DIR-615Ñ2 release notes history. ==================================================== Firmware: v3.03RU Build: 21beta06 Hardware: C2 Date: Tue, 12 Oct 2010 Firmware Version: ver3.03RUb21beta06 1. Fixed DHCP server webui issue. 2. Support IPv6 v1.12R with cli commands (not support IPv6 Routing and 6rd) 3. Fixed when user only change Lan settings, pop change IP address message. 4. Fixed when ALLOW computers access to ONLY these sites, only can input arabic numeral. 5. Fixed only can input arabic numeral in routing table. 6. Fixed LED behavior is not correct. 7. Fixed configuration save user and admin issue. 1.0. Save the config file. 1.1. Make a factory reset. 1.2. Load the config file. 1.3. Result: The Admin password is away. The User password is still OK. 8. Fixed when QoS mbandwidth >= define value, UI will show "Not Estimate". 9. Modify WEP Auth type "Open or Shared Key" ->"Both or Shared Key" 10. Support router.dlink.com 11. Modify dhcpd_lease_time=1440 12. Fixed when we change the DUT's password and save it.It can't back to login GUI page. 13. Fixed [Status ---> Devices Info ---> LAN Computers] WLAN PCs' information does not be displayed. Firmware: v3.03RU Build: 21beta05 Hardware: C2 Date: Fri, 16 Jul 2010 Firmware Version: ver3.03RUb21beta05 1. Fixed DIR-615_C2_v3.03RUB21Beat04-Broken L2TP dual access client. Firmware: v3.03RU Build: 21beta04 Hardware: C2 Date: Wed, 09 Jun 2010 Firmware Version: ver3.03RUb21beta04 1. Fixed DIR-615_C2_v3.03RUB21beta02-Enable MAC filter cause DUT can not pass multicast flow. Firmware: v3.03RU Build: 21beta03 Hardware: C2 Date: Wed, 03 Jun 2010 Firmware Version: ver3.03RUb21beta03 1. Fixed DIR series HNAP issue firmware request. Firmware: v3.03RU Build: 21beta02 Hardware: C2 Date: Mon, 22 Feb 2010 Firmware Version: ver3.03RUb21beta02 1. Fixed for the DDNS can support other like DDNS server 2. Fixed DCS-2121 don’t reply DHCP Request packet to DHCP server(DIR-615), that’s cause DCS-2121 can’t get IP Address.. Firmware: v3.03RU Build: 21 Hardware: C2 Date: Mon, 18 Jan 2009 Firmware Version: ver3.03RUb21 1. Modify when in AP mode, disable some RT function. 2. Modify when in AP mode, disable qos?ipv6 and upnp function. 3. Fixed TSD bug:for AP mode the wan port LED can't bright issue. 4. Fixed TSD bug:swap AP mode to Router mode cause DNS not work(loss restore advance dns service and wan_specify_dns) 5. Fixed TSD bug:In AP mode, we can configure Gateway and DNS for DUT but it can't access Internet. This cause NTP server in AP mode not work. Firmware: v3.03RU Build: 20 Hardware: C2 Date: Tue, 5 Jan 2009 Firmware Version: ver3.03RUb20 1. Fixed 255.0.0.0/4 can be configured as Russia pptp Gateway IP Address. Firmware: v3.03RU Build: 19 Hardware: C2 Date: Tue, 5 Jan 2009 Firmware Version: ver3.03RUb19 1. Fixed when save wan-L2TP, L2TP password can't save. 2. Fixed pptp account can’t be saved with normal settings switch from l2tp and password missing too. 3. Fixed In L2TP/Russia L2TP, 255.0.0.0/4 can be configured as "L2TP server IP Adress" and in "L2TP Gateway IP Address" 4. Fixed In PPTP, 255.0.0.0/4 can be configured as "PPTP server IP Adress". Firmware: v3.03RU Build: 18 Hardware: C2 Date: Thu, 31 Dec 2009 Firmware Version: ver3.03RUb18 1. Fixed when save wan-L2TP, L2TP password can't save. 2. .Fixed TSD bug NO23:In PPTP/Russia PPTP, 255.0.0.0/4 can be configured as "PPTP server IP Adress". In L2TP/Russia L2TP, 255.0.0.0/4 can be configured as "L2TP server IP Adress" and "L2TP Gateway IP Address" Firmware: v3.03RU Build: 17Beta01 Hardware: C2 Date: Thu, 10 Dec 2009 Firmware Version: ver3.03RUb17beta01 1. Fixed DIR-615_C2_v3.03RU_B09&3.03WWB05-L2TP connection problem in cable infrastructure. Firmware: v3.03RU Build: 17 Hardware: C2 Date: Wed, 25 Nove 2009 Firmware Version: ver3.03RUb17 2. Fixed may cause kernel panic in BT test. 3. Fixed D-Track SIP phone could not work issue . 4. Fixed data rate show error issue. 5. Fixed when select first computer name or IP in Access control not show correct value. 