DI-824VUP+ Firmware Release Note  
Firmware: v1.05
Hardware: A2
Date: Apr 25, 2005

Problems Resolved: (R1.94o8a)
1.Fixed “Show wrong message in the Wizard when the user setups the same passward.”
2.Modify the password item of ppp series to add ********.
3.Mpdify the disable item of Domain filter
4.Modify the wrong message in status page while enabling 128 or 256 Wep key.  
5.Fix”Fails to establish IPSec tunnel with D-Link DFL-100.”
6.Fixed the UI of ddns setting.(???).
7. Fix “static dhcp table only can set up to 15 item after 15 item will show error message.”
8.Fixed”Msn can not login normally,when the user opens port 1723 in the virtual.”
9.Fix the following problems:
(1)  If users choose Group2 or Group5 as the DH-Group of IKE proposal, two DI-824VUP can’t establish IPSec tunnel successfully by using aggressive mode.
10.Support GPRS modem.
11.Support RTP traffic pass-through.
12.Add an additional field of authentication method (including Auto, PAP, CHAP, MS_CHAPv1; Default is Auto) at the Dial-up WAN configuration page.
13.Add Status Connection.
14.Support Netmeeting put the client in the Virtual Server.
15.Add downgrade-presented functionfor new flashrom.


*** V1.02b01(2004-12-13-o5) TO V1.02b01(2004-12-15-o5)

1.Fix "When the user inputs 32 keys or more in WPA_PSK,
  the router will not allow of this setting."

**V1.04(04/10/22 n9) To V1.0401(04/12/13 o5)

1.LAN PCs can't access remote FTP server if router is in SPI mode.

2.Router can't drop PPPoE connection even though the idle time has expired.

3.Fixed "daylight saving when the users setup to span two years."

4.Dynamic VPN can't be reconnected again if remote clients reboot.

**V1.04(04/10/08) To V1.04(04/10/22)

1.Fix"Wireless Setting UI(Radio on/off). 

2.Add Statement in the help of Wireless Setting.

** V1.03b03 TO V1.04(04/10/08)

1. Support Syslog server on WAN side.

2. Fix the device will hang down when WAN & LAN loop-back.

3. Fix speed Enhance Mode function will be disabled when enables WPA-PSK function.

4.Support IPSec NAT-Traversal.

5.There are a lot of incorrect VPN rules in VPN Status window.

6.Fix failed items of CDRouter test.

** V1.03b02 TO V1.03b03(04/09/20)

1.Fix failed items of CDRouter test.

2.Change firewall destination IP from * to real destination IP if the rule is derived from Virtual Server.

3.Support NO-IP DDNS service.

4.Fix the following problem:
  (1) Netmeeting (on Microsoft Windows 2000) is unable to connected success through VPN tunnel.
  (2) Can't establish Manual IPSec tunnel with early firmware version.

5.Add Radio on/off in wireless Configuration.

6.Improve wireless Stable.

** V1.03b01 TO V1.03b02(04/08/30)

1.Support xAuth (Client and Server mode) authentication with IPSec connection.

2.Support i2eye ALG.

3.Prevent different devices from using the same XID to send DHCP request.

4.Fix the following problem:
  (1) Virtual Server doesn't work if public port and private port are not the same.
  (2) Router(with WAN type: Dial-up connection) will auto-reboot if LAN PC reboots.

5.Enhance the wireless performance.(Call G+)

6.Change the value of Max. number of tunnels from 0 to 1.



*** V1.03 TO V1.03b01(04/08/26)

1.Change Firmware Version as V1.03

*** V1.03 TO V1.03b01(04/08/13)

1.Fixed"Some pages are not displayed correctly in Netscape and Mozilla WEB browsers"
2.Add some VPN settings Help.


*** V1.02b01 TO V1.03(04/08/06)

1.Change Firmware Version as V1.03

*** V1.02 TO V1.02b01(04/07/19)

1. If users enable PPTP or L2TP server on DI-824VUP(+),then any WAN host
   can Ping to LAN IP of the router successfully(without establishing PPTP
   or L2TP connection first.
2. More than one PPTP or L2TP clients behind NAT device can't establish PPTP
   or L2TP connetion with DI-824VUP(+) at the same time.(only allow one PPTP
   or L2TP connection.)
3. Fix MAC filter bug.

