lldpPortConfigNotificationEnable controls, on a per port basis, whether or not notifications from the agent are enabled. The value true(1) means that notifications are enabled; the value false(2) means that they are not." DEFVAL { false } ::= { lldpPortConfigEntry 3 } lldpPortConfigTLVsTxEnable OBJECT-TYPE SYNTAX BITS { portDesc(0), sysName(1), sysDesc(2), sysCap(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The lldpPortConfigTLVsTxEnable, defined as a bitmap, includes the basic set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to a TLV type associated with a specific optional TLV. It should be noted that the organizationally-specific TLVs are excluded from the lldpTLVsTxEnable bitmap. LLDP Organization Specific Information Extension MIBs should have similar configuration object to control transmission of their organizationally defined TLVs. The bit 'portDesc(0)' indicates that LLDP agent should transmit 'Port Description TLV'. The bit 'sysName(1)' indicates that LLDP agent should transmit 'System Name TLV'. The bit 'sysDesc(2)' indicates that LLDP agent should transmit 'System Description TLV'. The bit 'sysCap(3)' indicates that LLDP agent should transmit 'System Capabilities TLV'. There is no bit reserved for the management address TLV type since transmission of management address TLVs are controlled by another object, lldpConfigManAddrTable. The default value for lldpPortConfigTLVsTxEnable object is empty set, which means no enumerated values are set. The value of this object must be restored from non-volatile storage after a re-initialization of the management system." REFERENCE "IEEE 802.1AB-2005 10.2.1.1" -- DEFVAL { { } } ::= { lldpPortConfigEntry 4 } -- -- D-Link Defined LLDP Extension Dot3 MIB Objects -- lldpXdot3Objects OBJECT IDENTIFIER ::= { companyLLDPSetting 12 } -- LLDP IEEE 802.3 extension MIB groups lldpXdot3Config OBJECT IDENTIFIER ::= { lldpXdot3Objects 1 } lldpXdot3LocalData OBJECT IDENTIFIER ::= { lldpXdot3Objects 2 } lldpXdot3RemoteData OBJECT IDENTIFIER ::= { lldpXdot3Objects 3 } -- textual conventions LldpPowerPortClass ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This TC describes the Power over Ethernet (PoE) port class." SYNTAX INTEGER { pClassPSE(1), pClassPD(2) } LldpLinkAggStatusMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This TC describes the link aggregation status. The bit 'aggCapable(0)' indicates the link is capable of being aggregated. The bit 'aggEnabled(1)' indicates the link is currently in aggregation." SYNTAX BITS { aggCapable(0), aggEnabled(1) } ------------------------------------------------------------------------------ -- IEEE 802.3 - Configuration ------------------------------------------------------------------------------ lldpXdot3PortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot3PortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that controls selection of LLDP TLVs to be transmitted on individual ports." ::= { lldpXdot3Config 1 } lldpXdot3PortConfigEntry OBJECT-TYPE SYNTAX LldpXdot3PortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP configuration information that controls the transmission of IEEE 802.3 organizationally defined TLVs on LLDP transmission capable ports. This configuration object augments the lldpPortConfigEntry of the LLDP-MIB, therefore it is only present along with the port configuration defined by the associated lldpPortConfigEntry entry. Each active lldpXdot3PortConfigEntry must be from non-volatile storage (along with the corresponding lldpPortConfigEntry) after a re-initialization of the management system." AUGMENTS { lldpPortConfigEntry } ::= { lldpXdot3PortConfigTable 1 } LldpXdot3PortConfigEntry ::= SEQUENCE { lldpXdot3PortConfigTLVsTxEnable BITS } lldpXdot3PortConfigTLVsTxEnable OBJECT-TYPE SYNTAX BITS { macPhyConfigStatus(0), powerViaMDI(1), linkAggregation(2), maxFrameSize(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The lldpXdot3PortConfigTLVsTxEnable, defined as a bitmap, includes the IEEE 802.3 organizationally defined set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to an IEEE 802.3 subtype associated with a specific IEEE 802.3 optional TLV. The bit 0 is not used since there is no corresponding subtype. The bit 'macPhyConfigStatus(0)' indicates that LLDP agent should transmit 'MAC/PHY configuration/status TLV'. The bit 'powerViaMDI(1)' indicates that LLDP agent should transmit 'Power via MDI TLV'. The bit 'linkAggregation(2)' indicates that LLDP agent should transmit 'Link Aggregation TLV'. The bit 'maxFrameSize(3)' indicates that LLDP agent should transmit 'Maximum-frame-size TLV'. The default value for lldpXdot3PortConfigTLVsTxEnable object is an empty set, which means no enumerated values are set. The value of this object must be restored from non-volatile storage after a re-initialization of the management system." REFERENCE "IEEE 802.1AB-2005 10.2.1.1" -- DEFVAL { { } } ::= { lldpXdot3PortConfigEntry 1 } ------------------------------------------------------------------------------ -- IEEE 802.3 - Local Device Information ------------------------------------------------------------------------------ --- --- lldpXdot3LocPortTable: Ethernet Port AutoNeg/Speed/Duplex --- Information Table --- --- lldpXdot3LocPortTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot3LocPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per port of Ethernet port information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent." ::= { lldpXdot3LocalData 1 } lldpXdot3LocPortEntry OBJECT-TYPE SYNTAX LldpXdot3LocPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular port component." INDEX { lldpXdot3LocPortAutoNegSupported } ::= { lldpXdot3LocPortTable 1 } LldpXdot3LocPortEntry ::= SEQUENCE { lldpXdot3LocPortAutoNegSupported TruthValue, lldpXdot3LocPortAutoNegEnabled TruthValue, lldpXdot3LocPortAutoNegAdvertisedCap OCTET STRING, lldpXdot3LocPortOperMauType Integer32 } lldpXdot3LocPortAutoNegSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether the given port (associated with the local system) supports Auto-negotiation." REFERENCE "IEEE 802.1AB-2005 G.2.1" ::= { lldpXdot3LocPortEntry 1 } lldpXdot3LocPortAutoNegEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether port Auto-negotiation is enabled on the given port associated with the local system." REFERENCE "IEEE 802.1AB-2005 G.2.1" ::= { lldpXdot3LocPortEntry 2 } lldpXdot3LocPortAutoNegAdvertisedCap OBJECT-TYPE SYNTAX OCTET STRING(SIZE(2)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value (bitmap) of the ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC 3636) which is associated with the given port on the local system." REFERENCE "IEEE 802.1AB-2005 G.2.2" ::= { lldpXdot3LocPortEntry 3 } lldpXdot3LocPortOperMauType OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "An integer value that indicates the operational MAU type of the given port on the local system. This object contains the integer value derived from the list position of the corresponding dot3MauType as listed in IETF RFC 3636 (or subsequent revisions) and is equal to the last number in the respective dot3MauType OID. For example, if the ifMauType object is dot3MauType1000BaseTHD which corresponds to {dot3MauType 29}, the numerical value of this field will be 29. For MAU types not listed in RFC 3636 (or subsequent revisions), the value of this field shall be set to zero." REFERENCE "IEEE 802.1AB-2005 G.2.3" ::= { lldpXdot3LocPortEntry 4 } --- --- --- lldpXdot3LocPowerTable: Power Ethernet Information Table --- --- lldpXdot3LocPowerTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot3LocPowerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per port of power ethernet information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent." ::= { lldpXdot3LocalData 2 } lldpXdot3LocPowerEntry OBJECT-TYPE SYNTAX LldpXdot3LocPowerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular port component." INDEX { lldpXdot3LocPowerPortClass } ::= { lldpXdot3LocPowerTable 1 } LldpXdot3LocPowerEntry ::= SEQUENCE { lldpXdot3LocPowerPortClass LldpPowerPortClass, lldpXdot3LocPowerMDISupported TruthValue, lldpXdot3LocPowerMDIEnabled TruthValue, lldpXdot3LocPowerPairControlable TruthValue, lldpXdot3LocPowerPairs Integer32, lldpXdot3LocPowerClass Integer32 } lldpXdot3LocPowerPortClass OBJECT-TYPE SYNTAX LldpPowerPortClass MAX-ACCESS read-only STATUS current DESCRIPTION "The value that identifies the port Class of the given port associated with the local system." REFERENCE "IEEE 802.1AB-2005 G.3.1" ::= { lldpXdot3LocPowerEntry 1 } lldpXdot3LocPowerMDISupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether the MDI power is supported on the given port associated with the local system." REFERENCE "IEEE 802.1AB-2005 G.3.1" ::= { lldpXdot3LocPowerEntry 2 } lldpXdot3LocPowerMDIEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to identify whether MDI power is enabled on the given port associated with the local system." REFERENCE "IEEE 802.1AB-2005 G.3.1" ::= { lldpXdot3LocPowerEntry 3 } lldpXdot3LocPowerPairControlable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value is derived from the value of pethPsePortPowerPairsControlAbility object (defined in IETF RFC 3621) and is used to indicate whether the pair selection can be controlled on the given port associated with the local system." REFERENCE "IEEE 802.1AB-2005 G.3.1" ::= { lldpXdot3LocPowerEntry 4 } lldpXdot3LocPowerPairs OBJECT-TYPE SYNTAX Integer32(1|2) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the pethPsePortPowerPairs object (defined in IETF RFC 3621) which is associated with the given port on the local system." REFERENCE "IEEE 802.1AB-2005 G.3.2" ::= { lldpXdot3LocPowerEntry 5 } lldpXdot3LocPowerClass OBJECT-TYPE SYNTAX Integer32(1|2|3|4|5) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the pethPsePortPowerClassifications object (defined in IETF RFC 3621) which is associated with the given port on the local system." REFERENCE "IEEE 802.1AB-2005 G.3.3" ::= { lldpXdot3LocPowerEntry 6 } --- --- --- lldpXdot3LocLinkAggTable: Link Aggregation Information Table --- --- lldpXdot3LocLinkAggTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot3LocLinkAggEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per port of link aggregation information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent." ::= { lldpXdot3LocalData 3 } lldpXdot3LocLinkAggEntry OBJECT-TYPE SYNTAX LldpXdot3LocLinkAggEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Link Aggregation information about a particular port component." INDEX { lldpXdot3LocLinkAggStatus } ::= { lldpXdot3LocLinkAggTable 1 } LldpXdot3LocLinkAggEntry ::= SEQUENCE { lldpXdot3LocLinkAggStatus LldpLinkAggStatusMap, lldpXdot3LocLinkAggPortId Integer32 } lldpXdot3LocLinkAggStatus OBJECT-TYPE SYNTAX LldpLinkAggStatusMap MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap value contains the link aggregation capabilities and the current aggregation status of the link." REFERENCE "IEEE 802.1AB-2005 G.4.1" ::= { lldpXdot3LocLinkAggEntry 1 } lldpXdot3LocLinkAggPortId OBJECT-TYPE SYNTAX Integer32(0|1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the IEEE 802.3 aggregated port identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1), derived from the ifNumber of the ifIndex for the port component in link aggregation. If the port is not in link aggregation state and/or it does not support link aggregation, this value should be set to zero." REFERENCE "IEEE 802.1AB-2005 G.4.2" ::= { lldpXdot3LocLinkAggEntry 2 } --- --- --- lldpXdot3LocMaxFrameSizeTable: Maximum Frame Size information --- --- lldpXdot3LocMaxFrameSizeTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot3LocMaxFrameSizeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per port of maximum frame size information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent." ::= { lldpXdot3LocalData 4 } lldpXdot3LocMaxFrameSizeEntry OBJECT-TYPE SYNTAX LldpXdot3LocMaxFrameSizeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Maximum Frame Size information about a particular port component." INDEX { lldpXdot3LocMaxFrameSize } ::= { lldpXdot3LocMaxFrameSizeTable 1 } LldpXdot3LocMaxFrameSizeEntry ::= SEQUENCE { lldpXdot3LocMaxFrameSize Integer32 } lldpXdot3LocMaxFrameSize OBJECT-TYPE SYNTAX Integer32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "An integer value indicating the maximum supported frame size in octets on the given port of the local system." REFERENCE "IEEE 802.1AB-2005 G.5.1" ::= { lldpXdot3LocMaxFrameSizeEntry 1 } ------------------------------------------------------------------------------ -- IEEE 802.3 - Remote Devices Information ------------------------------------------------------------------------------ --- --- --- lldpXdot3RemPortTable: Ethernet Information Table --- --- lldpXdot3RemPortTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot3RemPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Ethernet port information (as a part of the LLDP 802.3 organizational extension) of the remote system." ::= { lldpXdot3RemoteData 1 } lldpXdot3RemPortEntry OBJECT-TYPE SYNTAX LldpXdot3RemPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular physical network connection." INDEX { lldpXdot3RemPortAutoNegSupported } ::= { lldpXdot3RemPortTable 1 } LldpXdot3RemPortEntry ::= SEQUENCE { lldpXdot3RemPortAutoNegSupported TruthValue, lldpXdot3RemPortAutoNegEnabled TruthValue, lldpXdot3RemPortAutoNegAdvertisedCap OCTET STRING, lldpXdot3RemPortOperMauType Integer32 } lldpXdot3RemPortAutoNegSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether the given port (associated with remote system) supports Auto-negotiation." REFERENCE "IEEE 802.1AB-2005 G.2.1" ::= { lldpXdot3RemPortEntry 1 } lldpXdot3RemPortAutoNegEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether port Auto-negotiation is enabled on the given port associated with the remote system." REFERENCE "IEEE 802.1AB-2005 G.2.1" ::= { lldpXdot3RemPortEntry 2 } lldpXdot3RemPortAutoNegAdvertisedCap OBJECT-TYPE SYNTAX OCTET STRING(SIZE(2)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value (bitmap) of the ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC 3636) which is associated with the given port on the remote system." REFERENCE "IEEE 802.1AB-2005 G.2.2" ::= { lldpXdot3RemPortEntry 3 } lldpXdot3RemPortOperMauType OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "An integer value that indicates the operational MAU type of the sending device. This object contains the integer value derived from the list position of the corresponding dot3MauType as listed in in IETF RFC 3636 (or subsequent revisions) and is equal to the last number in the respective dot3MauType OID. For example, if the ifMauType object is dot3MauType1000BaseTHD which corresponds to {dot3MauType 29}, the numerical value of this field will be 29. For MAU types not listed in RFC 3636 (or subsequent revisions), the value of this field shall be set to zero." REFERENCE "IEEE 802.1AB-2005 G.2.3" ::= { lldpXdot3RemPortEntry 4 } --- --- --- lldpXdot3RemPowerTable: Power Ethernet Information Table --- --- lldpXdot3RemPowerTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot3RemPowerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Ethernet power information (as a part of the LLDP 802.3 organizational extension) of the remote system." ::= { lldpXdot3RemoteData 2 } lldpXdot3RemPowerEntry OBJECT-TYPE SYNTAX LldpXdot3RemPowerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular physical network connection." INDEX { lldpXdot3RemPowerPortClass} ::= { lldpXdot3RemPowerTable 1 } LldpXdot3RemPowerEntry ::= SEQUENCE { lldpXdot3RemPowerPortClass LldpPowerPortClass, lldpXdot3RemPowerMDISupported TruthValue, lldpXdot3RemPowerMDIEnabled TruthValue, lldpXdot3RemPowerPairControlable TruthValue, lldpXdot3RemPowerPairs Integer32, lldpXdot3RemPowerClass Integer32 } lldpXdot3RemPowerPortClass OBJECT-TYPE SYNTAX LldpPowerPortClass MAX-ACCESS read-only STATUS current DESCRIPTION "The value that identifies the port Class of the given port associated with the remote system." REFERENCE "IEEE 802.1AB-2005 G.3.1" ::= { lldpXdot3RemPowerEntry 1 } lldpXdot3RemPowerMDISupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether the MDI power is supported on the given port associated with the remote system." REFERENCE "IEEE 802.1AB-2005 G.3.1" ::= { lldpXdot3RemPowerEntry 2 } lldpXdot3RemPowerMDIEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to identify whether MDI power is enabled on the given port associated with the remote system." REFERENCE "IEEE 802.1AB-2005 G.3.1" ::= { lldpXdot3RemPowerEntry 3 } lldpXdot3RemPowerPairControlable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value is derived from the value of pethPsePortPowerPairsControlAbility object (defined in IETF RFC 3621) and is used to indicate whether the pair selection can be controlled on the given port associated with the remote system." REFERENCE "IEEE 802.1AB-2005 G.3.1" ::= { lldpXdot3RemPowerEntry 4 } lldpXdot3RemPowerPairs OBJECT-TYPE SYNTAX Integer32(1|2) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the pethPsePortPowerPairs object (defined in IETF RFC 3621) which is associated with the given port on the remote system." REFERENCE "IEEE 802.1AB-2005 G.3.2" ::= { lldpXdot3RemPowerEntry 5 } lldpXdot3RemPowerClass OBJECT-TYPE SYNTAX Integer32(1|2|3|4|5) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the value of the pethPsePortPowerClassifications object (defined in IETF RFC 3621) which is associated with the given port on the remote system." REFERENCE "IEEE 802.1AB-2005 G.3.3" ::= { lldpXdot3RemPowerEntry 6 } --- --- --- lldpXdot3RemLinkAggTable: Link Aggregation Information Table --- --- lldpXdot3RemLinkAggTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot3RemLinkAggEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains port link aggregation information (as a part of the LLDP 802.3 organizational extension) of the remote system." ::= { lldpXdot3RemoteData 3 } lldpXdot3RemLinkAggEntry OBJECT-TYPE SYNTAX LldpXdot3RemLinkAggEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Link Aggregation information about remote system's port component." INDEX { lldpXdot3RemLinkAggStatus } ::= { lldpXdot3RemLinkAggTable 1 } LldpXdot3RemLinkAggEntry ::= SEQUENCE { lldpXdot3RemLinkAggStatus LldpLinkAggStatusMap, lldpXdot3RemLinkAggPortId Integer32 } lldpXdot3RemLinkAggStatus OBJECT-TYPE SYNTAX LldpLinkAggStatusMap MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap value contains the link aggregation capabilities and the current aggregation status of the link." REFERENCE "IEEE 802.1AB-2005 G.4.1" ::= { lldpXdot3RemLinkAggEntry 1 } lldpXdot3RemLinkAggPortId OBJECT-TYPE SYNTAX Integer32(0|1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the IEEE 802.3 aggregated port identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1), derived from the ifNumber of the ifIndex for the port component associated with the remote system. If the remote port is not in link aggregation state and/or it does not support link aggregation, this value should be zero." REFERENCE "IEEE 802.1AB-2005 G.4.2" ::= { lldpXdot3RemLinkAggEntry 2 } --- --- --- lldpXdot3RemMaxFrameSizeTable: Maximum Frame Size information --- --- lldpXdot3RemMaxFrameSizeTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot3RemMaxFrameSizeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per port of maximum frame size information (as a part of the LLDP 802.3 organizational extension) of the remote system." ::= { lldpXdot3RemoteData 4 } lldpXdot3RemMaxFrameSizeEntry OBJECT-TYPE SYNTAX LldpXdot3RemMaxFrameSizeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Maximum Frame Size information about a particular port component." INDEX { lldpXdot3RemMaxFrameSize } ::= { lldpXdot3RemMaxFrameSizeTable 1 } LldpXdot3RemMaxFrameSizeEntry ::= SEQUENCE { lldpXdot3RemMaxFrameSize Integer32 } lldpXdot3RemMaxFrameSize OBJECT-TYPE SYNTAX Integer32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "An integer value indicating the maximum supported frame size in octets on the port component associated with the remote system." REFERENCE "IEEE 802.1AB-2005 G.5.1" ::= { lldpXdot3RemMaxFrameSizeEntry 1 } -- -- D-Link Defined LLDP Extension Dot1 MIB Objects -- lldpXdot1Objects OBJECT IDENTIFIER ::= { companyLLDPSetting 13 } -- LLDP IEEE 802.1 extension MIB groups lldpXdot1Config OBJECT IDENTIFIER ::= { lldpXdot1Objects 1 } lldpXdot1LocalData OBJECT IDENTIFIER ::= { lldpXdot1Objects 2 } lldpXdot1RemoteData OBJECT IDENTIFIER ::= { lldpXdot1Objects 3 } ------------------------------------------------------------------------------ -- IEEE 802.1 - Configuration ------------------------------------------------------------------------------ -- -- lldpXdot1ConfigPortVlanTable : configure the transmission of the -- Port VLAN-ID TLVs on set of ports. -- lldpXdot1ConfigPortVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1ConfigPortVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that controls selection of LLDP Port VLAN-ID TLVs to be transmitted on individual ports." ::= { lldpXdot1Config 1 } lldpXdot1ConfigPortVlanEntry OBJECT-TYPE SYNTAX LldpXdot1ConfigPortVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP configuration information that controls the transmission of IEEE 802.1 organizationally defined Port VLAN-ID TLV on LLDP transmission capable ports. This configuration object augments the lldpPortConfigEntry of the LLDP-MIB, therefore it is only present along with the port configuration defined by the associated lldpPortConfigEntry entry. Each active lldpConfigEntry must be restored from non-volatile storage (along with the corresponding lldpPortConfigEntry) after a re-initialization of the management system." AUGMENTS { lldpPortConfigEntry } ::= { lldpXdot1ConfigPortVlanTable 1 } LldpXdot1ConfigPortVlanEntry ::= SEQUENCE { lldpXdot1ConfigPortVlanTxEnable TruthValue } lldpXdot1ConfigPortVlanTxEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The lldpXdot1ConfigPortVlanTxEnable, which is defined as a truth value and configured by the network management, determines whether the IEEE 802.1 organizationally defined port VLAN TLV transmission is allowed on a given LLDP transmission capable port. The value of this object must be restored from non-volatile storage after a re-initialization of the management system." REFERENCE "IEEE 802.1AB-2005 10.2.1.1" DEFVAL { false } ::= { lldpXdot1ConfigPortVlanEntry 1 } -- -- lldpXdot1LocVlanNameTable : VLAN name information about the local system -- lldpXdot1LocVlanNameTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1LocVlanNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per IEEE 802.1Q VLAN name information on the local system known to this agent." ::= { lldpXdot1LocalData 3 } lldpXdot1LocVlanNameEntry OBJECT-TYPE SYNTAX LldpXdot1LocVlanNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1LocVlanId, configured on the given port." INDEX { lldpXdot1LocVlanId } ::= { lldpXdot1LocVlanNameTable 1 } LldpXdot1LocVlanNameEntry ::= SEQUENCE { lldpXdot1LocVlanId VlanId, lldpXdot1LocVlanName SnmpAdminString } lldpXdot1LocVlanId OBJECT-TYPE SYNTAX VlanId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port is compatible." REFERENCE "IEEE 802.1AB-2005 F.4.2" ::= { lldpXdot1LocVlanNameEntry 1 } lldpXdot1LocVlanName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The string value used to identify VLAN name identified by the Vlan Id associated with the given port on the local system. This object should contain the value of the dot1QVLANStaticName object (defined in IETF RFC 2674) identified with the given lldpXdot1LocVlanId." REFERENCE "IEEE 802.1AB-2005 F.4.4" ::= { lldpXdot1LocVlanNameEntry 2 } -- -- lldpXdot1ConfigVlanNameTable : configure the transmission of the -- VLAN name instances on set of ports. -- lldpXdot1ConfigVlanNameTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1ConfigVlanNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table that controls selection of LLDP VLAN name TLV instances to be transmitted on individual ports." ::= { lldpXdot1Config 2 } lldpXdot1ConfigVlanNameEntry OBJECT-TYPE SYNTAX LldpXdot1ConfigVlanNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System VLAN name instance will be transmitted. This configuration object augments the lldpLocVlanEntry, therefore it is only present along with the VLAN Name instance contained in the associated lldpLocVlanNameEntry entry. Each active lldpXdot1ConfigVlanNameEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocVlanNameEntry) after a re-initialization of the management system." AUGMENTS { lldpXdot1LocVlanNameEntry } ::= { lldpXdot1ConfigVlanNameTable 1 } LldpXdot1ConfigVlanNameEntry ::= SEQUENCE { lldpXdot1ConfigVlanNameTxEnable TruthValue } lldpXdot1ConfigVlanNameTxEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The boolean value that indicates whether the corresponding Local System VLAN name instance will be transmitted on the port defined by the given lldpXdot1LocVlanNameEntry. The value of this object must be restored from non-volatile storage after a re-initialization of the management system." REFERENCE "IEEE 802.1AB-2005 10.2.1.1" DEFVAL { false } ::= { lldpXdot1ConfigVlanNameEntry 1 } -- -- lldpXdot1LocProtoVlanTable: Port and Protocol VLAN information -- lldpXdot1LocProtoVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1LocProtoVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per Port and Protocol VLAN information about the local system." ::= { lldpXdot1LocalData 2 } lldpXdot1LocProtoVlanEntry OBJECT-TYPE SYNTAX LldpXdot1LocProtoVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Port and protocol VLAN ID Information about a particular port component. There may be multiple port and protocol VLANs, identified by a particular lldpXdot1LocProtoVlanId, configured on the given port." INDEX { lldpXdot1LocProtoVlanId } ::= { lldpXdot1LocProtoVlanTable 1 } LldpXdot1LocProtoVlanEntry ::= SEQUENCE { lldpXdot1LocProtoVlanId Integer32, lldpXdot1LocProtoVlanSupported TruthValue, lldpXdot1LocProtoVlanEnabled TruthValue } lldpXdot1LocProtoVlanId OBJECT-TYPE SYNTAX Integer32(0|1..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The integer value used to identify the port and protocol VLANs associated with the given port associated with the local system. A value of zero shall be used if the system either does not know the protocol VLAN ID (PPVID) or does not support port and protocol VLAN operation." REFERENCE "IEEE 802.1AB-2005 F.3.2" ::= { lldpXdot1LocProtoVlanEntry 1 } lldpXdot1LocProtoVlanSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether the given port (associated with the local system) supports port and protocol VLANs." REFERENCE "IEEE 802.1AB-2005 F.3.1" ::= { lldpXdot1LocProtoVlanEntry 2 } lldpXdot1LocProtoVlanEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the local system." REFERENCE "IEEE 802.1AB-2005 F.3.1" ::= { lldpXdot1LocProtoVlanEntry 3 } -- -- lldpXdot1ConfigProtoVlanTable : configure the transmission of the -- protocol VLAN instances on set -- of ports. -- lldpXdot1ConfigProtoVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1ConfigProtoVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table that controls selection of LLDP Port and Protocol VLAN ID TLV instances to be transmitted on individual ports." ::= { lldpXdot1Config 3 } lldpXdot1ConfigProtoVlanEntry OBJECT-TYPE SYNTAX LldpXdot1ConfigProtoVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol VLAN instance will be transmitted. This configuration object augments the lldpXdot1LocVlanEntry, therefore it is only present along with the Port and Protocol VLAN ID instance contained in the associated lldpXdot1LocVlanEntry entry. Each active lldpXdot1ConfigProtoVlanEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocProtoVlanEntry) after a re-initialization of the management system." AUGMENTS { lldpXdot1LocProtoVlanEntry } ::= { lldpXdot1ConfigProtoVlanTable 1 } LldpXdot1ConfigProtoVlanEntry ::= SEQUENCE { lldpXdot1ConfigProtoVlanTxEnable TruthValue } lldpXdot1ConfigProtoVlanTxEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The boolean value that indicates whether the corresponding Local System Port and Protocol VLAN instance will be transmitted on the port defined by the given lldpXdot1LocProtoVlanEntry. The value of this object must be restored from non-volatile storage after a re-initialization of the management system." REFERENCE "IEEE 802.1AB-2005 10.2.1.1" DEFVAL { false } ::= { lldpXdot1ConfigProtoVlanEntry 1 } -- -- lldpXdot1LocProtocolTable : Protocol Identity information -- lldpXdot1LocProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1LocProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per protocol identity information on the local system known to this agent." REFERENCE "IEEE 802.1AB-2005 F.5" ::= { lldpXdot1LocalData 4 } lldpXdot1LocProtocolEntry OBJECT-TYPE SYNTAX LldpXdot1LocProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about particular protocols that are accessible through the given port component. There may be multiple protocols, identified by particular lldpXdot1ProtocolIndex, and lldpLocPortNum." REFERENCE "IEEE 802.1AB-2005 F.5" INDEX { lldpXdot1LocProtocolIndex } ::= { lldpXdot1LocProtocolTable 1 } LldpXdot1LocProtocolEntry ::= SEQUENCE { lldpXdot1LocProtocolIndex Integer32, lldpXdot1LocProtocolId OCTET STRING } lldpXdot1LocProtocolIndex OBJECT-TYPE SYNTAX Integer32(1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity." ::= { lldpXdot1LocProtocolEntry 1 } lldpXdot1LocProtocolId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The octet string value used to identify the protocols associated with the given port of the local system." REFERENCE "IEEE 802.1AB-2005 F.5.3" ::= { lldpXdot1LocProtocolEntry 2 } -- -- lldpXdot1ConfigProtocolTable : configure the transmission of the -- protocol instances on set -- of ports. -- lldpXdot1ConfigProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1ConfigProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table that controls selection of LLDP Protocol TLV instances to be transmitted on individual ports." ::= { lldpXdot1Config 4 } lldpXdot1ConfigProtocolEntry OBJECT-TYPE SYNTAX LldpXdot1ConfigProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol instance will be transmitted. This configuration object augments the lldpXdot1LocProtoEntry, therefore it is only present along with the Protocol instance contained in the associated lldpXdot1LocProtoEntry entry. Each active lldpXdot1ConfigProtocolEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocProtocolEntry) after a re-initialization of the management system." AUGMENTS { lldpXdot1LocProtocolEntry } ::= { lldpXdot1ConfigProtocolTable 1 } LldpXdot1ConfigProtocolEntry ::= SEQUENCE { lldpXdot1ConfigProtocolTxEnable TruthValue } lldpXdot1ConfigProtocolTxEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The boolean value that indicates whether the corresponding Local System Protocol Identity instance will be transmitted on the port defined by the given lldpXdot1LocProtocolEntry. The value of this object must be restored from non-volatile storage after a re-initialization of the management system." REFERENCE "IEEE 802.1AB-2005 10.2.1.1" DEFVAL { false } ::= { lldpXdot1ConfigProtocolEntry 1 } ------------------------------------------------------------------------------ -- IEEE 802.1 - Local System Information ------------------------------------------------------------------------------ lldpXdot1LocTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1LocEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per port for IEEE 802.1 organizationally defined LLDP extension on the local system known to this agent." ::= { lldpXdot1LocalData 1 } lldpXdot1LocEntry OBJECT-TYPE SYNTAX LldpXdot1LocEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about IEEE 802.1 organizationally defined LLDP extension." INDEX { lldpXdot1LocPortVlanId } ::= { lldpXdot1LocTable 1 } LldpXdot1LocEntry ::= SEQUENCE { lldpXdot1LocPortVlanId Integer32 } lldpXdot1LocPortVlanId OBJECT-TYPE SYNTAX Integer32(0|1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "The integer value used to identify the port's VLAN identifier associated with the local system. A value of zero shall be used if the system either does not know the PVID or does not support port-based VLAN operation." REFERENCE "IEEE 802.1AB-2005 F.2.1" ::= { lldpXdot1LocEntry 1 } ------------------------------------------------------------------------------ -- IEEE 802.1 - Remote System Information ------------------------------------------------------------------------------ lldpXdot1RemTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1RemEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per physical network connection known to this agent. The agent may wish to ensure that only one lldpXdot1RemEntry is present for each local port, or it may choose to maintain multiple lldpXdot1RemEntries for the same local port." ::= { lldpXdot1RemoteData 1 } lldpXdot1RemEntry OBJECT-TYPE SYNTAX LldpXdot1RemEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular port component." INDEX { lldpXdot1RemPortVlanId } ::= { lldpXdot1RemTable 1 } LldpXdot1RemEntry ::= SEQUENCE { lldpXdot1RemPortVlanId Integer32 } lldpXdot1RemPortVlanId OBJECT-TYPE SYNTAX Integer32(0|1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "The integer value used to identify the port's VLAN identifier associated with the remote system. if the remote system either does not know the PVID or does not support port-based VLAN operation, the value of lldpXdot1RemPortVlanId should be zero." REFERENCE "IEEE 802.1AB-2005 F.2.1" ::= { lldpXdot1RemEntry 1 } lldpXdot1RemProtoVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1RemProtoVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per Port and Protocol VLAN information about the remote system, received on the given port." ::= { lldpXdot1RemoteData 2 } lldpXdot1RemProtoVlanEntry OBJECT-TYPE SYNTAX LldpXdot1RemProtoVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Port and protocol VLAN name Information about a particular port component. There may be multiple protocol VLANs, identified by a particular lldpXdot1RemProtoVlanId, configured on the remote system." INDEX { lldpXdot1RemProtoVlanId } ::= { lldpXdot1RemProtoVlanTable 1 } LldpXdot1RemProtoVlanEntry ::= SEQUENCE { lldpXdot1RemProtoVlanId Integer32, lldpXdot1RemProtoVlanSupported TruthValue, lldpXdot1RemProtoVlanEnabled TruthValue } lldpXdot1RemProtoVlanId OBJECT-TYPE SYNTAX Integer32(0|1..