6. Fixed Web pop hostname is invalid when switch back to dhcp mode from other modes Firmware: v3.03RU Build: 16 Hardware: C2 Date: Wed, 11 Nove 2009 Firmware Version: ver3.03RUb16 1. Fixed reservation issue. 1.0 Restore to default. 1.1 Entry a reservation IP, then click "save" button. 1.2 Change the LAN IP. 1.3 Click "Save Settings" button. It can be saved.. 2. Fixed Schedule rule not work when modify the existing rule.(portforward?wireless?access control) 3. Fixed when add new schedule ,wireless will use the newest schedule rule. 4. Fixed when wireless schedule is due but wireless status show enable. 5. Fixed host name can input special char. 6. Fixed user can login to the web UI without authentication remotely 7. Fixed PPTP static IP address can input 255.255.255.255 8 .Fixed L2TP static IP address can input 255.255.255.1 9. Fixed when add new schedule ,wireless will use the newest schedule rule at first time add scheule. 10. Fixed can not add 24 virtual server rules 11. Fixed may cause kernel panic in BT test. Firmware: v3.03RU Build: 15 Hardware: C2 Date: Wed, 07 Oct 2009 Firmware Version: ver3.03RUb15 1. Update routing page follow ubi-com style. 2. Modify CONFIG_IP_CONNTRACK_NUMBER to 16000 Firmware: v3.03RU Build: 14 Hardware: C2 Date: Mon, 28 Sep 2009 Firmware Version: ver3.03RUb14 1. Fixed An error page show when switch back to dhcp mode. Firmware: v3.03RU Build: 13 Hardware: C2 Date: Mon,28 Sep 2009 Firmware Version: ver3.03RUb13 2. Fixed An error page show when switch back to dhcp mode. Firmware: v3.03RU Build: 12 Hardware: C2 Date: Fri, 25 Sep 2009 Firmware Version: ver3.03RUb12 1. Fixed LAN PC can NOT access WAN network. (LAN IP is not transferred to WAN IP). Steps: 1.Set WAN type to Russia PPPoE or Russia PPTP or Russia L2TP 2.Click “Save Setting” 3.Change WAN type back to DHCP mode Firmware: v3.03RU Build: 11 Hardware: C2 Date: Tue, 22 Sep 2009 Firmware Version: ver3.03RUb11 1. Fixed when change computer name in DHCP reservation will occur error. 2. Remove support page.(Email Notification of Newer Firmware Version) 3. Fixed UI can store different ip segment reservation at first time , and push save button at second step pop warning. 4. Fixed TSD#6: web filter rule issue. Test procedure 1. Input http://www.google.com.tw and www.google.com.tw in the website filter rule. 2. Click save button. 3. The rule can be saved. Firmware: v3.03RU Build: 10 Hardware: C2 Date: Thu, 17 Sep 2009 Firmware Version: ver3.03RUb10 1.Fixed Ipv6 ping test always show success. 2.Fixed Web UI pop message when switch from PPPoE/PPTP/L2TP/Russia PPPoE/PPTP/L2TP to DHCP without change then save it. Firmware: v3.03RU Build: 09 Hardware: C2 Date: Tue, 15 Sep 2009 Firmware Version: ver3.03RUb09 1. Remove DHCP routing option from UI. 2. Set classless_static_route default = 1. Firmware: v3.03RU Build: 08 Hardware: C2 Date: Tue, 15 Sep 2009 Firmware Version: ver3.03RUb08 1.Fixed:"Russia PPoE" wording error in suppport->device page. 2.Fixed Web UI error when switch between PPPoE/PPTP/L2TP to Russia PPPoE/PPTP/L2TP. (switch to another mode without changing then save it) 3.Fixed IPv6 option is not presented in "Access Control" setting page.(in policy name step and later steps) 4.Fixed Previous configured Port range is still valid to protocol of "Any". Firmware: v3.03RU Build: 07 Hardware: C2 Date: Fri, 11 Sep 2009 Firmware Version: ver3.03RUb07 1.Fixed:No "Russia PPTP", "Russia L2TP" and "Russia PPPoE" descriptions. 2.Fixed: No description for “Routing” function. 3.Remove support page.(Extra Wireless Protection) 4.Remove support page.(“Email Notification of Newer Firmware Version) 5.Fixed Web UI error when switch between PPPoE/PPTP/L2TP to Russia PPPoE/PPTP/L2TP. 6.Fixed DHCP client fail with DSL-320B ZPIB when Advanced DNS enabled. 7.Fixed IPv6 host or IP is not presented after clicking "PING" in system check. 8.Fixed In Static IPv6 setting, "Change Not saved" warning message pop-up when trying to switch to other pages WITHOUT any configuration changed. 