4. Support 2 or more connections when using MPPE encryption with PPTP and L2TP server.

*** V1.01b04 TO V1.02(04/07/12)

1.Change Firmware Version as V1.02

*** V1.01b03 TO V1.01b04(04/07/08)

1.Add IPSec VPN Keep-alive mechanism.
2.Add D-Link web cameras(DCS-900, 1000, 2000, 3120, 5300) into default lists of Virtual Server.
3.Add MPPE encryption with PPTP and L2TP server.
 (Note. MPPE can only works with MS_CHAP authentication.)
4.Support PPTP WAN type can connect to PPTP server of Microsoft Windows 2000.
5.Change firewall mechanisms.
(It's recommended to reset configuration to factory default after upgrading to this firmware.)
6.The TI Wireless Module is the same with DI-724P(V1.01)

*** V1.01b03 TO V1.01b03(04/06/30)

1.Fixed "the ftp conection is broken in VPN IP-sec Tunnel".

*** V1.01b01 TO V1.01b02

1.Fixed "Linux-Dns server can not query under Nat,when SPI mode is enabled.(Test)
2.Chnage Default Setting "Connect mode select changes as Connect-on-denand
  Maximunm Idle Time is 5 minutes."(Test)
3.Fixed "the ftp conection is broken in VPN IP-sec mode".
4.Support IGMP for Singapore.(Test)
5.Change Ti wireless Card Module and verify wireless stable.(Test)
6.Verify BigPond problem in australia.(Test)
7.Fix the problem about L2TP WAN connection doesn't work in Israel.(Test)

*** V1.01b01 TO V1.01(04/05/12)

1.Change Firmware Version as V1.01.


*** V1.01  TO 1.01b01(04/04/30)

1.Fix UI error when swith VPN configuration pages.

2.Fix the problem about mail alert function can't transfer mail with some SMTP servers,like
  Pchome. 

3.Replace the real key value with asterisks in VPN configuration pages.

4.Support SMTP authentication with mail alert function.

5.Modify the same address of Sender and Receiver in mail alert function. 

*** 1.00b7 TO V1.01(04/04/19)

1.Change Firmware Version as V1.01.

2.Change the sender of Format.(change admin@wan-ip address to admin@domain-name).

But there is still a bug,some mail-servers access to deny for admin@domain-name,
like admin@pchome.com.tw,Amit will modify the same address of Sender and Receiver.
For example,the receiver is D-Link@dlink.com.tw and the Sender is also D-Link@dlink.com.tw.
Amit will modify this by next Fw.
 

*** 1.00b06 TO 1.00b07

1.Support X-Box about TCP Fin-test of UPNP function.

2.Fix "The device can not renew leased-time automatically when wan type is dynnamic ip address."

3.Modify Firewall rule list(change Lan ip 192.168.0.1 to *).   


4.Modify "the wireless connection is down,when DWL-G650+ enables 8x Mode.
*** 1.00b04 TO 1.00b06

1.Fix "When Setuping Mac filter,the setting will skip to Domain Blocking." in Filter Page. 

2.Fix "The System-log will not show filter-log when enabling the rules of domain filter." in the Filter page.

3.Fix "The settings,like Authentication type ,SSID broadcast and 8X Mode will skip in the Perfromance page."

4.Fix "The wireless can not work(The wireless button is gone) when the 
  wan type is ppp(pppoe,l2tp,pptp or dial-up) and enables WPA ro 802.1x."

5.Fix "Power save makes the wirelss connection down,for example,Centrino or wireless-clients enable power-save mode.

6.Fix "The vpn function will authenticate incorrectly when setting many ipsec proposals( different group)."
*** 1.00b03 TO 1.00b04

1. Add Connection Mode select.

2. Add Tx Power function.
*** 1.00b02 TO 1.00b03

1.Change UI title image.

2.Fix Wireless SSID will lost "+" when click WEP disable to enable.

3.Improve the wireless throughput.

4.Fix when Wep setting is not working in Wizard mode.

5.Fix that Wireless tab under Status is not working.

6.Fix that Intersil 11g  can not associate when G mode only.

7.Fix DWL-650+ can not associate when SSID broadcast disables.
*** 1.00b01 TO 1.00b02

1. Add WPA.

2. Add L2TP.

3. Add PeanutHull.

4. Add Daylight Saving.

5. Change Domail Filter seat.

*** 1.00 TO 1.00b01

1. Fix remote management.

2. Fix wireless card fail.

3. Fix DynDNS.org.

3. Fix Wireless SSID will lost "+" when click WEP disable to enable.

*** 1.00

First release.

************************************************
Section D. Platform-independent Firmware Upgrade
************************************************

First, go to the D-Link Web site to download firmware image
file, 824VUP+_100b03.BIN. Remember the location you save this file.
And use the following method to upgrade:

* WEB UPGRADE:

1. Connect the Web user interface and login as system
administrator.

2. Click the "Firmware Upgrade" button of "Tools" page.
And the "Firmware Upgrade" screen will appear.

3. Enter the location of the previously downloaded file in
the text box, or click "Browse" button to search for the
file. And then click "Upgrade" button.