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The integer value used to identify the port and protocol VLANs associated with the given port associated with the remote system. If port and protocol VLANs are not supported on the given port associated with the remote system, or if the port is not enabled with any port and protocol VLAN, the value of lldpXdot1RemProtoVlanId should be zero." REFERENCE "IEEE 802.1AB-2005 F.3.2" ::= { lldpXdot1RemProtoVlanEntry 1 } lldpXdot1RemProtoVlanSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether the given port (associated with the remote system) is capable of supporting port and protocol VLANs." REFERENCE "IEEE 802.1AB-2005 F.3.1" ::= { lldpXdot1RemProtoVlanEntry 2 } lldpXdot1RemProtoVlanEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the remote system." REFERENCE "IEEE 802.1AB-2005 F.3.1" ::= { lldpXdot1RemProtoVlanEntry 3 } -- -- lldpXdot1RemVlanNameTable : VLAN name information of the remote -- systems -- lldpXdot1RemVlanNameTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1RemVlanNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per IEEE 802.1Q VLAN name information about the remote system, received on the given port." REFERENCE "IEEE 802.1AB-2005 F.4" ::= { lldpXdot1RemoteData 3 } lldpXdot1RemVlanNameEntry OBJECT-TYPE SYNTAX LldpXdot1RemVlanNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1RemVlanId, received on the given port." INDEX { lldpXdot1RemVlanId } ::= { lldpXdot1RemVlanNameTable 1 } LldpXdot1RemVlanNameEntry ::= SEQUENCE { lldpXdot1RemVlanId VlanId, lldpXdot1RemVlanName SnmpAdminString } lldpXdot1RemVlanId OBJECT-TYPE SYNTAX VlanId MAX-ACCESS not-accessible STATUS current DESCRIPTION "The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port of the remote system is compatible." REFERENCE "IEEE 802.1AB-2005 F.4.2" ::= { lldpXdot1RemVlanNameEntry 1 } lldpXdot1RemVlanName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The string value used to identify VLAN name identified by the VLAN Id associated with the remote system." REFERENCE "IEEE 802.1AB-2005 F.4.4" ::= { lldpXdot1RemVlanNameEntry 2 } -- -- lldpXdot1RemProtocolTable : Protocol information of the remote systems -- lldpXdot1RemProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpXdot1RemProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one or more rows per protocol information about the remote system, received on the given port." ::= { lldpXdot1RemoteData 4 } lldpXdot1RemProtocolEntry OBJECT-TYPE SYNTAX LldpXdot1RemProtocolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Protocol information about a particular port component. There may be multiple protocols, identified by a particular lldpXdot1ProtocolIndex, received on the given port." INDEX { lldpXdot1RemProtocolIndex } ::= { lldpXdot1RemProtocolTable 1 } LldpXdot1RemProtocolEntry ::= SEQUENCE { lldpXdot1RemProtocolIndex Integer32, lldpXdot1RemProtocolId OCTET STRING } lldpXdot1RemProtocolIndex OBJECT-TYPE SYNTAX Integer32(1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity." ::= { lldpXdot1RemProtocolEntry 1 } lldpXdot1RemProtocolId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The octet string value used to identify the protocols associated with the given port of remote system." REFERENCE "IEEE 802.1AB-2005 F.5.3" ::= { lldpXdot1RemProtocolEntry 2 } -- --------------------------------------------------------------------- -- Green Function -- --------------------------------------------------------------------- dlinkGreenLEDShutoff OBJECT IDENTIFIER ::= { companyGreenSetting 1 } dlinkGreenPortShutoff OBJECT IDENTIFIER ::= { companyGreenSetting 2 } dlinkGreenSystemHibernation OBJECT IDENTIFIER ::= { companyGreenSetting 4 } -- --------------------------------------------------------------------- -- Green Disable LED -- --------------------------------------------------------------------- dlinkGreenLEDShutoffPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Provides control to disable LED port." ::= { dlinkGreenLEDShutoff 1 } dlinkGreenLEDShutoffState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Green disable LED function. Default is disabled." DEFVAL { disabled } ::= { dlinkGreenLEDShutoff 2 } dlinkGreenLEDShutoffTimeProfile1 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time profile name associated with the Schedule entry (e.g., `abc, bbb')." ::= { dlinkGreenLEDShutoff 3} dlinkGreenLEDShutoffTimeProfile2 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time profile name associated with the Schedule entry (e.g., `abc, bbb')." ::= { dlinkGreenLEDShutoff 4} -- --------------------------------------------------------------------- -- Green Disable Port -- --------------------------------------------------------------------- dlinkGreenPortShutoffPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Provides control to disable LED port." ::= { dlinkGreenPortShutoff 1 } dlinkGreenPortShutoffState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Green disable LED function. Default is disabled." DEFVAL { disabled } ::= { dlinkGreenPortShutoff 2 } dlinkGreenPortShutoffTimeProfile1 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time profile name associated with the Schedule entry (e.g., `abc, bbb')." ::= { dlinkGreenPortShutoff 3} dlinkGreenPortShutoffTimeProfile2 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time profile name associated with the Schedule entry (e.g., `abc, bbb')." ::= { dlinkGreenPortShutoff 4} -- --------------------------------------------------------------------- -- Green System Hibernation mode -- --------------------------------------------------------------------- dlinkGreenSystemHibernationState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Green disable LED function. Default is disabled." DEFVAL { disabled } ::= { dlinkGreenSystemHibernation 1 } dlinkGreenSystemHibernationTimeProfile1 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time profile name associated with the Schedule entry (e.g., `abc, bbb')." ::= { dlinkGreenSystemHibernation 2} dlinkGreenSystemHibernationTimeProfile2 OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time profile name associated with the Schedule entry (e.g., `abc, bbb')." ::= { dlinkGreenSystemHibernation 3} dlinkPowerSavLinkStatusDetectState OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Power Saving Link Status Detection. Default is disabled." DEFVAL { disabled } ::= { companyGreenSetting 6 } -- ---------------------------------------------------------- -- The companySecurity Groups -- ---------------------------------------------------------- securityDhcpServerScreen OBJECT IDENTIFIER ::= { companySecurity 7 } -- dhcp Server Screen Group --------------------------------------------- -- dhcpServerScreenEnablePortlist OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "To enable or disable DHCP Server Screening port list." ::= { securityDhcpServerScreen 1 } dhcpServerScreenEnableVlanlist OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "To enable or disable DHCP Server Screening vlan list." ::= { securityDhcpServerScreen 2 } dhcpServerScreenLogSuppressDuration OBJECT-TYPE SYNTAX INTEGER { one_min (1), five_min (5), thirty_min (30) } MAX-ACCESS read-write STATUS current DESCRIPTION "DSS Trap Log Suppress Duration." ::= { securityDhcpServerScreen 3 } -- filterDHCPServer Table filterDHCPServerTable OBJECT-TYPE SYNTAX SEQUENCE OF FilterDHCPServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control filter DHCP Server for the entire switch or for each interface in the switch." ::= { securityDhcpServerScreen 4 } filterDHCPServerEntry OBJECT-TYPE SYNTAX FilterDHCPServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system." INDEX { filterDHCPServerIpAddr, filterDHCPServerClientMacAddr } ::= { filterDHCPServerTable 1 } FilterDHCPServerEntry ::= SEQUENCE { filterDHCPServerIpAddr IpAddress, filterDHCPServerClientMacAddr MacAddress, filterDHCPServerPortList PortList, filterDHCPServerVlanList OCTET STRING, filterDHCPServerRowStatus RowStatus } filterDHCPServerIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'." ::= { filterDHCPServerEntry 1 } filterDHCPServerClientMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Ethernet Mac Address." DEFVAL { '000102030405'h } ::= { filterDHCPServerEntry 2 } filterDHCPServerPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports." ::= { filterDHCPServerEntry 3 } filterDHCPServerVlanList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports." ::= { filterDHCPServerEntry 4 } filterDHCPServerRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { filterDHCPServerEntry 99 } securityTrafficSeg OBJECT IDENTIFIER ::= { companySecurity 9} -- -- Port Map Table -- trafficSegTable OBJECT-TYPE SYNTAX SEQUENCE OF TrafficSegEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel" ::= { securityTrafficSeg 1 } trafficSegEntry OBJECT-TYPE SYNTAX TrafficSegEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each created port-channel port" INDEX { trafficSegIfIndex } ::= { trafficSegTable 1 } TrafficSegEntry ::= SEQUENCE { trafficSegIfIndex InterfaceIndex, trafficSegMemberList PortList } trafficSegIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex of the port-channel(Aggregator's interface index). " ::= { trafficSegEntry 1 } trafficSegMemberList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "Port list of port channel." ::= { trafficSegEntry 2 } -- ---------------------------------------------------------- -- The companySecurity Groups -- ---------------------------------------------------------- securityAAC OBJECT IDENTIFIER ::= { companySecurity 11 } -- ------------------------------------------------------------- -- Authentication Policy and Parameter Settings -- ------------------------------------------------------------- aacAuthenAdminState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the Access Authentication is enable or disable." ::= { securityAAC 1} aacAuthParamResponseTimeout OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Timeout in second for login authentication response." ::= { securityAAC 2 } aacAuthParamAttempt OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The amount for login authentication, if login failure exceed, connection or access would be locked." ::= { securityAAC 3 } -- ------------------------------------------------------------- -- Application Authentication Settings -- ------------------------------------------------------------- aacAPAuthMethodGroup OBJECT IDENTIFIER ::= { securityAAC 4 } aacAPLoginMethod OBJECT IDENTIFIER ::= { aacAPAuthMethodGroup 1 } aacAPEnableMethod OBJECT IDENTIFIER ::= { aacAPAuthMethodGroup 2 } aacAPConsoleLoginMethod OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the way which has to execute authentication while login the system and the method for authentication.Access system via local console" ::= { aacAPLoginMethod 1 } aacAPTelnetLoginMethod OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet." ::= { aacAPLoginMethod 2 } aacAPSSHLoginMethod OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the way which has to execute authentication while login the system and the method for authentication.Access system via SSH." ::= { aacAPLoginMethod 3 } aacAPHttpLoginMethod OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP." ::= { aacAPLoginMethod 4 } aacAPConsoleEnableMethod OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the way which has to execute authentication while login the system and the method for authentication.Access system via local console." ::= { aacAPEnableMethod 1 } aacAPTelnetEnableMethod OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet." ::= { aacAPEnableMethod 2 } aacAPSSHEnableMethod OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the way which has to execute authentication while login the system and the method for authentication.Access system via SSH." ::= { aacAPEnableMethod 3 } aacAPHttpEnableMethod OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP." ::= { aacAPEnableMethod 4 } -- ------------------------------------------------------------- -- Authentication Server Group setting -- ------------------------------------------------------------- aacServerGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF AacServerGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains informations about server group." ::= { securityAAC 5 } aacServerGroupEntry OBJECT-TYPE SYNTAX AacServerGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the group including servers." INDEX { aacServerGroupIndex } ::= { aacServerGroupTable 1 } AacServerGroupEntry ::= SEQUENCE { aacServerGroupIndex INTEGER, aacServerGroupName OCTET STRING, aacServersInGroup BITS, aacServerGroupRowStatus RowStatus } aacServerGroupIndex OBJECT-TYPE SYNTAX INTEGER (2..9) MAX-ACCESS read-only STATUS current DESCRIPTION "A value that uniquely identifies this SwAACServerGroupEntry ." ::= { aacServerGroupEntry 1 } aacServerGroupName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "A human-readable text string of the method group. The name is writable only if Group is new created, which the value of aacServerGroupRowStatus is 'notReady'." ::= { aacServerGroupEntry 2 } aacServersInGroup OBJECT-TYPE SYNTAX BITS { id1(0), id2(1), id3(2), id4(3), id5(4), id6(5), id7(6), id8(7), id9(8), id10(9), id11(10), id12(11), id13(12), id14(13), id15(14), id16(15) } MAX-ACCESS read-write STATUS current DESCRIPTION "The list of servers in the group, each bit indicates a specified server ID. The server must be created before including it." ::= { aacServerGroupEntry 3 } aacServerGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aacServerGroupEntry 4 } -- ------------------------------------------------------------- -- IPv4 -- Authentication Server host setting -- ------------------------------------------------------------- iPv4aacServerInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF IPv4AacServerInfoEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A table that contains information about severs." ::= { securityAAC 6 } iPv4aacServerInfoEntry OBJECT-TYPE SYNTAX IPv4AacServerInfoEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A list of the information of server ." INDEX { iPv4aacServerIndex } ::= { iPv4aacServerInfoTable 1 } IPv4AacServerInfoEntry ::= SEQUENCE { iPv4aacServerIndex INTEGER, iPv4aacServerIPAddr IpAddress, iPv4aacServerAuthProtocol INTEGER, iPv4aacServerAuthPort INTEGER, iPv4aacServerAuthKey OCTET STRING, iPv4aacServerTimeout INTEGER, iPv4aacServerRetryCount INTEGER, iPv4aacServerRowStatus RowStatus } iPv4aacServerIndex OBJECT-TYPE SYNTAX INTEGER (1..16) MAX-ACCESS read-only STATUS obsolete DESCRIPTION "A value that uniquely identifies this SwAACServerGroupEntry." ::= { iPv4aacServerInfoEntry 1 } iPv4aacServerIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The IP address of Server" ::= { iPv4aacServerInfoEntry 2 } iPv4aacServerAuthProtocol OBJECT-TYPE SYNTAX INTEGER{ tacacsPlus(1), radius(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The authentication protocol provided by the Server." ::= { iPv4aacServerInfoEntry 3 } iPv4aacServerAuthPort OBJECT-TYPE SYNTAX INTEGER(1..65535) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The TCP/IP port ." ::= { iPv4aacServerInfoEntry 4 } iPv4aacServerAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..254)) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The key used while authentication process." ::= { iPv4aacServerInfoEntry 5 } iPv4aacServerTimeout OBJECT-TYPE SYNTAX INTEGER(1..255) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Server response timeout ." ::= { iPv4aacServerInfoEntry 6 } iPv4aacServerRetryCount OBJECT-TYPE SYNTAX INTEGER(1..255) MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Client retry count . (-1: No retry mechanism)" ::= { iPv4aacServerInfoEntry 7 } iPv4aacServerRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS obsolete DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { iPv4aacServerInfoEntry 8 } -- ------------------------------------------------------------- -- IPv6 -- Authentication Server host setting -- ------------------------------------------------------------- aacServerInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF AacServerInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about severs." ::= { securityAAC 7 } aacServerInfoEntry OBJECT-TYPE SYNTAX AacServerInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the information of server ." INDEX { aacServerIndex } ::= { aacServerInfoTable 1 } AacServerInfoEntry ::= SEQUENCE { aacServerIndex INTEGER, aacServerIPType INTEGER, aacServerIPAddr Ipv6Address, aacServerInterfaceName OCTET STRING, aacServerAuthProtocol INTEGER, aacServerAuthPort INTEGER, aacServerAuthKey OCTET STRING, aacServerTimeout INTEGER, aacServerRetryCount INTEGER, aacServerAccountingPort INTEGER, aacServerRowStatus RowStatus } aacServerIndex OBJECT-TYPE SYNTAX INTEGER (1..16) MAX-ACCESS read-only STATUS current DESCRIPTION "A value that uniquely identifies this SwAACServerGroupEntry." ::= { aacServerInfoEntry 1 } aacServerIPType OBJECT-TYPE SYNTAX INTEGER (1..2) MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the AAC server IP type referred to in this table entry. (IPv4=1, IPv6=2)" DEFVAL { 1 } ::= { aacServerInfoEntry 2 } aacServerIPAddr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of Server" ::= { aacServerInfoEntry 3 } aacServerInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the interface name when the aacServerIPAddr is linklocal address." ::= { aacServerInfoEntry 4 } aacServerAuthProtocol OBJECT-TYPE SYNTAX INTEGER{ tacacsPlus(1), radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The authentication protocol provided by the Server." ::= { aacServerInfoEntry 5 } aacServerAuthPort OBJECT-TYPE SYNTAX INTEGER(1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP/IP port ." ::= { aacServerInfoEntry 6 } aacServerAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..254)) MAX-ACCESS read-write STATUS current DESCRIPTION "The key used while authentication process." ::= { aacServerInfoEntry 7 } aacServerTimeout OBJECT-TYPE SYNTAX INTEGER(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Server response timeout ." ::= { aacServerInfoEntry 8 } aacServerRetryCount OBJECT-TYPE SYNTAX INTEGER(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Client retry count . (-1: No retry mechanism)" ::= { aacServerInfoEntry 9 } aacServerAccountingPort OBJECT-TYPE SYNTAX INTEGER(1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The accounting port ." ::= { aacServerInfoEntry 10 } aacServerRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aacServerInfoEntry 99 } -- ------------------------------------------------------------- -- Login