9.Fixed IPv6 option is not presented in "Access Control" setting page. 10.Fixed Based on D-link router spec of 2008/12/11 v1.00, "RU" FW should support multicast group of 239.x.x.x. 11.Fixed https://aaa.bbb.ccc becomes https:/ after clicking save settings. 12.Fixed Wake-On-LAN should support ports other than "9". 13.Fixed Previous configured Port range is still valid to protocol of "Any". 14.Fixed Static IP mode of Russia PPPoE WAN physical can be saved as BLANK. 15.Fixed Set NetBIOS Scope to “abc,123”, setting CAN be saved but the announced NetBIOS scope becomes “abc”. 16.Fixed Network Settings UI Bug: Change Router LAN IP and add DHCP reservation at the same time, the DHCP reservation rule can't be saved. Firmware: v3.03RU Build: 06 Hardware: C2 Date: Thu, 25 Jun 2009 Firmware Version: ver3.03RUb06 1. Fixed that DNS will be replace by DHCP DNS at RS-PPTP static mode. Firmware: v3.03RU Build: 05 Hardware: C2 Date: Thu, 24 Jun 2009 Firmware Version: ver3.03RUb05 1. Fixed that url filter can't work. Example for input http://www.yahoo.com.tw/ or http://www.yahoo.com.tw 2. Fixed rs-pptp/l2tp link fail in dynamic mode (static mode switch dynamic mode then repower DUT) 3. Fixed Rs-pptp/l2tp will use the second dns ip for querying when dhcp server’s the fist dns ip is the same segment as dhcp ip range (static mode to dynamic mode) Firmware: v3.03RU Build: 04 Hardware: C2 Date: Thu, 19 Jun 2009 Firmware Version: ver3.03RUb04 1. Fixed DUT still use old dns ip in rs-pptp static mode to guery pptp server Firmware: v3.03RU Build: 03 Hardware: C2 Date: Thu, 18 Jun 2009 Firmware Version: ver3.03RUb03 1. Fixed DUT will cash DNS IP address in wizard Russia PPTP and Russia L2TP. Firmware: v3.03RU Build: 02 Hardware: C2 Date: Wed, 17 Jun 2009 Firmware Version: ver3.03RUb02 1. Wizard support Russia PPTP and Russia L2TP FQDN. 2. Fixed that the length of FQDN Server IP Address not enough. 3. Fixed that url filter can't work. Example for input http://www.yahoo.com.tw/. Firmware: v3.03RU Build: 01 Hardware: C2 Date: Tue, 16 Jun 2009 Firmware Version: ver3.03RUb01 1. Fixed when Enable "Turn MAC Filtering ON and ALLOW computers listed to access the network" function and no input any MAC Address rule, it should appear warning message. 2. Fixed that cannot run Web Filter and MAC filtering at the same time issue. 3. GUI show allowed char for setting of Device name and Local Domain name. 4. Link-local only for IPv6 issue. 5. Modify when we do reset to unconfigured the wps_pin and wps_default_pin is kepp it to fixed the wps_pin and wps_default_pin is changed to 00000000 when we do reset to unconfigured. 6. Fixed the bug that CAPCHIA (auth graph) can be hacked. -Here is CAPTCHA feedback. http://www.theregister.co.uk/2009/05/15/dlink_router_gimmick/ http://www.sourcesec.com/2009/05/12/d-link-captcha-partially-broken/ 7. Manual Uplink speed issue. Max transmission rate should be between 20 kbps and 100 Mbps. 8. Fixed login format same as DIR-655. 9. Fixed turn on virtual server with schedule will cause could not access internet. 10. Fixed schedule over night issue. 11. Verify BT cert. 12. Set default Admin/User password field blank. 13. modify D-Link System to D-Link Corporation. 14. Fixed bug that safari can not login success with graph 15. Fixed MAC address starting with 08:00:46:EE:D1:C8 won't be accepted. (Ex:MAC can not accept 02,04,08... at beginning). 16. Fixed Enable Application Rules function with the schedule rule that create manually cause LAN packets can't route to WAN. 17. Fixed an error pop when edit access control rule in schedule step (IE7). 18. Fixed that Uplink speed Field can be saved with blank. 19. Fixed when changed the wps_pin the wps is into configured mode. 20. Fixed System time roll back after rc restart. 21. Disable auth graph. 22. Fixed D-Track - HQ20090525000007-DIR-615_Cx_v3.02twb02-MAC filter function do not work. (DIR-615 Cx v3.02TW_b02 can not save MAC filtering settings. It shows the message to remind the users that the settings is not ALLOW. But after clicking OK, the settings are not saved.By the way, the warning message is not exactly correct.) 