Method list table -- ------------------------------------------------------------- aacLoginMethodListTable OBJECT-TYPE SYNTAX SEQUENCE OF AacLoginMethodListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about Login authentication method lists." ::= { securityAAC 8 } aacLoginMethodListEntry OBJECT-TYPE SYNTAX AacLoginMethodListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the Authentication methods." INDEX { aacLoginMethodListIndex } ::= { aacLoginMethodListTable 1 } AacLoginMethodListEntry ::= SEQUENCE { aacLoginMethodListIndex INTEGER, aacLoginMethodListName OCTET STRING, aacLoginMethod1 INTEGER, aacLoginMethod2 INTEGER, aacLoginMethod3 INTEGER, aacLoginMethod4 INTEGER, aacLoginMethodListRowStatus RowStatus } aacLoginMethodListIndex OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-only STATUS current DESCRIPTION "A value that identifies this method list." ::= { aacLoginMethodListEntry 1 } aacLoginMethodListName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "A human-readable text string of the method list." ::= { aacLoginMethodListEntry 2 } aacLoginMethod1 OBJECT-TYPE SYNTAX INTEGER { none(-1), local(0) ,tacacsPlus(1) ,radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex." ::= { aacLoginMethodListEntry 3 } aacLoginMethod2 OBJECT-TYPE SYNTAX INTEGER { none(-1), local(0) ,tacacsPlus(1) ,radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex." ::= { aacLoginMethodListEntry 4 } aacLoginMethod3 OBJECT-TYPE SYNTAX INTEGER { none(-1), local(0) ,tacacsPlus(1) ,radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex." ::= { aacLoginMethodListEntry 5 } aacLoginMethod4 OBJECT-TYPE SYNTAX INTEGER { none(-1), local(0) ,tacacsPlus(1) ,radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex." ::= { aacLoginMethodListEntry 6 } aacLoginMethodListRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aacLoginMethodListEntry 7 } -- ------------------------------------------------------------- -- Enable Method table -- ------------------------------------------------------------- aacEnableMethodListTable OBJECT-TYPE SYNTAX SEQUENCE OF AacEnableMethodListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about Enable authentication method lists." ::= { securityAAC 9 } aacEnableMethodListEntry OBJECT-TYPE SYNTAX AacEnableMethodListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the Authentication methods." INDEX { aacEnableMethodListIndex } ::= { aacEnableMethodListTable 1 } AacEnableMethodListEntry ::= SEQUENCE { aacEnableMethodListIndex INTEGER, aacEnableMethodListName OCTET STRING, aacEnableMethod1 INTEGER, aacEnableMethod2 INTEGER, aacEnableMethod3 INTEGER, aacEnableMethod4 INTEGER, aacEnableMethodListRowStatus RowStatus } aacEnableMethodListIndex OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-only STATUS current DESCRIPTION "A value that identifies this method list." ::= { aacEnableMethodListEntry 1 } aacEnableMethodListName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "A human-readable text string of the method list." ::= { aacEnableMethodListEntry 2 } aacEnableMethod1 OBJECT-TYPE SYNTAX INTEGER { none(-1), local(0) ,tacacsPlus(1) ,radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex." ::= { aacEnableMethodListEntry 3 } aacEnableMethod2 OBJECT-TYPE SYNTAX INTEGER { none(-1), local(0) ,tacacsPlus(1) ,radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex." ::= { aacEnableMethodListEntry 4 } aacEnableMethod3 OBJECT-TYPE SYNTAX INTEGER { none(-1), local(0) ,tacacsPlus(1) ,radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex." ::= { aacEnableMethodListEntry 5 } aacEnableMethod4 OBJECT-TYPE SYNTAX INTEGER { none(-1), local(0) ,tacacsPlus(1) ,radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex." ::= { aacEnableMethodListEntry 6 } aacEnableMethodListRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aacEnableMethodListEntry 7 } -- ------------------------------------------------------------- -- Local Enable Password -- ------------------------------------------------------------- aacLocalEnablePassword OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set Local Enable Password." ::= { securityAAC 10 } -- ------------------------------------------------------------- -- Accounting Method list table -- ------------------------------------------------------------- aacAccountingMethodListTable OBJECT-TYPE SYNTAX SEQUENCE OF AacAccountingMethodListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about Accounting authentication method lists." ::= { securityAAC 11 } aacAccountingMethodListEntry OBJECT-TYPE SYNTAX AacAccountingMethodListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the Authentication methods." INDEX { aacAccountingMethodListIndex } ::= { aacAccountingMethodListTable 1 } AacAccountingMethodListEntry ::= SEQUENCE { aacAccountingMethodListIndex INTEGER, aacAccountingMethodListName OCTET STRING, aacAccountingMethod1 INTEGER, aacAccountingMethod2 INTEGER, aacAccountingMethod3 INTEGER, aacAccountingMethod4 INTEGER, aacAccountingMethodListRowStatus RowStatus } aacAccountingMethodListIndex OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-only STATUS current DESCRIPTION "A value that identifies this method list." ::= { aacAccountingMethodListEntry 1 } aacAccountingMethodListName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "A human-readable text string of the method list." ::= { aacAccountingMethodListEntry 2 } aacAccountingMethod1 OBJECT-TYPE SYNTAX INTEGER { none(-1), local(0) ,tacacsPlus(1) ,radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Accounting method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex." ::= { aacAccountingMethodListEntry 3 } aacAccountingMethod2 OBJECT-TYPE SYNTAX INTEGER { none(-1), local(0) ,tacacsPlus(1) ,radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Accounting method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex." ::= { aacAccountingMethodListEntry 4 } aacAccountingMethod3 OBJECT-TYPE SYNTAX INTEGER { none(-1), local(0) ,tacacsPlus(1) ,radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Accounting method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex." ::= { aacAccountingMethodListEntry 5 } aacAccountingMethod4 OBJECT-TYPE SYNTAX INTEGER { none(-1), local(0) ,tacacsPlus(1) ,radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Accounting method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex." ::= { aacAccountingMethodListEntry 6 } aacAccountingMethodListRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'." ::= { aacAccountingMethodListEntry 7 } -- ------------------------------------------------------------- -- Accounting Service Index -- ------------------------------------------------------------- aacAccountingServiceIndex OBJECT IDENTIFIER ::= { securityAAC 12 } aacAccountingServiceNetwork OBJECT-TYPE SYNTAX INTEGER { radius_only (0), default_method_list (1), method_list_name (2), disabled (-1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates aac Accounting Service Network is radius_only, default_method_list, method_list_name and disable about Accounting Service Network." DEFVAL { -1 } ::= { aacAccountingServiceIndex 1 } aacAccountingServiceShell OBJECT-TYPE SYNTAX INTEGER { radius_only (0), default_method_list (1), method_list_name (2), disabled (-1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates aac Accounting Service Shell is radius_only, default_method_list, method_list_name and disable about Accounting Service Network." DEFVAL { -1 } ::= { aacAccountingServiceIndex 2 } aacAccountingServiceSystem OBJECT-TYPE SYNTAX INTEGER { radius_only (0), default_method_list (1), method_list_name (2), disabled (-1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates aac Accounting System Shell is radius_only, default_method_list, method_list_name and disable about Accounting Service Network." DEFVAL { -1 } ::= { aacAccountingServiceIndex 3 } -- ------------------------------------------------------------- -- Accounting Service Command -- ------------------------------------------------------------- aacAccountingServiceCommand OBJECT IDENTIFIER ::= { securityAAC 13 } aacAccountingServiceCommandAdministrator OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates which method list Accounting Admin Command Service uses. If the value is -1, it means disabled." DEFVAL { -1 } ::= { aacAccountingServiceCommand 1 } aacAccountingServiceCommandOperator OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates which method list Accounting Operator Command Service uses. If the value is -1, it means disabled." DEFVAL { -1 } ::= { aacAccountingServiceCommand 2 } aacAccountingServiceCommandPoweruser OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates which method list Accounting PowerUser Command Service uses. If the value is -1, it means disabled." DEFVAL { -1 } ::= { aacAccountingServiceCommand 3 } aacAccountingServiceCommandUser OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates which method list Accounting User Command Service uses. If the value is -1, it means disabled." DEFVAL { -1 } ::= { aacAccountingServiceCommand 4 } -- ------------------------------------------------------------- -- Server Password Encryption -- ------------------------------------------------------------- aacServerPasswordEncryption OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure server password encryption status." ::= { securityAAC 14 } -- ---------------------------------------------------------------- -- The STATIC ARP group -- ---------------------------------------------------------------- staticARPTable OBJECT-TYPE SYNTAX SEQUENCE OF StaticARPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the Static MACs" ::= { companyStaticARP 2 } staticARPEntry OBJECT-TYPE SYNTAX StaticARPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Static MAC entry containing the mac and forwarding port." INDEX { staticARPIP, staticARPMac} ::= { staticARPTable 1 } StaticARPEntry ::= SEQUENCE { staticARPIP IpAddress, staticARPMac MacAddress, staticARPRowStatus RowStatus } staticARPIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the static ARP IP." ::= { staticARPEntry 2 } staticARPMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the static ARP entry." ::= { staticARPEntry 3 } staticARPRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of an entry in the Static ARP Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static ARP." ::= { staticARPEntry 5 } sysGratuitousARPGlobalSettings OBJECT IDENTIFIER ::= { companyGratuitousARP 1 } sysGratuitousARPSettings OBJECT IDENTIFIER ::= { companyGratuitousARP 2 } -- ---------------------------------------------------------------- -- The sysGratuitousARPGlobalSettings group -- ---------------------------------------------------------------- sysGratuitousARPIPIfStatusUp OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates Send On IP Interface Status Up is enabled or disabled." DEFVAL { disable } ::= { sysGratuitousARPGlobalSettings 1 } sysGratuitousARPDuplicateIPDetected OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates Send On Duplicate IP Detected is enabled or disabled." DEFVAL { disable } ::= { sysGratuitousARPGlobalSettings 2 } sysGratuitousARPLearning OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates Gratuitous ARP Learning is enabled or disabled." DEFVAL { disable } ::= { sysGratuitousARPGlobalSettings 3 } -- ---------------------------------------------------------------- -- The sysGratuitousARPSettings group -- ---------------------------------------------------------------- sysGratuitousARPTable OBJECT-TYPE SYNTAX SEQUENCE OF SysGratuitousARPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Set/Add Gratuitous ARP interface name and interval time." ::= { sysGratuitousARPSettings 1 } sysGratuitousARPEntry OBJECT-TYPE SYNTAX SysGratuitousARPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of gratuitous ARP!" INDEX { sysGratuitousARPIFName } ::= { sysGratuitousARPTable 1 } SysGratuitousARPEntry ::= SEQUENCE { sysGratuitousARPIFName OCTET STRING, sysGratuitousARPInterval Integer32 } sysGratuitousARPIFName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Interface name." ::= { sysGratuitousARPEntry 1 } sysGratuitousARPInterval OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Gratuitous ARP interval time for each interface." DEFVAL { 0 } ::= { sysGratuitousARPEntry 2 } -- --------------------------------------------------------------------- -- IP Multi-Interface Function -- --------------------------------------------------------------------- ipv4multiIFInfo OBJECT IDENTIFIER ::= { companyMultiIPInterface 1 } ipv4mulIfMainTable OBJECT-TYPE SYNTAX SEQUENCE OF Ipv4MulIfMainEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A list of interface entries." ::= { ipv4multiIFInfo 1 } ipv4mulIfMainEntry OBJECT-TYPE SYNTAX Ipv4MulIfMainEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "An entry containing management information applicable to a particular interface." INDEX { ipv4mulifMainIndex, ipv4mulifVLANID } ::= { ipv4mulIfMainTable 1 } Ipv4MulIfMainEntry ::= SEQUENCE { ipv4mulifMainIndex InterfaceIndex, ipv4mulifVLANID INTEGER, ipv4mulifName OCTET STRING, ipv4mulifVLANname OCTET STRING, ipv4mulifIpAddr IpAddress, ipv4mulifIpSubnetMask IpAddress, ipv4mulifMainAdminStatus INTEGER, ipv4mulifMainOperStatus INTEGER, ipv4mulifMainRowStatus RowStatus } ipv4mulifMainIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The index of this interface." ::= { ipv4mulIfMainEntry 1 } ipv4mulifVLANID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The ID of VLAN that you want this interface to be in. It must be a exist vlan id." ::= { ipv4mulIfMainEntry 2 } ipv4mulifName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The Description for the interface." ::= { ipv4mulIfMainEntry 3 } ipv4mulifVLANname OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The vlan name for the interface." ::= { ipv4mulIfMainEntry 4 } ipv4mulifIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The ip address of this interface." DEFVAL { '00000000'H } ::= { ipv4mulIfMainEntry 6 } ipv4mulifIpSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The subnet mask of this interface." ::= { ipv4mulIfMainEntry 7 } ipv4mulifMainAdminStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS obsolete DESCRIPTION "The desired state of the interface." DEFVAL { disable } ::= { ipv4mulIfMainEntry 8 } ipv4mulifMainOperStatus OBJECT-TYPE SYNTAX INTEGER { linkup(1), -- ready to pass packets linkdown(2) } MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The current operational state of the interface." ::= { ipv4mulIfMainEntry 9 } ipv4mulifMainRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS obsolete DESCRIPTION "The status of an entry in the Multi Interface Table. Only a subset of the rowstatus variables (active, createAndWait, destroy) are available." ::= { ipv4mulIfMainEntry 10 } -- --------------------------------------------------------------------- -- IPv6 Multi-Interface Function -- --------------------------------------------------------------------- multiIFSupportV4V6Info OBJECT IDENTIFIER ::= { companyMultiIPInterface 2 } -- --------------------------------------------------------------------- -- --------------------------------------------------------------------- mulIfSupportV4V6MainTable OBJECT-TYPE SYNTAX SEQUENCE OF MulIfSupportV4V6MainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of interface entries." ::= { multiIFSupportV4V6Info 1 } mulIfSupportV4V6MainEntry OBJECT-TYPE SYNTAX MulIfSupportV4V6MainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing management information applicable to a particular interface." INDEX { mulifMainIndex, mulifVLANID } ::= { mulIfSupportV4V6MainTable 1 } MulIfSupportV4V6MainEntry ::= SEQUENCE { mulifMainIndex InterfaceIndex, mulifVLANID INTEGER, mulifName OCTET STRING, mulifVLANname OCTET STRING, mulifIpAddr IpAddress, mulifIpSubnetMask IpAddress, mulifMainAdminStatus INTEGER, mulifMainOperStatus INTEGER, mulifv6GlobalStatus INTEGER, -- Support IPv6 or not. mulifv6DHCPStatus INTEGER, -- Support DHCPv6 or not. mulifv6AutolinkloStatus INTEGER, -- Automatic Link local Address Status. mulifv6NSRetransmitTime INTEGER, -- NS Retransmit Time Settings. mulifMainRowStatus RowStatus -- Entries Row status. } mulifMainIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of this interface." ::= { mulIfSupportV4V6MainEntry 1 } mulifVLANID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The ID of VLAN that you want this interface to be in. It must be a exist vlan id." ::= { mulIfSupportV4V6MainEntry 2 } mulifName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The Description for the interface." ::= { mulIfSupportV4V6MainEntry 3 } mulifVLANname OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan name for the interface." ::= { mulIfSupportV4V6MainEntry 4 } mulifIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The ip address of this interface." DEFVAL { '00000000'H } ::= { mulIfSupportV4V6MainEntry 5 } mulifIpSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The subnet mask of this interface." ::= { mulIfSupportV4V6MainEntry 6 } mulifMainAdminStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The desired state of the interface." DEFVAL { disable } ::= { mulIfSupportV4V6MainEntry 7 } mulifMainOperStatus OBJECT-TYPE SYNTAX INTEGER { linkup(1), -- ready to pass packets linkdown(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational state of the interface." ::= { mulIfSupportV4V6MainEntry 8 } mulifv6GlobalStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The ID of VLAN that you want this interface to be in. It must be a exist vlan id." ::= { mulIfSupportV4V6MainEntry 9 } mulifv6DHCPStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of DHCPv6 that you want this interface to be in. It must be a exist vlan id." ::= { mulIfSupportV4V6MainEntry 10 } mulifv6AutolinkloStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The global state of link local that you want this interface to be in. It must be a exist vlan id." ::= { mulIfSupportV4V6MainEntry 11 } mulifv6NSRetransmitTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "The NS's retransmit time that you want this interface to be in. It must be a exist vlan id." ::= { mulIfSupportV4V6MainEntry 12 } mulifMainRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of an entry in the Multi Interface Table. Only a subset of the rowstatus variables (active, createAndWait, destroy) are available." ::= { mulIfSupportV4V6MainEntry 13 } -- --------------------------------------------------------------------- -- --------------------------------------------------------------------- mulIfV6AddressTable OBJECT-TYPE SYNTAX SEQUENCE OF MulIfV6AddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of interface entries." ::= { multiIFSupportV4V6Info 2 } mulIfV6AddressEntry OBJECT-TYPE SYNTAX MulIfV6AddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing management information applicable to a particular interface." INDEX { mulifV6AddressMainIndex, mulifV6AddressIpAddr, mulifV6AddressIpPrefix } ::= { mulIfV6AddressTable 1 } MulIfV6AddressEntry ::= SEQUENCE { mulifV6AddressMainIndex InterfaceIndex, mulifV6AddressIpAddr Ipv6Address, -- IPv6 Address. mulifV6AddressIpPrefix INTEGER, -- IPv6 Address Prefix. mulifV6AddressIpType INTEGER, -- IP type (Link-local, Global, anycast). mulifV6AddressRowStatus RowStatus -- IPv6 Address entries row status. } mulifV6AddressMainIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The index of this IPv6 entry." ::= { mulIfV6AddressEntry 1 } mulifV6AddressIpAddr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The ip address of this IPv6 entry." DEFVAL { '00000000'H } ::= { mulIfV6AddressEntry 2 } mulifV6AddressIpPrefix OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The ip prefix of this IPv6 entry." ::= { mulIfV6AddressEntry 3 } mulifV6AddressIpType OBJECT-TYPE SYNTAX INTEGER { unicast(1), anycast(2), linklocal(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The ip type of this IPv6 entry." ::= { mulIfV6AddressEntry 4 } mulifV6AddressRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of an entry in the Multi Interface Table. Only a subset of the rowstatus variables (active, createAndWait, destroy) are available." ::= { mulIfV6AddressEntry 5 } -- start DLINK_AGENT_BACIC_INFO agentCPUutilization OBJECT IDENTIFIER ::= { companyAgentBasicInfo 1 } agentMEMutilization OBJECT IDENTIFIER ::= { companyAgentBasicInfo 2 } -- ---------------------------------------------------------------- -- The agentCPUutilization group -- ---------------------------------------------------------------- agentCPUutilizationIn5sec OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The time scale is set at 5 second intervals. The value will be between 0% (idle) and 100% (very busy)." ::= { agentCPUutilization 1 } agentCPUutilizationIn1min OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The time scale is set at 1 minute intervals. The value will be between 0% (idle) and 100% (very busy)." ::= { agentCPUutilization 2 } agentCPUutilizationIn5min OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The time scale is set at 5 minute intervals. The value will be between 0% (idle) and 100% (very busy)." ::= { agentCPUutilization 3 } -- ---------------------------------------------------------------- -- The agentMEMutilization group -- ---------------------------------------------------------------- agentMEMutilizationIn5sec OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The time scale is set at 5 second intervals. The value will be between 0% (idle) and 100% (very busy)." ::= { agentMEMutilization 1 } agentMEMutilizationIn1min OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The time scale is set at 1 minute intervals. The value will be between 0% (idle) and 100% (very busy)." ::= { agentMEMutilization 2 } agentMEMutilizationIn5min OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The time scale is set at 5 minute intervals. The value will be between 0% (idle) and 100% (very busy)." ::= { agentMEMutilization 3 } -- end DLINK_AGENT_BACIC_INFO -- ---------------------------------------------------------- -- The companyL2PT Groups -- ---------------------------------------------------------- -- L2PT Group --------------------------------------------- -- -- ----------------------------------------------------------------------------- -- swL2PTState -- ----------------------------------------------------------------------------- l2PTState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the global state of Layer 2 protocol tunneling." ::= { companyL2PT 1 } -- ----------------------------------------------------------------------------- -- L2PTPortTable -- ----------------------------------------------------------------------------- l2PTPortTable OBJECT-TYPE SYNTAX SEQUENCE OF L2PTEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that cont ains the cable situation for each port." ::= { companyL2PT 2 } l2PTEntry OBJECT-TYPE SYNTAX L2PTEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of cable situations for each port on the device." INDEX { l2PTPortIndex } ::= { l2PTPortTable 1 } L2PTEntry ::= SEQUENCE { l2PTPortIndex INTEGER, l2PTPortType INTEGER, l2PTProtocol BITS } l2PTPortIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the port number." ::= { l2PTEntry 1 } l2PTPortType OBJECT-TYPE SYNTAX INTEGER { none(1), uni(2), nni(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the Layer 2 protocol tunneling port type. The 'none' value indicates that the port is normal. Layer 2 protocol tunneling is disabled on this port. The 'uni' value indicates that the port is connected to the customer site. A Layer 2 PDU received on a UNI port can be tunneled to a remote customer site across the provider network. The 'nni' value indicates that the port is connected to the provider network. A Tunneled Layer 2 PDU received on an NNI port will be restored to its original format." DEFVAL { none } ::= { l2PTEntry 2 } l2PTProtocol OBJECT-TYPE SYNTAX BITS { stp(0), gvrp(1), macCC(2), macCD(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the tunneled protocols on this port. This object can only be applied on a UNI port. If the 'stp' BIT is set, the STP BPDU will be tunneled. If the 'gvrp' BIT is set, the GVRP PDU will be tunneled. If the 'mac-01-00-0C-CC-CC-CC' BIT is set, the PDU with the destination MAC address 01-00-0C-CC-CC-CC will be tunneled . If the 'mac-01-00-0C-CC-CC-CD' BIT is set, then the PDU with the destination MAC address 01-00-0C-CC-CC-CD will be tunneled." ::= { l2PTEntry 3 } -- ----------------------------------------------------------------------------- -- L2PTThresholdTable -- ----------------------------------------------------------------------------- l2PTThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF L2PTThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the protocol tunneling threshold of a UNI port." ::= { companyL2PT 3} l2PTThresholdEntry OBJECT-TYPE SYNTAX L2PTThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list with the Layer2 Protocol tunneling threshold." INDEX { l2PTPortIndex, l2PTProtocolIndex } ::= { l2PTThresholdTable 1 } L2PTThresholdEntry ::= SEQUENCE { l2PTProtocolIndex INTEGER, l2PTDropThreshold INTEGER } l2PTProtocolIndex OBJECT-TYPE SYNTAX INTEGER { stp(1), gvrp(2), macCC(3), macCD(4) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the tunneled protocol of the port." ::= { l2PTThresholdEntry 1 } l2PTDropThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the drop threshold for a given protocol on a UNI port. If the arrival rate of a tunneled protocol has reached its threshold, the received PDUs of this protocol will be dropped. The value 0 indicates there is no threshold for the protocol." DEFVAL { 0 } ::= { l2PTThresholdEntry 2 } -- ---------------------------------------------------------- -- The companyCpuProtect Groups -- ---------------------------------------------------------- cpuProtectState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of the cpu protect." ::= { companyCpuProtect 1 } cpuProtectTable OBJECT-TYPE SYNTAX SEQUENCE OF CpuProtectEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that holds the cpu protect settings of the device." ::= { companyCpuProtect 2 } cpuProtectEntry OBJECT-TYPE SYNTAX CpuProtectEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of cpu protect settings of the device." INDEX { cpuProtectType } ::= { cpuProtectTable 1 } CpuProtectEntry ::= SEQUENCE { cpuProtectType INTEGER, cpuProtectPPS INTEGER } cpuProtectType OBJECT-TYPE SYNTAX INTEGER { arp(1), bpdu(2), icmp(3), igmp(4), snmp(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the Cpu protect type." ::= { cpuProtectEntry 1 } cpuProtectPPS OBJECT-TYPE SYNTAX INTEGER (-1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the threshold as packet count per second at which traffic is received on the CPU port. If value set to -1, it means no threshold." ::= { cpuProtectEntry 2 } -- ------------------------------------------------------------------ -- The SMTP Group -- ------------------------------------------------------------------ ipv4smtpState OBJECT-TYPE SYNTAX INTEGER { disabled(0),enabled(1) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "Enable or Disable SMTP function." ::= { companySMTP 1 } ipv4smtpServerAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS obsolete DESCRIPTION "SMTP Server's IP Address" ::= { companySMTP 2 } ipv4smtpServerPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS obsolete DESCRIPTION "SMTP Server's port" ::= { companySMTP 3} ipv4smtpSelfMailAddr OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS obsolete DESCRIPTION "The sender's (DUT) mail address ." ::= { companySMTP 4 } -- ------------------------------------------------------------------ -- smtpRecvMailAddrTable -- ------------------------------------------------------------------ ipv4smtpRecvMailAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF Ipv4SmtpRecvMailAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Receivers' mail address table." ::= { companySMTP 5 } ipv4smtpRecvMailAddrEntry OBJECT-TYPE SYNTAX Ipv4SmtpRecvMailAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Receivers' mail address entry." INDEX { ipv4smtpRecvMailAddrIndex } ::= { ipv4smtpRecvMailAddrTable 1 } Ipv4SmtpRecvMailAddrEntry ::= SEQUENCE { ipv4smtpRecvMailAddrIndex INTEGER, ipv4smtpRecvMailAddr OCTET STRING, ipv4smtpRecvMailAddrStatus RowStatus } ipv4smtpRecvMailAddrIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Receivers' mail address index (1~8)." ::= { ipv4smtpRecvMailAddrEntry 1 } ipv4smtpRecvMailAddr OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Receivers' mail address." ::= { ipv4smtpRecvMailAddrEntry 2 } ipv4smtpRecvMailAddrStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Rowstatus of the receiver's mail address." ::= { ipv4smtpRecvMailAddrEntry 3 } --IPv6 smtp server Group sysSMTPServerGroup OBJECT IDENTIFIER ::= { companySMTP 6 } smtpState OBJECT-TYPE SYNTAX INTEGER { disabled(0),enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or Disable SMTP function." ::= { sysSMTPServerGroup 1 } smtpServerAddr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "SMTP Server's IP Address" ::= { sysSMTPServerGroup 2 } smtpServerAddrType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "SMTP Server's Address type." ::= { sysSMTPServerGroup 3 } smtpServerAddrInterfaceName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the interface name when the smtpServerAddrInterfaceName is linklocal address." ::= { sysSMTPServerGroup 4 } smtpServerPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "SMTP Server's port" ::= { sysSMTPServerGroup 5} smtpSelfMailAddr OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The sender's (DUT) mail address ." ::= { sysSMTPServerGroup 6 } -- ------------------------------------------------------------------ -- smtpRecvMailAddrTable -- ------------------------------------------------------------------ smtpRecvMailAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF SmtpRecvMailAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Receivers' mail address table." ::= { sysSMTPServerGroup 7 } smtpRecvMailAddrEntry OBJECT-TYPE SYNTAX SmtpRecvMailAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Receivers' mail address entry." INDEX { smtpRecvMailAddrIndex } ::= { smtpRecvMailAddrTable 1 } SmtpRecvMailAddrEntry ::= SEQUENCE { smtpRecvMailAddrIndex INTEGER, smtpRecvMailAddr OCTET STRING, smtpRecvMailAddrStatus RowStatus } smtpRecvMailAddrIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Receivers' mail address index (1~8)." ::= { smtpRecvMailAddrEntry 1 } smtpRecvMailAddr OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Receivers' mail address." ::= { smtpRecvMailAddrEntry 2 } smtpRecvMailAddrStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Rowstatus of the receiver's mail address." ::= { smtpRecvMailAddrEntry 3 } igmpMulticastVlanStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable IGMP Multicast Vlan function." DEFVAL { disabled } ::= { companyISMVLAN 1 } -- ---------------------------------------------------------- -- igmpMulticastVlanTable Table -- ---------------------------------------------------------- igmpMulticastVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpMulticastVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the IGMP snooping multicast VLAN table." ::= { companyISMVLAN 2 } igmpMulticastVlanEntry OBJECT-TYPE SYNTAX IgmpMulticastVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of igmpMulticastVlanTable." INDEX { igmpMulticastVlanid} ::= { igmpMulticastVlanTable 1 } IgmpMulticastVlanEntry ::= SEQUENCE { igmpMulticastVlanid INTEGER, igmpMulticastVlanName DisplayString, igmpMulticastVlanSourcePort PortList, igmpMulticastVlanMemberPort PortList, igmpMulticastVlanTagMemberPort PortList, igmpMulticastVlanUntaggedSourcePort PortList, igmpMulticastVlanState INTEGER, igmpMulticastVlanReplaceSourceIp IpAddress, -- start DLINK_ISMVLAN_REMAP_REPLACE_PRIORITY igmpMulticastVlanRemapPriority INTEGER, igmpMulticastVlanReplacePriority INTEGER, -- end DLINK_ISMVLAN_REMAP_REPLACE_PRIORITY igmpMulticastVlanRowStatus RowStatus } igmpMulticastVlanid OBJECT-TYPE SYNTAX INTEGER (2..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry." ::= { igmpMulticastVlanEntry 1 } igmpMulticastVlanName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the VLAN name of the IGMP snooping multicast VLAN entry." ::= { igmpMulticastVlanEntry 2 } igmpMulticastVlanSourcePort OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the port list of the source ports of the IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports." ::= { igmpMulticastVlanEntry 3 } igmpMulticastVlanMemberPort OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the port list of the member ports of the IGMP snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports." ::= { igmpMulticastVlanEntry 4 } igmpMulticastVlanTagMemberPort OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the port list of the tag member ports of the IGMP snooping multicast VLAN." ::= { igmpMulticastVlanEntry 5 } igmpMulticastVlanUntaggedSourcePort OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the port list of the untag source ports of the IGMP snooping multicast VLAN." ::= { igmpMulticastVlanEntry 6 } igmpMulticastVlanState OBJECT-TYPE SYNTAX INTEGER{ enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object can be used to enable or disable the IGMP snooping multicast VLAN." ::= { igmpMulticastVlanEntry 7 } igmpMulticastVlanReplaceSourceIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The replacement source IP of this multicast VLAN." ::= { igmpMulticastVlanEntry 8 } -- start DLINK_ISMVLAN_REMAP_REPLACE_PRIORITY igmpMulticastVlanRemapPriority OBJECT-TYPE SYNTAX INTEGER (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The remap priority of this multicast VLAN." DEFVAL { -1 } ::= { igmpMulticastVlanEntry 9 } igmpMulticastVlanReplacePriority OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The replacement priority of this multicast VLAN." DEFVAL { disabled } ::= { igmpMulticastVlanEntry 10 } -- end DLINK_ISMVLAN_REMAP_REPLACE_PRIORITY igmpMulticastVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { igmpMulticastVlanEntry 11 } -- ----------------------------------------------------------------------------- -- igmpMulticastVlanGroupTable -- ----------------------------------------------------------------------------- igmpMulticastVlanGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpMulticastVlanGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table containing the IGMP snooping multicast VLAN group information" ::= { companyISMVLAN 3 } igmpMulticastVlanGroupEntry OBJECT-TYPE SYNTAX IgmpMulticastVlanGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the current IGMP snooping multicast VLAN group." INDEX { igmpMulticastVlanGroupVid, igmpMulticastVlanGroupFromIp, igmpMulticastVlanGroupToIp } ::= { igmpMulticastVlanGroupTable 1 } IgmpMulticastVlanGroupEntry ::= SEQUENCE { igmpMulticastVlanGroupVid INTEGER, igmpMulticastVlanGroupFromIp IpAddress, igmpMulticastVlanGroupToIp IpAddress, igmpMulticastVlanGroupStatus RowStatus } igmpMulticastVlanGroupVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the VID of the IGMP snooping multicast VLAN group." ::= { igmpMulticastVlanGroupEntry 1 } igmpMulticastVlanGroupFromIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the multicast address list for this VLAN." ::= { igmpMulticastVlanGroupEntry 2 } igmpMulticastVlanGroupToIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the multicast address list for this VLAN." ::= { igmpMulticastVlanGroupEntry 3 } igmpMulticastVlanGroupStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { igmpMulticastVlanGroupEntry 4 } -- ---------------------------------------------------------- -- multicastVlanTable Table -- ---------------------------------------------------------- multicastVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MulticastVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the IGMP/MLD snooping multicast VLAN table." ::= { companyISMVLAN 4 } multicastVlanEntry OBJECT-TYPE SYNTAX MulticastVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of multicastVlanTable." INDEX { multicastVlanid} ::= { multicastVlanTable 1 } MulticastVlanEntry ::= SEQUENCE { multicastVlanid INTEGER, multicastVlanName DisplayString, multicastVlanSourcePort PortList, multicastVlanMemberPort PortList, multicastVlanTagMemberPort PortList, multicastVlanUntaggedSourcePort PortList, multicastVlanState INTEGER, multicastVlanIgmpReplaceSourceIp IpAddress, multicastVlanMldReplaceSourceIp Ipv6Address, -- start DLINK_ISMVLAN_REMAP_REPLACE_PRIORITY multicastVlanRemapPriority INTEGER, multicastVlanReplacePriority INTEGER, -- end DLINK_ISMVLAN_REMAP_REPLACE_PRIORITY multicastVlanRowStatus RowStatus } multicastVlanid OBJECT-TYPE SYNTAX INTEGER (2..