23. Fixed can't setting domain name. ex: domain name=cameo.com 24. Fixed pop message is wrong when device name is wrong only. 25. Fixed login button is not complete (safari 4-cn in winxp-cn) 26. Fixed login button is disappear in Firefox-3.0..10-cn Firmware: v3.02RU Build: 08 Hardware: C2 Date: Wed, 13 May 2009 Firmware Version: ver3.02RUb08 1. Fixed SSID cannot display '\' on status page. 2. Add OPENDNS function. 3. Fixed port forwarding cannot save over 8 rules. 4. Fixed all on-line account will be change to last login account issue. 5. Fixed when set "http://" inf url filter, the function will fail. 6. Fixed that Mac Safari can not show auth pic 7. Support FQDN function. Firmware: v3.02RU Build: 07 Hardware: C2 Date: Tue, 14 Apr 2009 Firmware Version: ver3.02RUb07 1. Modify wpa-psk personal cipher type to tkip and aes. 2. Fixed WPS.HW push-button, sw push-button, WPS pin fail by Dlink report Firmware: v3.02RU Build: 06 Hardware: C2 Date: Fri, 10 Apr 2009 Firmware Version: ver3.02RUb06 3. Fixed: When I choose "Turn MAC Filtering ON and ALLOW computers listed to access the network" function and I don't input any MAC address, It should can't save settings. Firmware: v3.02RU Build: 05 Hardware: C2 Date: Wed, 08 Apr 2009 Firmware Version: ver3.02RUb05 1.Fixed:PPTP, L2TP and Russia PPTP can't connect to PPTP/L2TP server by special Character. EX.Set Username:"tsd" and Password: "1qaz2ws\" into Server. 2.Fixed:When I choose "Turn MAC Filtering ON and ALLOW computers listed to access the network" function and I don't input any MAC address, It should can't save settings. 3.Fixed:The Time Zone incorrect for Newfoundland that should be GMT-03:30. 4.Fixed:The LAN status does not updated when LAN clients change. 5.Fixed:The web UI display issue for logs 6.Add Wake-on-lan. 7.Remove message "Can't choose WPA-Personal/TKIP and AES when WPS is enable!!" 8. Fixed SIP phone with purple IOT issue Firmware: v3.02RU Build: 04 Hardware: C2 Date: Tue, 16 Mar 2009 Firmware Version: ver3.02RUb04 1.Fixed:When I set Russia PPTP/PPPoE mode in WAN type, and then change to PPTP/PPPoE. It can't change back to PPTP/PPPoE WAN type. 2.Fixed:When setting Wake-on-LAN in Virtual Server, it couldn't allow to setting "X.X.X.255" 3.Fixed:When setting Special AP--> PalTalk, the protocol type for firewall should display "Any" not "TCP". 4.Fixed:The uplink speed could not be measured when QoS function enabled. 5.Fixed:The firmware upgrade notify shows incorrect information. Firmware: v3.02RU Build: 03 Hardware: C2 Date: Mon, 22 Dec 2008 Firmware Version: ver3.02RUb03 1.Fixed:WEB UI can’t input WPA-EAP setting. 2.Fixed:WEB UI would pop-up error message on log in page when disabled graphical authentication. 3.Fixed:please remove duplicate statement on routing helpful hints. 4.Fixed:Week in schedule for wireless fail. Firmware: v3.02RU Build: 02 Hardware: C2 Date: Tue, 16 Dec 2008 Firmware Version: ver3.02RUb02 1. Fixed:Routing rule 21~32 can not work. 2. Fixed:Schedule should pop warning message when user try to edit or delete schedule rule in used for wireless. 3. Add Russia L2TP function. Firmware: v3.02RU Build: 01 Hardware: C2 Date: Mon, 15 Dec 2008 Firmware Version: ver3.02RUb01 4. Add Graph Auth. 5. Add Static routing page. 6. Add RFC 3442 option. 7. Add Routing information. 8. Add wireless schedule. 9. Add ALG function Firmware: v3.01RU Build: 04 Hardware: C2 Date: Mon, 17 Nov 2008 Firmware Version: ver3.01RUb04 1. Test RTSP function Firmware: v3.01RU Build: 03 Hardware: C2 Date: Mon, 6 Oct 2008 Firmware Version: ver3.01RUb03 1.Fixed Hardware version display wrong. 2.Fixed Russia PPPoE/PPTP display issue. Firmware: v3.01RU Build: 02 Hardware: C2 Date: Thu, 2 Oct 2008 Firmware Version: ver3.01RUb02 1.Fixed Russia mode when PPP not connect to server, the status page will show physical IP. Firmware: v3.01RU Build: 01 Hardware: C2 Date: Wed, 24 Sep 2008 Firmware Version: ver3.01RUb01 1.First release base on 3.01B11 2.Add Russia PPTP/PPPoE 3.Add static routing