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the VLAN ID of the IGMP/MLD snooping multicast VLAN entry." ::= { multicastVlanEntry 1 } multicastVlanName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the VLAN name of the IGMP/MLD snooping multicast VLAN entry." ::= { multicastVlanEntry 2 } multicastVlanSourcePort OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the port list of the source ports of the IGMP/MLD snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from themember ports will be forwarded to the source ports." ::= { multicastVlanEntry 3 } multicastVlanMemberPort OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the port list of the member ports of the IGMP/MLD snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry and the IGMP control messages received from themember ports will be forwarded to the source ports." ::= { multicastVlanEntry 4 } multicastVlanTagMemberPort OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the port list of the tag member ports of the IGMP/MLD snooping multicast VLAN." ::= { multicastVlanEntry 5 } multicastVlanUntaggedSourcePort OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the port list of the untag source ports of the IGMP/MLD snooping multicast VLAN." ::= { multicastVlanEntry 6 } multicastVlanState OBJECT-TYPE SYNTAX INTEGER{ enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object can be used to enable or disable the IGMP/MLD snooping multicast VLAN." ::= { multicastVlanEntry 7 } multicastVlanIgmpReplaceSourceIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The replacement source IP of this IGMP snooping multicast VLAN." ::= { multicastVlanEntry 8 } multicastVlanMldReplaceSourceIp OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "The replacement source IP of this MLD snooping multicast VLAN." ::= { multicastVlanEntry 9 } -- start DLINK_ISMVLAN_REMAP_REPLACE_PRIORITY multicastVlanRemapPriority OBJECT-TYPE SYNTAX INTEGER (-1..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The remap priority of this multicast VLAN." DEFVAL { -1 } ::= { multicastVlanEntry 10 } multicastVlanReplacePriority OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The replacement priority of this multicast VLAN." DEFVAL { disabled } ::= { multicastVlanEntry 11 } -- end DLINK_ISMVLAN_REMAP_REPLACE_PRIORITY multicastVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { multicastVlanEntry 12 } -- ----------------------------------------------------------------------------- -- igmpMulticastVlanGroupTable -- ----------------------------------------------------------------------------- multicastVlanGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MulticastVlanGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table containing the IGMP/MLD snooping multicast VLAN group information" ::= { companyISMVLAN 5 } multicastVlanGroupEntry OBJECT-TYPE SYNTAX MulticastVlanGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of multicastVlanGroupTable." INDEX { multicastVlanGroupVid, multicastVlanGroupIpType, multicastVlanGroupFromIp, multicastVlanGroupToIp } ::= { multicastVlanGroupTable 1 } MulticastVlanGroupEntry ::= SEQUENCE { multicastVlanGroupVid INTEGER, multicastVlanGroupIpType INTEGER, multicastVlanGroupFromIp Ipv6Address, multicastVlanGroupToIp Ipv6Address, multicastVlanGroupStatus RowStatus } multicastVlanGroupVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the VID of the IGMP/MLD snooping multicast VLAN group." ::= { multicastVlanGroupEntry 1 } multicastVlanGroupIpType OBJECT-TYPE SYNTAX INTEGER { iPv4 (1), iPv6 (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of specifies the multicast address list for this VLAN." ::= { multicastVlanGroupEntry 2 } multicastVlanGroupFromIp OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the multicast address list for this VLAN." ::= { multicastVlanGroupEntry 3 } multicastVlanGroupToIp OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the multicast address list for this VLAN." ::= { multicastVlanGroupEntry 4 } multicastVlanGroupStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { multicastVlanGroupEntry 5 } -- ----------------------------------------------------------------------------- -- The Guest Vlan Group -- ----------------------------------------------------------------------------- pppoeGlobalState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "PPPoE global state" ::= { companyPPPoE 1 } pppoePortTable OBJECT-TYPE SYNTAX SEQUENCE OF PppoePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control PPPoE features of the device." ::= { companyPPPoE 2 } pppoePortEntry OBJECT-TYPE SYNTAX PppoePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in PPPoE table for each interface in the system." INDEX {pppoePortIndex} ::= { pppoePortTable 1 } PppoePortEntry ::= SEQUENCE { pppoePortIndex Integer32, pppoePortState INTEGER, pppoePortCircuitIDType INTEGER, pppoePortUDFString DisplayString, pppoePortCircuitIDVendor3String DisplayString, pppoePortRemoteIDType INTEGER, pppoePortRemoteIDVendor3String DisplayString } pppoePortIndex OBJECT-TYPE SYNTAX Integer32 (1..6) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface index of the port for the configuration in this entry applies." ::= { pppoePortEntry 1 } pppoePortState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "PPPoE per port state" ::= { pppoePortEntry 2 } pppoePortCircuitIDType OBJECT-TYPE SYNTAX INTEGER { ip (0), mac (1), udf (2), vendor2 (3), vendor3 (4) } MAX-ACCESS read-write STATUS current DESCRIPTION "PPPoE per port circuit ID type" ::= { pppoePortEntry 3 } pppoePortUDFString OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "PPPoE per port UDF string" ::= { pppoePortEntry 4 } pppoePortCircuitIDVendor3String OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "PPPoE per port circuit ID vendor3 string" ::= { pppoePortEntry 5 } pppoePortRemoteIDType OBJECT-TYPE SYNTAX INTEGER { default (0), vendor2 (1), vendor3 (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "PPPoE per port remote ID type" ::= { pppoePortEntry 6 } pppoePortRemoteIDVendor3String OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "PPPoE per port remote ID vendor3 string" ::= { pppoePortEntry 7 } -- ---------------------------------------------------------------- -- The RMON group -- ---------------------------------------------------------------- rmonGlobalState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is for enabling or disabling RMON function." ::= { companyRMON 1 } rmonStatistics OBJECT IDENTIFIER ::= { companyRMON 2 } rmonHistory OBJECT IDENTIFIER ::= { companyRMON 3 } rmonAlarm OBJECT IDENTIFIER ::= { companyRMON 4 } rmonEvent OBJECT IDENTIFIER ::= { companyRMON 5 } -- The Ethernet Statistics Group -- -- Implementation of the Ethernet Statistics group is optional. -- Consult the MODULE-COMPLIANCE macro for the authoritative -- conformance information for this MIB. -- -- The ethernet statistics group contains statistics measured by the -- probe for each monitored interface on this device. These -- statistics take the form of free running counters that start from -- zero when a valid entry is created. -- -- This group currently has statistics defined only for -- Ethernet interfaces. Each etherStatsEntry contains statistics -- for one Ethernet interface. The probe must create one -- etherStats entry for each monitored Ethernet interface -- on the device. rmonStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF RmonStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Ethernet statistics entries." ::= { rmonStatistics 1 } rmonStatsEntry OBJECT-TYPE SYNTAX RmonStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named etherStatsPkts.1" INDEX { rmonStatsIndex } ::= { rmonStatsTable 1 } RmonStatsEntry ::= SEQUENCE { rmonStatsIndex Integer32, rmonStatsDataSource OBJECT IDENTIFIER, rmonStatsOwner OwnerString, rmonStatsStatus RmonStatus } rmonStatsIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object uniquely identifies this etherStats entry." ::= { rmonStatsEntry 1 } rmonStatsDataSource OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "This object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated etherStatsStatus object is equal to valid(1)." ::= { rmonStatsEntry 2 } rmonStatsOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it." ::= { rmonStatsEntry 3 } rmonStatsStatus OBJECT-TYPE SYNTAX RmonStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this etherStats entry." ::= { rmonStatsEntry 4 } -- The History Control Group -- Implementation of the History Control group is optional. -- Consult the MODULE-COMPLIANCE macro for the authoritative -- conformance information for this MIB. -- -- The history control group controls the periodic statistical -- sampling of data from various types of networks. The -- historyControlTable stores configuration entries that each -- define an interface, polling period, and other parameters. -- Once samples are taken, their data is stored in an entry -- in a media-specific table. Each such entry defines one -- sample, and is associated with the historyControlEntry that -- caused the sample to be taken. Each counter in the -- etherHistoryEntry counts the same event as its similarly-named -- counterpart in the etherStatsEntry, except that each value here -- is a cumulative sum during a sampling period. -- -- If the probe keeps track of the time of day, it should start -- the first sample of the history at a time such that -- when the next hour of the day begins, a sample is -- started at that instant. This tends to make more -- user-friendly reports, and enables comparison of reports -- from different probes that have relatively accurate time -- of day. -- -- The probe is encouraged to add two history control entries -- per monitored interface upon initialization that describe a short -- term and a long term polling period. Suggested parameters are 30 -- seconds for the short term polling period and 30 minutes for -- the long term period. rmonHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF RmonHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of history control entries." ::= { rmonHistory 1 } rmonHistoryEntry OBJECT-TYPE SYNTAX RmonHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of parameters that set up a periodic sampling of statistics. As an example, an instance of the historyControlInterval object might be named historyControlInterval.2" INDEX { rmonHistoryIndex } ::= { rmonHistoryTable 1 } RmonHistoryEntry ::= SEQUENCE { rmonHistoryIndex Integer32, rmonHistoryDataSource OBJECT IDENTIFIER, rmonHistoryBucketsRequested Integer32, rmonHistoryInterval Integer32, rmonHistoryOwner OwnerString, rmonHistoryStatus RmonStatus } rmonHistoryIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device." ::= { rmonHistoryEntry 1 } rmonHistoryDataSource OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated historyControlStatus object is equal to valid(1)." ::= { rmonHistoryEntry 2 } rmonHistoryBucketsRequested OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry. When this object is created or modified, the probe should set historyControlBucketsGranted as closely to this object as is possible for the particular probe implementation and available resources." DEFVAL { 50 } ::= { rmonHistoryEntry 3 } rmonHistoryInterval OBJECT-TYPE SYNTAX Integer32 (1..3600) UNITS "Seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControlEntry. This interval can be set to any number of seconds between 1 and 3600 (1 hour). Because the counters in a bucket may overflow at their maximum value with no indication, a prudent manager will take into account the possibility of overflow in any of the associated counters. It is important to consider the minimum time in which any counter could overflow on a particular media type and set the historyControlInterval object to a value less than this interval. This is typically most important for the 'octets' counter in any media-specific table. For example, on an Ethernet network, the etherHistoryOctets counter could overflow in about one hour at the Ethernet's maximum utilization. This object may not be modified if the associated historyControlStatus object is equal to valid(1)." DEFVAL { 1800 } ::= { rmonHistoryEntry 4 } rmonHistoryOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it." ::= { rmonHistoryEntry 5 } rmonHistoryStatus OBJECT-TYPE SYNTAX RmonStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if this historyControlEntry is not equal to valid(1)." ::= { rmonHistoryEntry 6 } -- The Alarm Group -- Implementation of the Alarm group is optional. The Alarm Group -- requires the implementation of the Event group. -- Consult the MODULE-COMPLIANCE macro for the authoritative -- conformance information for this MIB. -- -- The Alarm group periodically takes statistical samples from -- variables in the probe and compares them to thresholds that have -- been configured. The alarm table stores configuration -- entries that each define a variable, polling period, and -- threshold parameters. If a sample is found to cross the -- threshold values, an event is generated. Only variables that -- resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, -- Counter32, Counter64, Gauge32, or TimeTicks) may be monitored in -- this way. -- -- This function has a hysteresis mechanism to limit the generation -- of events. This mechanism generates one event as a threshold -- is crossed in the appropriate direction. No more events are -- generated for that threshold until the opposite threshold is -- crossed. -- -- In the case of a sampling a deltaValue, a probe may implement -- this mechanism with more precision if it takes a delta sample -- twice per period, each time comparing the sum of the latest two -- samples to the threshold. This allows the detection of threshold -- crossings that span the sampling boundary. Note that this does -- not require any special configuration of the threshold value. -- It is suggested that probes implement this more precise algorithm. rmonAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF RmonAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of alarm entries." ::= { rmonAlarm 1 } rmonAlarmEntry OBJECT-TYPE SYNTAX RmonAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of parameters that set up a periodic checking for alarm conditions. For example, an instance of the alarmValue object might be named alarmValue.8" INDEX { rmonAlarmIndex } ::= { rmonAlarmTable 1 } RmonAlarmEntry ::= SEQUENCE { rmonAlarmIndex Integer32, rmonAlarmInterval Integer32, rmonAlarmVariable OBJECT IDENTIFIER, rmonAlarmSampleType INTEGER, rmonAlarmRisingThreshold Integer32, rmonAlarmFallingThreshold Integer32, rmonAlarmRisingEventIndex Integer32, rmonAlarmFallingEventIndex Integer32, rmonAlarmOwner OwnerString, rmonAlarmStatus RmonStatus } rmonAlarmIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "An index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device." ::= { rmonAlarmEntry 1 } rmonAlarmInterval OBJECT-TYPE SYNTAX Integer32 UNITS "Seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be taken in the case of deltaValue sampling - the interval should be set short enough that the sampled variable is very unlikely to increase or decrease by more than 2^31 - 1 during a single sampling interval. This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 2 } rmonAlarmVariable OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter32, Counter64, Gauge, or TimeTicks) may be sampled. Because SNMP access control is articulated entirely in terms of the contents of MIB views, no access control mechanism exists that can restrict the value of this object to identify only those objects that exist in a particular MIB view. Because there is thus no acceptable means of restricting the read access that could be obtained through the alarm mechanism, the probe must only grant write access to this object in those views that have read access to all objects on the probe. During a set operation, if the supplied variable name is not available in the selected MIB view, a badValue error must be returned. If at any time the variable name of an established alarmEntry is no longer available in the selected MIB view, the probe must change the status of this alarmEntry to invalid(4). This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 3 } rmonAlarmSampleType OBJECT-TYPE SYNTAX INTEGER { absoluteValue(1), deltaValue(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), the value of the selected variable will be compared directly with the thresholds at the end of the sampling interval. If the value of this object is deltaValue(2), the value of the selected variable at the last sample will be subtracted from the current value, and the difference compared with the thresholds. This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 4 } rmonAlarmRisingThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "A threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval was less than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is greater than or equal to this threshold and the associated alarmStartupAlarm is equal to risingAlarm(1) or risingOrFallingAlarm(3). After a rising event is generated, another such event will not be generated until the sampled value falls below this threshold and reaches the alarmFallingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 5 } rmonAlarmFallingThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "A threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was greater than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is less than or equal to this threshold and the associated alarmStartupAlarm is equal to fallingAlarm(2) or risingOrFallingAlarm(3). After a falling event is generated, another such event will not be generated until the sampled value rises above this threshold and reaches the alarmRisingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 6 } rmonAlarmRisingEventIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 7 } rmonAlarmFallingEventIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1)." ::= { rmonAlarmEntry 8 } rmonAlarmOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it." ::= { rmonAlarmEntry 9 } rmonAlarmStatus OBJECT-TYPE SYNTAX RmonStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this alarm entry." ::= { rmonAlarmEntry 10 } -- The Event Group -- Implementation of the Event group is optional. -- Consult the MODULE-COMPLIANCE macro for the authoritative -- conformance information for this MIB. -- -- The Event group controls the generation and notification -- of events from this device. Each entry in the eventTable -- describes the parameters of the event that can be triggered. -- Each event entry is fired by an associated condition located -- elsewhere in the MIB. An event entry may also be associated -- with a function elsewhere in the MIB that will be executed -- when the event is generated. For example, a channel may -- be turned on or off by the firing of an event. -- -- Each eventEntry may optionally specify that a log entry -- be created on its behalf whenever the event occurs. -- Each entry may also specify that notification should -- occur by way of SNMP trap messages. In this case, the -- community for the trap message is given in the associated -- eventCommunity object. The enterprise and specific trap -- fields of the trap are determined by the condition that -- triggered the event. Two traps are defined: risingAlarm and -- fallingAlarm. If the eventTable is triggered by a condition -- specified elsewhere, the enterprise and specific trap fields -- must be specified for traps generated for that condition. rmonEventTable OBJECT-TYPE SYNTAX SEQUENCE OF RmonEventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of events to be generated." ::= { rmonEvent 1 } rmonEventEntry OBJECT-TYPE SYNTAX RmonEventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of parameters that describe an event to be generated when certain conditions are met. As an example, an instance of the eventLastTimeSent object might be named eventLastTimeSent.6" INDEX { rmonEventIndex } ::= { rmonEventTable 1 } RmonEventEntry ::= SEQUENCE { rmonEventIndex Integer32, rmonEventDescription DisplayString, rmonEventType INTEGER, rmonEventCommunity OCTET STRING, rmonEventOwner OwnerString, rmonEventStatus RmonStatus } rmonEventIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "An index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur." ::= { rmonEventEntry 1 } rmonEventDescription OBJECT-TYPE SYNTAX DisplayString (SIZE (0..127)) MAX-ACCESS read-create STATUS current DESCRIPTION "A comment describing this event entry." ::= { rmonEventEntry 2 } rmonEventType OBJECT-TYPE SYNTAX INTEGER { none(1), log(2), snmptrap(3), -- send an SNMP trap logandtrap(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-trap, an SNMP trap is sent to one or more management stations." ::= { rmonEventEntry 3 } rmonEventCommunity OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..127)) MAX-ACCESS read-create STATUS current DESCRIPTION "If an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string." ::= { rmonEventEntry 4 } rmonEventOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has associated entries in the log table, all connected management stations should retrieve those log entries, as they may have significance to all management stations connected to this device" ::= { rmonEventEntry 5 } rmonEventStatus OBJECT-TYPE SYNTAX RmonStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent." ::= { rmonEventEntry 6 } -- ---------------------------------------------------------------- -- The Neighbor Setting group -- ---------------------------------------------------------------- neighborTable OBJECT-TYPE SYNTAX SEQUENCE OF NeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the Neighbor Cache Table." ::= { companyNeighbor 1 } neighborEntry OBJECT-TYPE SYNTAX NeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Neighbor cache entry containing the ifindex and ipv6 addr." INDEX { neighborIfindex, neighborIPv6Addr, neighborMACAddr} ::= { neighborTable 1 } NeighborEntry ::= SEQUENCE { neighborIfindex INTEGER, neighborIPv6Addr Ipv6Address, neighborMACAddr MacAddress, neighborType INTEGER, neighborCacheState INTEGER, neighborActiveStatus INTEGER, neighborRowStatus RowStatus } neighborIfindex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index of the Neighbor entry." ::= { neighborEntry 1 } neighborIPv6Addr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "Allows the entry of an IP address that will be a Neighbor entry into the Neighbor Cache Table." ::= { neighborEntry 2 } neighborMACAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address associated of the Neighbor entry." ::= { neighborEntry 3 } neighborType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type associated of the Neighbor entry." ::= { neighborEntry 4 } neighborCacheState OBJECT-TYPE SYNTAX INTEGER { static(1), reachable(2), incomplete(3), stale(4), delay(5), probe(6), notinservice(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type associated of the Neighbor entry." ::= { neighborEntry 5 } neighborActiveStatus OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The active status of the Neighbor entry." ::= { neighborEntry 6 } neighborRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of an entry in the Neighbor Cache Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available." ::= { neighborEntry 7 } dhcpv6RelayControl OBJECT IDENTIFIER ::= { companyDHCPv6Relay 1 } dhcpv6RelayManagement OBJECT IDENTIFIER ::= { companyDHCPv6Relay 2 } dhcpv6RelayOption37 OBJECT IDENTIFIER ::= { companyDHCPv6Relay 3 } dhcpv6RelayOption38 OBJECT IDENTIFIER ::= { companyDHCPv6Relay 4 } dhcpv6RelayOption18 OBJECT IDENTIFIER ::= { companyDHCPv6Relay 5 } -- ---------------------------------------------------------- -- The DHCPv6 Relay -- ---------------------------------------------------------- -- The DHCPv6 Relay Control dhcpv6RelayState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCPv6 relay function is enabled or disabled." ::= { dhcpv6RelayControl 1 } dhcpv6RelayHopCount OBJECT-TYPE SYNTAX INTEGER (1..16) MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the maximum number of router hops that the DHCPv6 packets can cross." ::= { dhcpv6RelayControl 2 } -- The DHCPv6 Relay Management -- The DHCPv6 Relay Interface Settings Table dhcpv6RelayInterfaceSettingsTable OBJECT-TYPE SYNTAX SEQUENCE OF DHCPv6RelayInterfaceSettings MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the IP address as a destination to forward (relay) DHCP packets to." ::= { dhcpv6RelayManagement 1 } dhcpv6RelayInterfaceSettingsEntry OBJECT-TYPE SYNTAX DHCPv6RelayInterfaceSettings MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information indicates the IP address as a destination to forward (relay) DHCP packets to." INDEX { dhcpv6RelayInterface, dhcpv6RelayServerIP} ::= { dhcpv6RelayInterfaceSettingsTable 1 } DHCPv6RelayInterfaceSettings ::= SEQUENCE { dhcpv6RelayInterface DisplayString, dhcpv6RelayServerIP Ipv6Address, dhcpv6RelayInterfaceSettingsRowStatus RowStatus } dhcpv6RelayInterface OBJECT-TYPE SYNTAX DisplayString (SIZE(0..12)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum number of router hops that the DHCPv6 packets can cross." ::= { dhcpv6RelayInterfaceSettingsEntry 1 } dhcpv6RelayServerIP OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the DHCP server IP address." ::= { dhcpv6RelayInterfaceSettingsEntry 2 } dhcpv6RelayInterfaceSettingsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { dhcpv6RelayInterfaceSettingsEntry 99 } -- The DHCPv6 Relay Option37 dhcpv6RelayOption37State OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCPv6 relay option 37 function is enabled or disabled." ::= { dhcpv6RelayOption37 1 } dhcpv6RelayOption37CheckState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCPv6 relay option 37 Check function is enabled or disabled." ::= { dhcpv6RelayOption37 2 } -- dhcpv6RelayOption37Policy OBJECT-TYPE -- SYNTAX INTEGER { -- replace(1), -- drop(2), -- keep(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "This object indicates DHCPv6 relay option 37 policy." -- ::= { dhcpv6RelayOption37 3 } dhcpv6RelayOption37RemoteIDType OBJECT-TYPE SYNTAX INTEGER { default(0), cid_with_user_define(1), user_define(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the type of remote ID." ::= { dhcpv6RelayOption37 3 } dhcpv6RelayOption37RemoteID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object displays the current remote ID of the device. If RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If RemoteIDType is set to user-defined, a new value can be written to this object." ::= { dhcpv6RelayOption37 4 } dhcpv6RelayOpt38Table OBJECT-TYPE SYNTAX SEQUENCE OF Dhcpv6RelayOpt38Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control port security features of the device." ::= { dhcpv6RelayOption38 1 } dhcpv6RelayOpt38Entry OBJECT-TYPE SYNTAX Dhcpv6RelayOpt38Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in port security table for each interface in the system." INDEX { dhcpv6RelayOpt38PortIndex } ::= { dhcpv6RelayOpt38Table 1 } Dhcpv6RelayOpt38Entry ::= SEQUENCE { dhcpv6RelayOpt38PortIndex Integer32, dhcpv6RelayOpt38PortState INTEGER, dhcpv6RelayOpt38PortType INTEGER, dhcpv6RelayOpt38PortID DisplayString } dhcpv6RelayOpt38PortIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index for which the configuration in this entry applies." ::= { dhcpv6RelayOpt38Entry 1 } dhcpv6RelayOpt38PortState OBJECT-TYPE SYNTAX INTEGER { disabled (0), enabled (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable / disable option 38 port state." ::= { dhcpv6RelayOpt38Entry 2 } dhcpv6RelayOpt38PortType OBJECT-TYPE SYNTAX INTEGER { default (0), user-defined (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configure option 38 port Type." ::= {dhcpv6RelayOpt38Entry 3} dhcpv6RelayOpt38PortID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Configure option 38 port ID. Only works when type is user-defined" ::= {dhcpv6RelayOpt38Entry 4} -- The DHCPv6 Relay Option18 dhcpv6RelayOption18State OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCPv6 relay option 18 function is enabled or disabled." ::= { dhcpv6RelayOption18 1 } dhcpv6RelayOption18CheckState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates DHCPv6 relay option 18 Check function is enabled or disabled." ::= { dhcpv6RelayOption18 2 } dhcpv6RelayOption18InterfaceIDType OBJECT-TYPE SYNTAX INTEGER { default(0), cid(1), vendor1(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the type of Interface ID." ::= { dhcpv6RelayOption18 3 } -- ----------------------------------------------------------------- -- 1. MAC-based Access Control Settings -- ----------------------------------------------------------------- macBasedCtrlGroup OBJECT IDENTIFIER ::= { companyMacAuthGroup 1 } -------------------------------------------- macBasedCtrlState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable MAC-based Access Control Global Settings." ::= { macBasedCtrlGroup 1 } macBasedMethod OBJECT-TYPE SYNTAX INTEGER { radius(1), local(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Select MAC-based Access Control Methods." DEFVAL { radius } ::= { macBasedCtrlGroup 2 } macBasedRadiusPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "Set the password about the method Mac-Based Authentication, the maximum length are 32 chars." ::= { macBasedCtrlGroup 3 } macBasedRadiusAuthStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of Radius Authorization. " ::= { macBasedCtrlGroup 4 } macBasedLocalAuthStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of Local Authorization. " ::= { macBasedCtrlGroup 5 } macBasedTrapStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of Trap of MAC-based Authorization." ::= { macBasedCtrlGroup 6 } macBasedLogStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "" ::= { macBasedCtrlGroup 7 } macBasedMaxUsr OBJECT-TYPE SYNTAX Integer32 (1..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "" DEFVAL { 128 } ::= { macBasedCtrlGroup 8 } macBasedPortCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF MacBasedPortCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { macBasedCtrlGroup 11 } macBasedPortCtrlEntry OBJECT-TYPE SYNTAX MacBasedPortCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { macBasedPortCtrlIndex } ::= { macBasedPortCtrlTable 1 } MacBasedPortCtrlEntry ::= SEQUENCE { macBasedPortCtrlIndex Integer32, macBasedPortCtrlState INTEGER, macBasedPortCtrlAgingTime Integer32, macBasedPortCtrlBlockTime Integer32, macBasedPortCtrlMaxUsr Integer32 } macBasedPortCtrlIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { macBasedPortCtrlEntry 1 } macBasedPortCtrlState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "" ::= { macBasedPortCtrlEntry 2 } macBasedPortCtrlAgingTime OBJECT-TYPE SYNTAX Integer32 (1..1440) MAX-ACCESS read-write STATUS current DESCRIPTION "" ::= { macBasedPortCtrlEntry 3 } macBasedPortCtrlBlockTime OBJECT-TYPE SYNTAX Integer32 (0..300) MAX-ACCESS read-write STATUS current DESCRIPTION "" ::= { macBasedPortCtrlEntry 4 } macBasedPortCtrlMaxUsr OBJECT-TYPE SYNTAX Integer32 (1..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "" DEFVAL { 128 } ::= { macBasedPortCtrlEntry 5 } -- ----------------------------------------------------------------- -- 2. MAC-based Access Control Local Settings -- ----------------------------------------------------------------- macBasedCtrlLocalGroup OBJECT IDENTIFIER ::= { companyMacAuthGroup 2 } -------------------------------------------- macBasedCtrlLocalTable OBJECT-TYPE SYNTAX SEQUENCE OF MacBasedCtrlLocalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { macBasedCtrlLocalGroup 1 } macBasedCtrlLocalEntry OBJECT-TYPE SYNTAX MacBasedCtrlLocalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { macBasedCtrlLocalMacAddress, macBasedCtrlLocalVID } ::= { macBasedCtrlLocalTable 1 } MacBasedCtrlLocalEntry ::= SEQUENCE { macBasedCtrlLocalMacAddress MacAddress, macBasedCtrlLocalVID INTEGER, macBasedCtrlLocalVlanName SnmpAdminString, macBasedCtrlLocalRowStatus RowStatus } macBasedCtrlLocalMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MacAddress of the MAC-based Access Control Local Setting Table." ::= { macBasedCtrlLocalEntry 1 } macBasedCtrlLocalVID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the MAC-based Access Control Local Setting entry." ::= { macBasedCtrlLocalEntry 2 } macBasedCtrlLocalVlanName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "An administratively assigned string, which may be used to identify the VLAN." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { macBasedCtrlLocalEntry 3 } macBasedCtrlLocalRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The Row status of an entry in the MAC-based Access Control Local Setting Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available" ::= { macBasedCtrlLocalEntry 4 } -- ----------------------------------------------------------------- -- 3. MAC-based Access Control Authentication State -- ----------------------------------------------------------------- macBasedCtrlAuthGroup OBJECT IDENTIFIER ::= { companyMacAuthGroup 3 } -------------------------------------------- macBasedCtrlAuthTable OBJECT-TYPE SYNTAX SEQUENCE OF MacBasedCtrlAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" ::= { macBasedCtrlAuthGroup 1 } macBasedCtrlAuthEntry OBJECT-TYPE SYNTAX MacBasedCtrlAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { macBasedCtrlAuthPort, macBasedCtrlAuthMacAddress, macBasedCtrlAuthRxVID } ::= { macBasedCtrlAuthTable 1 } MacBasedCtrlAuthEntry ::= SEQUENCE { macBasedCtrlAuthPort Integer32, macBasedCtrlAuthMacAddress MacAddress, macBasedCtrlAuthRxVID INTEGER, macBasedCtrlAuthState INTEGER, macBasedCtrlAuthVID INTEGER, macBasedCtrlAuthPriority INTEGER, macBasedCtrlAuthAgingTime INTEGER, macBasedCtrlAuthBlockTime INTEGER } macBasedCtrlAuthPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { macBasedCtrlAuthEntry 1 } macBasedCtrlAuthMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MacAddress of the MAC-based Access Control Authentication State Table." ::= { macBasedCtrlAuthEntry 2 } macBasedCtrlAuthRxVID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { macBasedCtrlAuthEntry 3 } macBasedCtrlAuthState OBJECT-TYPE SYNTAX INTEGER { authenticating(1), authenticated(2), blocked(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { macBasedCtrlAuthEntry 4 } macBasedCtrlAuthVID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { macBasedCtrlAuthEntry 5 } macBasedCtrlAuthPriority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { macBasedCtrlAuthEntry 6 } macBasedCtrlAuthAgingTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { macBasedCtrlAuthEntry 7 } macBasedCtrlAuthBlockTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { macBasedCtrlAuthEntry 8 } -- ------------------------------------------------------------- -- groups in the WAC Global Setting Auth MIB -- ------------------------------------------------------------- wacAuthCtrl OBJECT IDENTIFIER ::= { companyWACAuthGroup 1 } -- ----------------------------------------------------------------------------- -- wacAuthCtrl -- ----------------------------------------------------------------------------- wacStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable WAC Global Settings" ::= { wacAuthCtrl 1 } wacVirtualIPv4 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Virtual IPv4" ::= { wacAuthCtrl 2 } wacVirtualIPv6 OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-write STATUS current DESCRIPTION "Virtual IPv6" ::= { wacAuthCtrl 3 } wacRedirPath OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Redirection Path" ::= { wacAuthCtrl 4 } wacClrRedirPath OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "yes/no WAC Clear Redirection path Settings" ::= { wacAuthCtrl 5 } wacRadiusAuth OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable WAC RADIUS AUTH Settings" ::= { wacAuthCtrl 6 } waclocalAuth OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable WAC LOCAL AUTH Settings" ::= { wacAuthCtrl 7 } wacAuthMethod OBJECT-TYPE SYNTAX INTEGER { radius(1), local(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable WAC Auth Method Settings" ::= { wacAuthCtrl 8 } wacAuthPortMethod OBJECT-TYPE SYNTAX INTEGER { http(1), https(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authorization Port Method" ::= { wacAuthCtrl 9 } wacAuthPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "HTTP(s) Port." ::= { wacAuthCtrl 10 } -- ------------------------------------------------------------- -- groups in the User Settings Control MIB -- ------------------------------------------------------------- wacUsrCtrl OBJECT IDENTIFIER ::= { companyWACAuthGroup 2 } -- ----------------------------------------------------------------------------- -- wacUsrCtrl -- ----------------------------------------------------------------------------- wacUsrCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF WACUsrCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself." ::= { wacUsrCtrl 1 } wacUsrCtrlEntry OBJECT-TYPE SYNTAX WACUsrCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration information for an Authenticator Port." INDEX { authUserName } ::= { wacUsrCtrlTable 1 } WACUsrCtrlEntry ::= SEQUENCE { authUserName SnmpAdminString, authUserVID INTEGER, authUserPassword DisplayString, authUserStatus RowStatus } authUserName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "The unique index value of a row in this table. This object is used to set 802.1X Local user name, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark." ::= { wacUsrCtrlEntry 1 } authUserVID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The ID of VLAN that you want this interface to be in. It must be a exist vlan id." ::= { wacUsrCtrlEntry 2 } authUserPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to set 802.1X Local user Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark." ::= { wacUsrCtrlEntry 3 } authUserStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row in the swAuthUserTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthUserName objects must be explicitly set." ::= { wacUsrCtrlEntry 4 } -- ------------------------------------------------------------- -- groups in the Port Settings Control MIB -- ------------------------------------------------------------- wacPortCtrl OBJECT IDENTIFIER ::= { companyWACAuthGroup 3 } -- ----------------------------------------------------------------------------- -- wacPortCtrl -- ----------------------------------------------------------------------------- -- Port Control Table wacPortCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF WACPortCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control the port specific parameters of the device like speed, duplex mode, etc." ::= { wacPortCtrl 1 } wacPortCtrlEntry OBJECT-TYPE SYNTAX WACPortCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system. Index to the table is the interface index of the port." INDEX { wacPortCtrlIndex } ::= { wacPortCtrlTable 1 } WACPortCtrlEntry ::= SEQUENCE { wacPortCtrlIndex Integer32, wacPortCtrlState INTEGER, wacPortCtrlAgetime INTEGER, wacPortCtrlBlocktime INTEGER } wacPortCtrlIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface index of the port for the configuration in this entry applies." ::= { wacPortCtrlEntry 1 } wacPortCtrlState OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables / disables flow control for the interface." ::= { wacPortCtrlEntry 2 } wacPortCtrlAgetime OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Aging time" ::= { wacPortCtrlEntry 3 } wacPortCtrlBlocktime OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Aging time" ::= { wacPortCtrlEntry 4 } -- ------------------------------------------------------------- -- groups in the Authentication State Control MIB -- ------------------------------------------------------------- wacAuthState OBJECT IDENTIFIER ::= { companyWACAuthGroup 4 } -- ----------------------------------------------------------------------------- -- wacAuthState for IPv4(and IPv6) -- ----------------------------------------------------------------------------- wacAuthStateTable OBJECT-TYPE SYNTAX SEQUENCE OF WACAuthStateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the Auth States" ::= { wacAuthState 1 } wacAuthStateEntry OBJECT-TYPE SYNTAX WACAuthStateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Auth State entry containing the mac and forwarding port." INDEX {wacAuthStatePort, wacAuthStateMac, wacAuthStateRXVID} ::= { wacAuthStateTable 1 } WACAuthStateEntry ::= SEQUENCE { wacAuthStatePort INTEGER, wacAuthStateMac MacAddress, wacAuthStateRXVID INTEGER, wacAuthStateflag INTEGER, wacAuthStateVID INTEGER, wacAuthAssignPriority INTEGER, wacAuthStateAgetime INTEGER, wacAuthStateRowStatus RowStatus } wacAuthStatePort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The auth port state of the Auth State entry." ::= { wacAuthStateEntry 1 } wacAuthStateMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The auth state mac of the Auth State entry." ::= { wacAuthStateEntry 2 } wacAuthStateRXVID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The Rx VID of the Auth State entry." ::= { wacAuthStateEntry 3 } wacAuthStateflag OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The auth state flag of the Auth State entry." ::= { wacAuthStateEntry 4 } wacAuthStateVID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The auth state VID of the Auth State entry." ::= { wacAuthStateEntry 5 } wacAuthAssignPriority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The auth assign priority of the Auth State entry." ::= { wacAuthStateEntry 6 } wacAuthStateAgetime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The auth state age time of the Auth State entry." ::= { wacAuthStateEntry 7 } wacAuthStateRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The auth state row status." ::= { wacAuthStateEntry 99 } -- ---------------------------------------------------------------------------- -- The Vlan Mac Map Table -- ---------------------------------------------------------------------------- macBasedVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MacBasedVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information on Vlan-MAC address mapping." ::= { companyMacBasedVlan 1 } macBasedVlanEntry OBJECT-TYPE SYNTAX MacBasedVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry that contains Vlan-MAC address mapping." INDEX { vlanMacMapIndex } ::= { macBasedVlanTable 1 } MacBasedVlanEntry ::= SEQUENCE { vlanMacMapIndex Integer32, vlanMacMapAddr MacAddress, vlanMacMapAddrMask MacAddress, vlanMacMapVid VlanIndex, vlanMacStatus DisplayString, vlanMacType DisplayString, vlanMacMapRowStatus RowStatus } vlanMacMapIndex OBJECT-TYPE SYNTAX Integer32 (1..128) MAX-ACCESS read-only STATUS current DESCRIPTION "Index of cmMacBasedVlanEntry. This object indicates the mac vlan entry for which the configurations in cmMacBasedVlanEntry is to be done." ::= { macBasedVlanEntry 1 } vlanMacMapAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The Mac address for which the Vlan mapping is present in the entry." ::= { macBasedVlanEntry 2 } vlanMacMapAddrMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The Mac address for which the Vlan mapping is present in the entry." ::= { macBasedVlanEntry 3 } vlanMacMapVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-write STATUS current DESCRIPTION "The Vlan to which the mac address of this entry is mapped to." ::= { macBasedVlanEntry 4 } vlanMacStatus OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The status given to the mac-vlan entry." ::= { macBasedVlanEntry 5 } vlanMacType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The type given to the mac-vlan entry." ::= { macBasedVlanEntry 6 } vlanMacMapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The row status of the entry." ::= { macBasedVlanEntry 99 } macBasedVlanMethod OBJECT-TYPE SYNTAX INTEGER { single(1), range(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "A method of Vlan-MAC address mapping." ::= { companyMacBasedVlan 2 } -- ---------------------------------------------------------- -- The sfpVendorInfoTable -- ---------------------------------------------------------- sfpVendorInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF SfpVendorInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the IP address as a destination to forward (relay) DHCP packets to." ::= { companySfpVendorInfo 1 } sfpVendorInfoEntry OBJECT-TYPE SYNTAX SfpVendorInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information indicates the IP address as a destination to forward (relay) DHCP packets to." INDEX { sfpPortIndex } ::= { sfpVendorInfoTable 1 } SfpVendorInfoEntry ::= SEQUENCE { sfpPortIndex Integer32, sfpConnectorType DisplayString, sfpTranceiverCode DisplayString, sfpBaudRate DisplayString, sfpVendorName DisplayString, sfpVendorOui DisplayString, sfpVendorPn DisplayString, sfpVendorRev DisplayString, sfpWavelength DisplayString, sfpVendorSn DisplayString, sfpDateCode DisplayString } sfpPortIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { sfpVendorInfoEntry 1 } sfpConnectorType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= {sfpVendorInfoEntry 2} sfpTranceiverCode OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= {sfpVendorInfoEntry 3} sfpBaudRate OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= {sfpVendorInfoEntry 4} sfpVendorName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= {sfpVendorInfoEntry 5} sfpVendorOui OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= {sfpVendorInfoEntry 6} sfpVendorPn OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= {sfpVendorInfoEntry 7} sfpVendorRev OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= {sfpVendorInfoEntry 8} sfpWavelength OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= {sfpVendorInfoEntry 9} sfpVendorSn OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= {sfpVendorInfoEntry 10} sfpDateCode OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= {sfpVendorInfoEntry 11} -- -------------------------------------------------------------------------- ddmCtrl OBJECT IDENTIFIER ::={companyDDM 1} ddmInfo OBJECT IDENTIFIER ::={companyDDM 2} -- -------------------------------------------------------------------------- -- DdmCtrl -- -------------------------------------------------------------------------- ddmPowerUnit OBJECT-TYPE SYNTAX INTEGER { mw(0), dbm(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the TX/RX power global unit." DEFVAL{mw} ::= {ddmCtrl 1} --ddmActionMgmt ddmActionMgmtTable OBJECT-TYPE SYNTAX SEQUENCE OF DdmActionMgmtEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "This table contains the configuration of the action taken when any parameter exceeds its threshold." ::= {ddmCtrl 2} ddmActionMgmtEntry OBJECT-TYPE SYNTAX DdmActionMgmtEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "This is an entry of the swDdmConfigActionTable." INDEX {ddmActionPort } ::= {ddmActionMgmtTable 1} DdmActionMgmtEntry ::= SEQUENCE { ddmActionPort INTEGER, ddmActionState INTEGER, ddmActionShutdown INTEGER } ddmActionPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the port." ::= {ddmActionMgmtEntry 1} ddmActionState OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "This object indicates the action type." ::= {ddmActionMgmtEntry 2} ddmActionShutdown OBJECT-TYPE SYNTAX INTEGER { none(0), alarm(1), warning(2) } MAX-ACCESS read-write STATUS obsolete DESCRIPTION "This object indicates the action type." ::= {ddmActionMgmtEntry 3} --ddmThresholdMgmt ddmThresholdMgmtTable OBJECT-TYPE SYNTAX SEQUENCE OF DdmThresholdMgmtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains DDM temperature configuration information." ::= {ddmCtrl 3} ddmThresholdMgmtEntry OBJECT-TYPE SYNTAX DdmThresholdMgmtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is an entry of the swDdmConfigThresholdTable." INDEX {ddmThresholdPort ,ddmThresholdType} ::= {ddmThresholdMgmtTable 1} DdmThresholdMgmtEntry ::= SEQUENCE { ddmThresholdPort INTEGER, ddmThresholdType INTEGER, ddmHighAlarm DisplayString, ddmLowAlarm DisplayString, ddmHighWarning DisplayString, ddmLowWarning DisplayString } ddmThresholdPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the port." ::= {ddmThresholdMgmtEntry 1} ddmThresholdType OBJECT-TYPE SYNTAX INTEGER{ temperature(0), voltage(1), bias(2), txPower(3), rxPower(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the threshold type." ::= {ddmThresholdMgmtEntry 2} ddmHighAlarm OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the high alarm threshold value to be configured. As the value is a floating point data type, the DisplayString type is used to define this parameter." ::= {ddmThresholdMgmtEntry 3} ddmLowAlarm OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the low alarm threshold value to be configured. As the value is a floating data type, the DisplayString type is used to define this parameter." ::= {ddmThresholdMgmtEntry 4} ddmHighWarning OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the high warning threshold value to be configured. As the value is a floating data type, the DisplayString type is used to define this parameter." ::= {ddmThresholdMgmtEntry 5} ddmLowWarning OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the low warning threshold value to be configured. As the value is a floating data type, the DisplayString type is used to define this parameter." ::= {ddmThresholdMgmtEntry 6} -- -------------------------------------------------------------------------- -- DdmInfo -- -------------------------------------------------------------------------- ddmStatus OBJECT IDENTIFIER ::= { ddmInfo 1 } --DdmStatus ddmStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF DdmStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the DDM status information." ::= {ddmStatus 1} ddmStatusEntry OBJECT-TYPE SYNTAX DdmStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is an entry of the ddmStatusTable." INDEX {ddmStatusPort} ::= {ddmStatusTable 1} DdmStatusEntry ::= SEQUENCE { ddmStatusPort INTEGER, ddmTemperature DisplayString, ddmVoltage DisplayString, ddmBiasCurrent DisplayString, ddmTxPower DisplayString, ddmRxPower DisplayString } ddmStatusPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the port." ::= {ddmStatusEntry 1} ddmTemperature OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the real time value of the temperature. As the value is a floating point data type, the DisplayString type is used to define this parameter." ::= {ddmStatusEntry 2} ddmVoltage OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the real time value of the supply voltage. As the value value is a floating point data type, the DisplayString type is used to define this parameter." ::= {ddmStatusEntry 3} ddmBiasCurrent OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the real time value of the tx bias." ::= {ddmStatusEntry 4} ddmTxPower OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the real time value of the tx power. As the value is a floating point data type, the DisplayString type is used to define this parameter." ::= {ddmStatusEntry 5} ddmRxPower OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the real time value of the rx power. As the value is a floating data type, the DisplayString type is used to define this parameter." ::= {ddmStatusEntry 6} -- ***************************************************************** -- -- Enterprise Trap group -- -- ***************************************************************** END